journal article·2024-08

Dependence of Gear Tooth Wear on the Misalignment Angle in Gear Meshes

F. G. Nakhatakyan, D. F. Nakhatakyan

Journal of Friction and Wear· Volume 45· Issue 4
Publisher page

Abstract

Abstract The dependence of gear tooth wear on the angle of skew is investigated. It is noted that in gear mechanisms, due to elastic deformations of the elements, manufacturing and installation errors, the symmetry of the system’s compliance is violated, and instead of nominal contact between the teeth, edge contact takes place. As a result, there is a concentration of stresses in the places of initial contact of the teeth, contact stresses sharply increase in these places, which in turn cause increased wear of the teeth in these zones. Because of this, the load capacity of the transmission is reduced, and the durability of the entire mechanism is also significantly reduced. From what has been said, it is important to establish the dependence of the wear value on the transmission load parameters, primarily on the angle of skew. The problem was solved using the method proposed in the paper using an elastic base model. In order to increase the accuracy of matching the specified model with the real picture, a bed with a variable base coefficient is used in the work. Formulas are obtained in closed form for the amount of wear as a function of the skew angle. Verification of these formulas according to the experimental data available in the literature has shown good convergence. It was found that the misalignment significantly increases tooth wear. The results can be useful in the design of gearboxes with cylindrical gears.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Gear and Bearing Dynamics Analysis · Metal Alloys Wear and Properties · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. Drozdov, Yu.N., Pavlov, V.G., and Puchkov, V.N., Trenie i iznos v ekstremal’nykh usloviyakh (Friction and Wear in Extreme Conditions), Moscow: Mashinostroenie, 1986.
2. Gorlenko, O.A. and Makarov, G.N., Computational procedure of wear resistance of gear transmission teeth under skew of the axes of conjugated wheels, J. Frict. Wear, 2019, vol. 40, no. 5, pp. 437–440. https://doi.org/10.3103/s106836661905004010.3103/s1068366619050040 ↗
3. Tunalioğlu, M.Ş. and Tuç, B., Theoretical and experimental investigation of wear in internal gears, Wear, 2014, vol. 309, nos. 1–2, pp. 208–215. https://doi.org/10.1016/j.wear.2013.11.01610.1016/j.wear.2013.11.016 ↗
4. Baydoun, S., Fouvry, S., and Descartes, S., Modeling contact size effect on fretting wear: A combined contact oxygenation—Third body approach, Wear, 2022, vols. 488–489, p. 204168. https://doi.org/10.1016/j.wear.2021.20416810.1016/j.wear.2021.204168 ↗
5. Petrica, M., Duscher, B., Koch, T., and Archodoulaki, V.M., Impact of surface roughness and contact pressure on wear behaviour of PEEK, POM, and PE-UHMW, Int. J. Surf. Sci. Eng., 2017, vol. 11, no. 1, pp. 65–84. https://doi.org/10.1504/ijsurfse.2017.08295510.1504/ijsurfse.2017.082955 ↗
6. Kong, W., Zhang, D., Tao, Q., Chen, K., Wang, J., and Wang, Sh., Wear properties of the deep gradient wear-resistant layer applied to 20CrMnTi gear steel, Wear, 2019, vols. 424–425, pp. 216–222. https://doi.org/10.1016/j.wear.2019.02.02610.1016/j.wear.2019.02.026 ↗
7. Chen, J., Wang, J.-J., and Liu, C.-M., Impact wear resistance and wear mechanism of medium manganese high carbon steel, Trans. Mater. Heat Treat., 2020, vol. 41, no. 1, pp. 73–79. https://doi.org/10.13289/j.issn.1009-6264.2019-034110.13289/j.issn.1009-6264.2019-0341 ↗
8. Tian, H., Han, H., Zhao, Zh., Han, Ch., and Ma, H., Wear prediction and meshing characteristics for the planetary gear set considering angular misalignment and rotating carrier, Eng. Failure Anal., 2022, vol. 140, p. 106583. https://doi.org/10.1016/j.engfailanal.2022.10658310.1016/j.engfailanal.2022.106583 ↗
9. Gorlenko, O.A. and Makarov, G.N., Design of spur gears under the condition of minimizing contact stresses, Izvestiya Volgogradskogo Gosudarstvennogo Tekhnicheskogo Universiteta, 2017, no. 9, pp. 12–14.
10. Airapetov, E.L. and Nakhatakyan, F.G., Calculation model of tooth wear of inaccurate and deformable spur gears, Vestn. Mashinostr., 1990, no. 11, pp. 18–20.
11. Airapetov, E.L., Genkin, M.D., and Ryasnov, Yu.A., Statika zubchatykh peredach (Statics of Gears), Moscow: Nauka, 1983.
12. Nakhatakyan, F.G., Contact stress and strain of cylinders in skewing, Russ. Eng. Res., 2011, vol. 31, no. 10, pp. 960–962. https://doi.org/10.3103/s1068798x1110018210.3103/s1068798x11100182 ↗
13. Nakhatakyan, F.G., Studying the stress–strain state of elastic elements of gear mechanisms and structures at their linear and edge contact, Doctoral (Eng.) Dissertation, Moscow: Mechanical Engineering Research Institute, Russian Academy of Sciences, 2014.
14. Kovalevskii, V.I., Development and theoretical substantiation of rational designs of spur bevel gears, Doctoral (Eng.) Dissertation, Tashkent, 1992.