journal article·2021-03

Size Determination of Abrasive Particles that Penetrate into the Wedge-Shaped Gap of Gear Teeth

H. K. Ishmuratov, K. H. Ishmuratova

Journal of Friction and Wear· Volume 42· Issue 2
Publisher page

Abstract

In this paper, we consider the movement of abrasive particles located in the wedge-shaped gap of gear teeth. These particles penetrate into the wedge-shaped gap between friction surfaces. In the event that the friction force between the abrasive particle and the friction surfaces is greater than the forces that prevent the penetration of the abrasive particle, which arises from the normal force, the abrasive particles are pressed against the friction surfaces. It was found that the largest size of abrasive particles that penetrate into the wedge-shaped gap of the gear teeth with an increase in the friction coefficient from 0.01 to 0.07 increases by more than 20 times while an increase in the meshing modulus from 0.001 to 0.025 m doubles in the presence of lubrication. It is proposed to consider the wear of gears as a process that occurs with the active and passive participation of abrasive particles. The wear of the gear teeth with the active participation of abrasive particles occurs in the wedge-shaped gap between the gear teeth at the frictional force of the surfaces before they are crushed. Wear with the passive participation of abrasive particles occurs in the contact zone of the gear teeth after crushing of abrasive particles due to the force interaction of the protrusions of the roughness of the friction surfaces.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Tribology and Wear Analysis · Engineering Technology and Methodologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (10)

Show source-provided references
1. Irgashev, B.A. and Irgashev, A.I., Forecasting the consumption of spare parts in machines based on the content of wear particles in oil, J. Frict. Wear, 2015, vol. 36, no. 5, pp. 441–447.10.3103/S1068366615050062 ↗
2. Ishmuratov, H.K., Theoretical substantiation of the resource of gears of cotton pickers according by the wear criterion, Doctoral (Eng.) Dissertation, Tashkent, 2019.
3. Irgashev, A.I., Increasing the wear resistance of heavy loaded gears of machine assemblies, Doctoral (Eng.) Dissertation, Tashkent, 2005.
4. Ishmuratov, K.K. and Irgashev, B.A., Assessment of the wear resistance for gearwheel teeth in an open toothed gear under the conditions of a high level of dust, J. Frict. Wear, 2020, vol. 41, no. 1, pp. 85–90.10.3103/S1068366620010092 ↗
5. Kragel’skii, I.V., et al., Osnovy raschetov na trenie i iznos (Basic Calculations for Friction and Wear), Moscow: Mashinostroenie, 1977.
6. Khachatur’yan, S.V., Negmatov, S.S., and Irgashev, A.I., The entropy balance of the abrasive wearing, Vestn. Tashk. Gos. Tekh. Univ., 2004, no. 3, pp. 28–32.
7. Sharipov, V.M., Konstruirovanie i raschet traktorov (Engineering and Calculation of Tractors), Moscow: Mashinostroenie, 2004
8. Yampol’skii, G.Ya. and Kragel’skii, I.V., Issledovanie abrazivnogo iznosa elementov par treniya kacheniya (Abrasive Wear of the Elements of Rolling Friction Pairs), Moscow: Nauka, 1973.
9. Yampol’skii, G.Ya. and Natarov, A.P., Calculation of abrasive wear of gear tooth, in Raschetnye metody otsenki treniya i iznosa (Calculation Methods for Assessment of Friction and Wear), Bryansk: Priokskoe Knizhn. Izd., 1975, pp. 189–204.
10. Reshchikov, V.F., Trenie i iznos tyazhelo-nagruzhennykh peredazh (Friction and Wear of Heavily Loaded Gears), Moscow: Mashinostroenie, 1975.