Evaluation of the strength, wear, and durability of a corrected cylindrical involute gearing, with due regard for the tooth engagement conditions
Source abstract
Abstract
A method for calculating the wear and durability of helical gearings is used to investigate the effect of double–single–double tooth engagement on the maximum contact pressures, tooth wear, and durability of a corrected cylindrical involute gearing under constant tooth contact conditions. A technique is presented for determination of the angles of transition from the doubleto the single-tooth contact and vice versa. Gear tooth profile correction is found to reduce the maximum contact pressures by up to 20%. The teeth of the gear wheel reach their wear allowance faster than those of the pinion do. Depending on the degree of correction, the maximum wear occurs at different characteristic contact points: at the entry to the double-tooth mesh, at the entry to the single-tooth mesh, or at the exit out of the mesh. The durability of the gearing is found to be at its maximum at certain overlap ratios, its magnitude being observed to increase substantially (by up to 50%). The results obtained are presented in graphic form, which enables one to reveal the laws governing the effect of the engagement conditions.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Gear and Bearing Dynamics Analysis · Metal Alloys Wear and Properties · Engineering Technology and Methodologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (11)
Show source-provided references
1. Pasta, A. and Mariotti, V.G., Finite element method analysis of a spur gear with a corrected profile, J. Strain Anal., 2007, vol. 42, pp. 281–292.10.1243/03093247JSA284 ↗
2. ISO 6336-2. Calculation of Load Capacity of Spur and Helical Gears. Part 2: Calculation of Surface Durability (Pitting), Genewa: Int. Organ. Standard., 1966.
3. Ulaga, S.M., Ulbin, M., and Flasker, J., Contact problems of gears using overhauser splines, Int. J. Mech. Sci., 1999, vol. 41, pp. 385–395.10.1016/S0020-7403(98)00073-3 ↗
4. Zwolak, J. and Wittek, M., Optimization of the geometrical parameters of toothed gears in the aspect of contact stress minimization, Tribologia, 2011, vol. 45, pp. 283–291.
5. Drozdov, Yu.N., To the development of calculation method for wearing and friction modeling, in Iznosostoikost (Wear-Resistance), Moscow: Nauka, 1975.
6. Pronikov, A.S., Nadezhnost’ mashin (Reliability of Machines), Moscow: Mashinostroenie, 1978.
7. Flodin, A. and Anderson, S., Wear simulation of spur gears, Tribotest J., 1999, vol. 5, pp. 225–250.10.1002/tt.3020050303 ↗
8. Shil’ko, S.V. and Starzhinskii, V.E., Wear-resistance calculation of toothed wheel gear with wheels from reinforced composition materials, Trenie Iznos, 1993, vol. 14, pp. 444–451.
9. Otsinka dovgovichnosti,, znoshuvannya ta kontaktnoi mitsnosti zubchastikh peredach (Estimation of Durability, Wear and Contact Strength of Toothed Gears), Chernets, M.V., Ed., Drogobych: Vymir, 2002.
10. Chernets’, M.V. and Bereza, V.V., To the question about conformities to the law of influence on longevity and wear of the cylinder evolvent gearing of their basic parameters. Part 1. Transmissions with direct indents, Probl. Tribol., 2010, no. 3, pp. 11–17.
11. Chernets’, M.V. and Bereza, V.V., To the question about conformities to the law of influence on longevity and wear of the cylinder evolvent gearing of their basic parameters. Part 2. Transmissions with slanting indents, Probl. Tribol., 2010, no. 4, pp. 52–59.