Study of the Influence of the Parameters of Ultrasonic Treatment of Motor Oil on the Wear of Friction Pairs during the Burn-In Period
Source abstract
Abstract
Abstract Results of studies of the surface and wear characteristics of roller—pad friction pairs in burn-in tests with motor oil treated with ultrasound at different frequencies are presented. It has been found that the treatment of oil with ultrasound at a frequency of 17 kHz leads to an increase in the pre-score load by 22.2% and a decrease in the friction coefficient by 13.1% with the optimal load increasing by 12.5%. The treatment of oil at a frequency of 12 kHz results in an increase in the score resistance by 6.5% and a decrease in the friction coefficient by 3.6%. The optimal load does not change in this case compared with the results of tests conducted using untreated oil. When the oil was treated at a frequency of 8 kHz, no significant differences between the values under study were observed. A decrease in the value of roughness parameter Ra for the samples treated with ultrasound at a frequency of 17 kHz by 50% and 78.2% was established for the roller and pad, respectively.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Tribology and Wear Analysis · Mechanical Systems and Engineering · Surface Treatment and Coatings
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (8)
Show source-provided references
1. Koval’skii, B.I., RF Patent 2514189, Byul. Izobret., 2014, no. 23.
2. Ametov, V.A., et al., RF Patent 19100, Byul. Izobret., 2001, no. 22.
3. Misheninm D.N., Activation of lubricants by laser radiation and an improvement of the operational parameters of tribomechanical systems in device engineering, Extended Abstract of Cand. Sci. (Eng.) Dissertation, Moscow: Tsiolkovskii Russ. State Technol. Univ., 2000.
4. Magomedbekov, E.P., Sazonov, A.B., and Ermakov, V.I., Influence of γ-radiation on the physicochemical properties of VM-4 and VM-5 oils, Issled. Ross., 2004, no. 7, pp. 534–543.
5. Zhosan, A.A., Revyakin, M.M., and Golovin, S.I., Effect of gamma radiation on the performance properties of mineral-based motor oils, Elektron. Obrab. Mater., 2018, vol. 54, no. 1, pp. 75–79.
6. Kargin, B.S., Anishchenko, A.S., Kargin, S.B., Khiora, V.S., Tkachev, R.O., and Voronina, N.A., The effect of ultrasonic vibrations on the effectiveness of technological lubricants, Visn. Priazov. Derzh. Tekh. Univ., Ser.: Tekh. Nauki, 2015, vol. 1, no. 30, pp. 136–140.
7. Pokrovskaya, S.V., Oshchepkova, N.V., Zavadskii, A.V., and Bulavka, Yu.A., Ultrasonic cavitation treatment of colloidal lubricant systems, Vestn. Polotskogo Gos. Univ., Ser. B, 2012, no. 3, pp. 109–113.
8. Simdyankin, A.A., Uspensky, I.A., Pashchenko, V.M., and Starunsky, A.V., Ultrasonic machining of engine lubricating oil during tribotechnical testing, J. Frict. Wear, 2017, vol. 38, no. 4, pp. 311–315.10.3103/S1068366617040134 ↗