journal article·2019-09

Influence of Wear Particles and Reverse Transfer of the Material on Wear Intensity of Aluminum Alloy under Dry Friction on Steel

N. M. Rusin, A. L. Skorentsev, I. V. Vlasov

Journal of Friction and Wear· Volume 40· Issue 5
Publisher page

Abstract

Sintered Al-40Sn samples were subjected to tribological tests by the “pin-on-disk” scheme without liquid lubrication. A steel disk was pressed to the upper and lower face surfaces of a vertically located sample. It is revealed that the location of counterbodies relative to the frictional contact plane can significantly influence their wear intensity. These differences are explained by the different composition and structure of friction surfaces of counterbodies the nature of formation of which depends on the gravity vector direction defining the features of displacement of wear particles over the friction surface.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Metal Alloys Wear and Properties · Mechanical stress and fatigue analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (10)

Show source-provided references
1. Belov, N.A., et al., Alyuminievye splavy antifriktsionnogo naznacheniya (Antifriction Aluminum Alloys), Mironov, A.E., Belov, N.A., and Stolyarova, O.O., Eds., Moscow: Mosk. Inst. Stali Splavov, 2016.
2. Bertelli, F., Freitas, E.S., Cheung, N., Arenas, M.A., et al., Microstructure, tensile properties and wear resistance correlations on directionally solidified Al–Sn–(Cu; Si) alloys, J. Alloys Compd., 2017, vol. 695, pp. 3621–3631.10.1016/j.jallcom.2016.11.399 ↗
3. Epifanov, G.I. and Minaev, N.I., Friction as shear resistance of thin surface layers of solids, in Sukhoe i granichnoe trenie. Friktsionnye materialy (Dry and Boundary Friction. Friction Materials), Moscow: Akad. Nauk SSSR, 1960, no. 2, pp. 50–57.
4. Babic, M., Mitrovic, S., and Nikovic, R., Tribological potential of zinc–aluminum alloys improvement, Tribol. Ind., 2009, vol. 31, no. 1, pp. 15–28.
5. Rusin, N.M. and Skorentsev, A.L., Tribotechnical properties of sintered aluminum alloys, Appl. Mech. Mater., 2014, vol. 682, pp. 9–13.10.4028/www.scientific.net/AMM.682.9 ↗
6. Tripathy, M.R., Manoj Kumar, B.V., Basu, B., Dube, R.K., and Koria, S.C., Tribological behavior of steel backed Al–Sn strip prepared via spray atomisation–deposition–rolling route, Mater. Sci. Technol., 2007, vol. 23, no. 1, pp. 15–22.10.1179/174328407X154392 ↗
7. Uthayakumar, M., Thirumalai Kumaran, S., and Aravindan, S., Dry sliding friction and wear studies of fly ash reinforced AA-6351 metal matrix composites, Adv. Tribol., 2013, vol. 3, art. ID 65602.
8. Cree, D. and Pugh, M., Dry wear and friction properties of an A356/SiC foam interpenetrating phase composite, Wear, 2011, vol. 272, pp. 88–96.10.1016/j.wear.2011.07.008 ↗
9. Rusin, N.M., Skorentsev, A.L., and Kolubaev, E.A., Dry friction of pure aluminum against steel, J. Frict. Wear, 2016, vol. 37, no. 1, pp. 86–93.10.3103/S1068366616010141 ↗
10. Stolyarova, O.O., Muravyeva, T.I., Zagorskiy, D.L., and Gubenko, M.M., Investigation of the surface of antifriction Al–Cu–Si–Sn–Pb aluminum alloys, J. Surf. Invest.: X-Ray, Synchrotron Neutron Tech., 2017, vol. 11, pp. 832–839.10.1134/S1027451017040292 ↗