journal article·2001-08

Fluxless wetting propeities of one-side-coated under bump metallurgy and top surface metallurgy

Soon-Min Hong, Jae-Yong Park, Jae-Pil Jung, Choon-Sik Kang

Journal of Electronic Materials· Volume 30· Issue 8
Publisher page

Abstract

The wetting balance test was performed in an attempt to estimate the fluxless wetting properties of under bump metallurgy (UBM)-coated Si-wafer and top surface metallurgy (TSM)-coated glass substrate to SnPb solder. The wetting curves of the single-and double-side-coated UBM had a similar shape and the parameters characterizing the curve shape showed a similar tendency as a function of temperature. Wetting property estimation was possible with the new wettability indices from the wetting curves of one side-coated specimens; Fmin, Fs, and ts. Au/Cu/Cr UBM was better than Au/Ni/Ti UBM from the point of wetting time. For TSM, it was more effective to use Cu as a wetting layer with Au as a protection layer than to use Au as a wetting layer alone. The contact angle of one-side-coated Si-plate to SnPb solder can be calculated from the force balance equation by measuring static state force and tilt angle. The contact angles of Au/Cu/Cr and Au/Ni/Ti UBM of Si-wafer to SnPb solder were 59.9° and 63.9°, respectively. The contact angles of Au/Cu/Cr and Au/Cr TSM of glass to SnPb were 78.9 and 76.1°, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Electrical Contact Performance and Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. The Int. Technology Roadmap for Semiconductors, 1999 edition: Assembly and Packaging (San Jose, CA:SIA, 1999), p. 224.
2. Demand for Development of Industrial Technology Towards Year 2000, vol. 23 (Daejon, Korea: Korea Institute of Industrial Technology Evaluation and Planning, Demand, 1996), p. 139.
3. J. Lau ed.Flip Chip Technologies (New York: McGraw-Hill, 1995), p. 123.
4. P. T. Vianco,The Metal Science of Joining (Warrendale, PA: TMS, 1992), p. 265.
5. R. J. Wassink,Soldering in Electronics (Ary, Scotland: Electrochemical Soc., 1989), p. 300.
6. R. B. Cinique and J. W. Morris, Jr.,J. Electron. Mater. 23, 533 (1994).10.1007/BF02670656 ↗
7. L. M. Racz and J. Szekely,Adv. in Electron. Pkg. EEP-vol. 4–2 1103 (1993).
8. C. Lea and W. A. Dench,Soldering & Surface Mount Technol. 4, 14 (1990).10.1108/eb037702 ↗
9. A. D. Roming et al.,Solder Mechanics, ed. D. R. Frear et al. (Warrendale, PA: TMS, 1990), p. 36.
10. J. Y. Park (Doctoral Thesis, Seoul National University, Seoul, 2000).
11. H. K. Kim, H. K. Liou, and K. N. Tu,J. Mater. Res. 10, 497 (1995).10.1557/JMR.1995.0497 ↗
12. H. H. Manko,Solders and Soldering (New York: McGraw-Hill, 1979), p. 313.
13. W. Lin and Y.C. Lee,IEEE Trans. on Adv. Pkg. 22, 592 (1999).10.1109/6040.803451 ↗
14. W. Moeller and D. Knoedler,Verbindungstechnik in der Elektnonik (March 1992), p. 14.
15. F. Masahiko et al.,Proc. of Electronic Components and Technology Conf. (New York: IEEE-CPMT, 1999),p. 408.