journal article·2019-11

Interrelation of Surface Temperature and Tribological Characteristics of a Protective Coating on a Tool

H. Al-Ethari, K. Y. Al-Dulaimi, B. Warcholinski, T. A. Kuznetsova

Journal of Friction and Wear· Volume 40· Issue 6
Publisher page

Abstract

The study investigates the thermal and tribological characteristics of an uncoated P10 carbide tool and one coated with titanium carbide. Turning tests were conducted on AISI 1020 steel at four spindle speeds (80, 315, 500, and 800 rpm), two feed rates (0.2 and 0.5 mm/rev), and two cut depths (0.5 and 0.7 mm). The temperature change at the tool–workpiece interface, flank wear width, lifetime of tools, and roughness of the machined surface were determined. It is shown that the TiC coating significantly reduces temperature rise and flank wear during cutting. The lifetime of coated tools is about four times longer compared to uncoated tools. Coated tools also showed improved surface quality.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Tribology and Wear Analysis · Surface Treatment and Coatings · Material Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (13)

Show source-provided references
1. Zhdanok, S.A., Sviridenok, A.I., Ignatovskii, M.I., Krauklis, A.V., Kuznetsova, T.A., Chizhik, S.A., and Borisevich, K.O., On the properties of a steel modified with carbon nanomaterials, J. Eng. Phys. Thermophys., 2010, vol. 83, no. 1, pp. 1–5.10.1007/s10891-010-0312-8 ↗
2. Jindal, P.C., Santhanam, A.T., Schleinkofer, U., and Shuster, A.F., Performance of PVD TiN, TiCN, and TiAlN coated cemented carbide tools in turning, Int. J. Refract. Met. Hard Mater., 1999, vol. 17, p. 163.10.1016/S0263-4368(99)00008-6 ↗
3. Brito, R.F., Carvalho, S.R., Lima e Silva, S.M.M., and Ferreira, J.R., Thermal analysis in coated cutting tools, Int. Commun. Heat Mass Transfer, 2009, vol. 36, pp. 314–321.10.1016/j.icheatmasstransfer.2009.01.009 ↗
4. Rech, J., Kusiak, A., and Battaglia, J.L., Tribological and thermal functions of cutting tool coatings, Surf. Coat. Technol., 2004, vol. 186, pp. 364–371.10.1016/j.surfcoat.2003.11.027 ↗
5. Rech, J., Battaglia, J.L., and Moisan, A., Thermal influence of cutting tool coatings, J. Mater. Process. Technol., 2005, vol. 159, pp. 119–124.10.1016/j.jmatprotec.2004.04.414 ↗
6. Kusiak, A., Battaglia, J.-L., and Rech, J., Tool coatings influence on the heat transfer in the tool during machining, Surf. Coat. Technol., 2005, vol. 195, pp. 29–40.10.1016/j.surfcoat.2005.01.007 ↗
7. Arrazola, P.-J., Aristimuno, P., Soler, D., and Childs, T., Metal cutting experiments and modelling for improved determination of chip/tool contact temperature by infrared thermography, CIRP Ann., 2015, vol. 64, pp. 57–60.10.1016/j.cirp.2015.04.061 ↗
8. Feng, X., Zhang, Y., Hu, H., Zheng, Y., Zhang, K., and Zhou, H., Comparison of mechanical behavior of TiN, TiNC, CrN/TiNC, TiN/TiNC films on 9Cr18 steel by PVD, Appl. Surf. Sci., 2017, vol. 422, pp. 266–272.10.1016/j.apsusc.2017.05.042 ↗
9. Kone, F., Czarnota, C., Haddag, B., and Nouari, M., Finite element modelling of the thermo-mechanical behavior of coatings under extreme contact loading in dry machining, Surf. Coat. Technol., 2011, vol. 205, pp. 3559–3566.10.1016/j.surfcoat.2010.12.024 ↗
10. Rech, J., Arrazola, P.J., Claudin, C., Courbon, C., Pusavec, F., and Kopac, J., Characterization of friction and heat partition coefficients at the tool-work material interface in cutting, CIRP Ann., 2013, vol. 62, pp. 79–82.10.1016/j.cirp.2013.03.099 ↗
11. Zhang, S. and Liu, Z., An analytical model for transient temperature distributions in coated carbide cutting tools, Int. Commun. Heat Mass Transfer, 2008, vol. 35, pp. 1311–1315.10.1016/j.icheatmasstransfer.2008.08.001 ↗
12. Li, B., A review of tool wear estimation using theoretical analysis and numerical simulation technologies, Int. J. Refract. Met. Hard Mater., 2012, vol. 35, pp. 143–151.10.1016/j.ijrmhm.2012.05.006 ↗
13. Mia, M. and Dhar, N.R., Modeling of surface roughness using RSM, FL and SA in Dry hard turning, Arab. J. Sci. Eng., 2018, vol. 43, pp. 1125–1136.10.1007/s13369-017-2754-1 ↗