journal article·2006-05

Temperature and current-density distributions in flip-chip solder joints with Cu traces

C. Y. Hsu, D. J. Yao, S. W. Liang, Chih Chen, Everett C. C. Yeh

Journal of Electronic Materials· Volume 35· Issue 5
Publisher page

Abstract

Three-dimensional simulation was performed to investigate the temperature and current density distribution in flip-chip solder joints with Cu traces during current stressing. It was found that the Cu traces can reduce the Joule heating effect significantly at high stressing currents. When the solder joints were stressed by 0.6 A, the average temperature increases in solder bumps with the Al traces was 26.7°C, and it was deceased to 18.7°C for the solder joint with the Cu traces. Hot spots exist in the solder near the entrance points of the Al or Cu traces. The temperature increases in the hot spot were 29.3°C and 20.6°C, for solder joints with the Al traces and Cu traces, respectively. As for current density distribution, the maximum current density inside the solder decreased slightly from 1.66×105 A/cm2 to 1.46×105 A/cm2 when the Al traces were replaced by the Cu traces. The solder joints with the Cu traces exhibited lower Joule heating and current crowding effects than those with the Al traces, which was mainly attributed to the lower electrical conductivity of the Cu traces. Therefore, the solder joints with the Cu traces are expected to have better electromigration resistance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. International Technology Roadmap for Semiconductors (San Jose, CA: Assembly and Packaging Section, Semiconductor Industry Association, 2003), pp. 4–9.
2. K.N. Tu,J. Appl. Phys. 94, 5451 (2003).10.1063/1.1611263 ↗
3. S. Brandenburg and S. Yeh,Proc. Surface Mount Int. Conf. Exhib. (Edina, MN: SMTA, 1998), p. 337–344.
4. C.Y. Liu, C. Chen, C.N. Liao, and K.N. Tu,Appl. Phys. Lett. 75, 58 (1999).10.1063/1.124276 ↗
5. H. Ye, C. Basaran, and D. Hopkins,Appl. Phys. Lett. 82, 7 (2003).10.1063/1.1534936 ↗
6. J.D. Wu, P.J. Zheng, K. Lee, C.T. Chiu, and J.J. Lee,Electronic Components and Technology Conf. (Piscataway, NJ: IEEE, 2002), p. 452–457.
7. J.W. Nah, K.W. Paik, J.O. Suh, and K.N. Tu,J. Appl. Phys. 94, 7560 (2003).10.1063/1.1628388 ↗
8. J.R. Black,IEEE Trans. Electron Dev. ED-16, 338 (1969).10.1109/T-ED.1969.16754 ↗
9. C. Everett, C. Yeh, W.J. Choi, and K.N. Tu,Appl. Phys. Lett. 80, 4 (2002).10.1063/1.1430852 ↗
10. T. L. Shao, S.W. Liang, T. C. Lin, and C. Chen,J. Appl. Phys., to be published (1985).
11. T.L. Shao, S.H. Chiu, C. Chen, D.J. Yao, and C.Y. Hsu,J. Electron. Mater. 33, 1350 (2004).10.1007/s11664-004-0164-0 ↗
12. R. Tummala,Fundamentals of Microsystem Packaging (New York: McGraw-Hill, 2001), p. 225.