Tribological Properties of Sintered Al–Sn Alloy Doped with Iron
Source abstract
Abstract
Antifriction alloys of the Al–Sn system are widely used as coatings for plain bearing inserts, to increase the strength of which dispersion hardening is used. A mixture of the Al–7Fe–38Sn composition (wt %) from elemental Al, Sn, and Fe powders was sintered in vacuum for 1 h at temperatures below (570°C) and above (710°C) the melting point of aluminum. Then, the sintered cylindrical briquettes with a diameter of 20 mm were additionally compacted at 250°C and ~300 MPa by double-sided compression in a closed mold with a channel of the same diameter. The mechanical properties of the prepared composites were determined by their compression test. Tribological tests of the composites were carried out according to the “pin-on-disk” scheme using a Tribotechnic tribotester (France). At both sintering temperatures, a composite material with tin interlayers and agglomerates of tin-cemented small aluminides located between aluminum grains was found to be formed. The composite prepared by sintering the mixture with iron nanoparticles has the maximal strength and wear resistance under dry friction against a steel disc. It was found that hard particles in composites of the Al–Sn system with a high content of the soft phase can be used as an effective means of increasing the wear resistance if they are uniformly distributed along the matrix grain boundaries during the preparation of the composite. In this case, the particles effectively prevent the localization of deformation in the tin interlayers separating the grains. As a result, the gradient of deformation of the material in the subsurface layer decreases. Thus, the time of wear particles formation and, consequently, the wear resistance of composites of the Al–Sn system increase. With an increase in pressure on the friction surface, the wear intensity of the composite samples increases and the value of the friction coefficient decreases.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Powder Metallurgy Techniques and Materials · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. Bushe, N.A., Goryacheva, I.G., and Makhovskaya, Yu.Yu., The effect of the phase composition of antifriction aluminium alloys on their self-lubrication in friction, J. Frict. Wear, 2002, vol. 23, no. 4, pp. 46–55.
2. An, J., Liu, Y.B., Lu, Y., Wang, J., and Ma, B., Friction and wear characteristics of hot-extruded leaded aluminum bearing alloys, J. Mater. Eng. Perform., 2002, vol. 11, pp. 433–443.10.1361/105994902770343971 ↗
3. Liu, X., Zeng, M.Q., Ma, Y., and Zhu, M., Promoting the high load-carrying capability of Al-20 wt.% Sn bearing alloys through creating nanocomposite structure by mechanical alloying, Wear, 2012, vols. 294–295, pp. 387–394.10.1016/j.wear.2012.07.021 ↗
4. Bertelli, F., Freitas, E.S., Cheung, N., Arenas, M.A., et al., Microstructure, tensile properties and wear resistance correlations on directionally solidified Al–Sn–(Cu;Si) alloys, J. Alloys Compd., 2017, vol. 695, pp. 3621–3631.10.1016/j.jallcom.2016.11.399 ↗
5. Tripathy, M.R., Manoj Kumar, B.V., Basu, B., Dube, R.K., and Koria, S.C., Tribological behavior of steel backed Al–Sn strip prepared via spray atomization–deposition–rolling route, Mater. Sci. Technol., 2007, vol. 23, pp. 15–22.10.1179/174328407X154392 ↗
6. Mironov, A.E. and Kotova (Karacharova), E.G., Development of new grades of cast aluminum antifriction alloys for replacing bronzes in friction units, Izv. Samar. Nauch. Tsentra RAN, 2011, vol. 13, no. 4, pp. 1136–1140.
7. Budinski, K.G., Friction, Wear, and Erosion Atlas, Boca Raton, FL: CRC, 2013.10.1201/b15984 ↗
8. Rusin, N.M., Skorentsev, A.L., and Kolubaev, E.A., Effect of equal channel angular pressing on mechanical and tribological properties of sintered Al–Sn composites, J. Mater. Eng. Perform., 2020, vol. 29, pp. 1955–1963.10.1007/s11665-020-04704-1 ↗
9. Rusin, N.M. and Skorentsev, A.L., Stages of plastic flow of silumin-matrix-based composites during compression, Phys. Met. Metallogr., 2019, vol. 120, no. 8, pp. 813–818.10.1134/S0031918X19080131 ↗
10. Kozlov, E.V., Glezer, A.M., Koneva, N.A., Popova, N.A., and Kurzina, I.A., Osnovy plasticheskoi deformatsii nanostrukturnykh materialov (Fundamentals of Plastic Deformation of Nanostructured Materials), Moscow: Fizmatlit, 2016.
11. Rusin, N.M., Skorentsev, A.L., and Vlasov, I.V., Influence of wear particles and reverse transfer of the material on wear intensity of aluminum alloy under dry friction on steel, J. Frict. Wear, 2019, vol. 40, no. 5, pp. 396–403.10.3103/S1068366619050131 ↗
12. Dokhov, M.P., Kokoeva, M.N., and Sherieva, E.H., Wetting of iron and copper with liquid tin, lead and calculation of their interfacial energies, Kondens. Sredy Mezhfaz. Granitsy, 2019, vol. 21, no. 3, pp. 385–389.
13. Liu, Y., Yin, F., Hu, J., et al., Phase equilibria of Al–Fe–Sn ternary system, Trans. Nonferr. Met. Soc. China, 2018, vol. 28, pp. 282–289.10.1016/S1003-6326(18)64661-8 ↗
14. Makhovskaya, Y.Y. and Goryacheva, I.G., Modeling of soft phase transfer to the surface of multicomponent aluminum alloy in friction, Phys. Mesomech., 2016, vol. 19, pp. 239–247.10.1134/S1029959916030024 ↗
15. Zeng, M.Q., Hu, R.Z., Song, K.Q., Dai, L.Y., and Lu, Z.C., Enhancement of wear properties of ultrafine-structured Al–Sn alloy-embedded Sn nanoparticles through in situ synthesis, Tribol. Lett., 2019, vol. 67, p. 84.10.1007/s11249-019-1195-2 ↗