journal article·2013-06

Effect of Applied Load in the Nanoindentation of Gold Ball Bonds

Muhammad Nubli Zulkifli, Azman Jalar, Shahrum Abdullah, Irman Abdul Rahman, Norinsan Kamil Othman

Journal of Electronic Materials· Volume 42· Issue 6
Publisher page

Abstract

We have analyzed the effects of nanoindentation at applied loads of 10 mN and 20 mN on the micromechanical properties of gold (Au) ball bonds with and without cracks. The depth profile and the plastic zone size for each indentation were determined to identify the substrate effect and its relationship with the observed micromechanical properties. The substrate effect occurred for indentations at 20 mN applied load, but did not occur near cracks for either 10 mN or 20 mN loads. Because of the substrate effect and the presence of cracks, the average hardness or yield strength decreased for indentations on Au ball bonds. Therefore, to minimize the substrate effect, an applied load of 10 mN is best for characterizing Au ball bonds.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. C.D. Breach and F.W. Wulff, Microelectron. Reliab. 50, 1 (2010).10.1016/j.microrel.2009.08.003 ↗
2. G. Harman, Wire Bonding in Microelectronics (New York: McGraw-Hill, 2010), pp. 307–315.
3. R.R. Tummala, Fundamentals of Microsystems Packaging (New York: McGraw-Hill, 2001), pp. 311–312.
4. W.D.V. Driel, R.B.R.V. Silfhout, and G.Q. Zhang, Microelectron. Int. 25, 15 (2008).10.1108/13565360810875967 ↗
5. Z.W. Zhong, Microelectron. Int. 26, 10 (2009).
6. V. Sundaraman, D.R. Edwards, W.E. Subido, and H.R. Test, 50th Electronic Components and Technology Conf. (IEEE, Las Vegas, 2000), pp. 416–420.
7. G.G. Harman and C.A. Cannon, IEEE Trans. Compon. Hybrids Manuf. Technol. 3, 203 (1978).10.1109/TCHMT.1978.1135290 ↗
8. M. Petch, D. Barker, and P. Lall, IEEE Trans. Compon. Packag. Aging Manuf. Technol. 17, 610 (1994).10.1109/95.335048 ↗
9. Z.N. Liang, F.G. Kuper, and M.S. Chen, Microelectron. Reliab. 38, 1287 (1998).10.1016/S0026-2714(98)00093-6 ↗
10. R. Pantaleon, J. Sanchez-Mendoza, and M. Mena, 44th Electronic Components and Technology Conf. (IEEE Washington, DC, 1994) pp. 733–740.
11. S. Murali, N. Srikanth, and C.J. Vath III, Microelectron. Reliab. 46, 467 (2006).10.1016/j.microrel.2005.05.011 ↗
12. T. Saraswati, T. Sritharan, S. Mhaisalkar, C.D. Breach, and F. Wulff, Mater. Sci. Eng. A. 423, 14 (2006).10.1016/j.msea.2005.10.080 ↗
13. M. Shah, K. Zeng, A.A.O. Tay, and S. Suresh, J. Electron. Packag. 126, 87 (2002).10.1115/1.1648062 ↗
14. P.A. Agyakwa, M.R. Corfield, J.F. Li, W. Loh, E. Liotti, S.C. Hogg, and C.M. Johnson, IEEE Trans. Device Mater. Reliab. 10, 254 (2010).10.1109/TDMR.2010.2044796 ↗
15. A. Jalar, M.N. Zulkifli, and S. Abdullah, Adv. Mater. Res. 148–149, 1163 (2011).
16. W.C. Oliver and G.M. Pharr, J. Mater. Res. 7, 1564 (1992).10.1557/JMR.1992.1564 ↗
17. A.C. Fischer-Cripps, Introduction to Contact Mechanics (New York: Springer, 2000), pp. 1–81.
18. S. Murali, N. Srikanth, and C.J. Vath III, Mater. Charact. 50, 39 (2003).10.1016/S1044-5803(03)00102-5 ↗
19. N. Srikanth, S. Murali, Y.M. Wong, and C.J. Vath III, Thin Solid Films 462–463, 339 (2004).10.1016/j.tsf.2004.05.116 ↗
20. T.Y. Zhang and W.H. Xu, J. Mater. Res. 17, 1715 (2002).10.1557/JMR.2002.0254 ↗
21. S. Pahak, D. Stojakovic, R. Doherty, and S.R. Kalidindi, J. Mater. Res. 24, 1142 (2008).10.1557/jmr.2009.0137 ↗
22. W.D. Nix and H. Gao, J. Mech. Phys. Solids 46, 411–425 (1998).10.1016/S0022-5096(97)00086-0 ↗
23. R.K.A. Al-Rub, Mech. Mater. 39, 787 (2007).10.1016/j.mechmat.2007.02.001 ↗
24. G.Z. Voyiadjis and R. Peters, Acta Mech. 211, 131 (2010).10.1007/s00707-009-0222-z ↗
25. A.A. Elmustafa and D.S. Stone, Mater. Lett. 57, 1072 (2003).10.1016/S0167-577X(02)00933-3 ↗
26. K. Durst, B. Backes, and M. Goken, Scr. Mater. 52, 1093 (2005).10.1016/j.scriptamat.2005.02.009 ↗
27. D.R. Askeland and P.P. Pradeep, The Science and Engineering of Materials (Toronto: Thomson, 2006), pp. 39–42.
28. Y. Choi and S. Suresh, Scr. Mater. 48, 249 (2003).10.1016/S1359-6462(02)00377-9 ↗
29. Y. Choi, K.J.V. Vliet, J. Li, and S. Suresh, J. Appl. Phys. 94, 6050 (2003).10.1063/1.1615702 ↗
30. M. Dietiker, R.D. Nyilas, C. Solenthaler, and R. Spolenak, Acta Mater. 56, 3887 (2008).10.1016/j.actamat.2008.04.032 ↗
31. J. Lian, J. Wang, Y. Kim, and J. Greer, J. Mech. Phys. Solids. 57, 812 (2009).10.1016/j.jmps.2009.01.008 ↗
32. X.H. Wang, S. Jacobsen, J.Y. He, Z.L. Zhang, S.F. Lee, and H.L. Lein, Cem. Concr. Res. 39, 701 (2009).10.1016/j.cemconres.2009.05.002 ↗
33. A. Daugela, N. Gitis, and V. Gelfeindbein, Microsyst. Technol. 16, 33 (2010).10.1007/s00542-008-0733-x ↗
34. A. Bolshakov and G.M. Pharr, J. Mater. Res. 13, 1049 (1998).10.1557/JMR.1998.0146 ↗
35. W.C. Oliver and G.M. Pharr, J. Mater. Res. 19, 3 (2004).10.1557/jmr.2004.19.1.3 ↗
36. A.C. Fischer-Cripps, Surf. Coat. Technol. 200, 4153 (2006).10.1016/j.surfcoat.2005.03.018 ↗
37. A.C. Fischer-Cripps, J. Mater. Sci. 32, 727 (1997).10.1023/A:1018552222072 ↗