journal article·2003-12

Electromigration studies on Sn(Cu) alloy lines

C. C. Lu, S. J. Wang, C. Y. Liu

Journal of Electronic Materials· Volume 32· Issue 12
Publisher page

Abstract

The Cu alloying effect in the Sn(Cu) solder line has been studied. The Sn0.7Cu solder line has the most serious electromigration (EM) damage compared to pure Sn and Sn3.0Cu solder lines. The dominant factor for the fast EM rate in Sn0.7Cu could be attributed to the relatively small grain size and the low critical stress, i.e., the yielding stress of the Sn0.7Cu solder line. Also, we found that the shortest Sn0.7Cu solder line, 250 μm, has the most serious EM damage among three solder lines of different lengths. The back stress induced by EM might not play a significant role on the EM test of long solder lines. A new failure mode of EM test was observed; EM under an external tensile stress. The external stress is superimposed on the stress profile induced by EM. As a result, the hillock formation was retarded at the anode side, and void formation was enhanced at the cathode.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · Copper Interconnects and Reliability · 3D IC and TSV technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. Semiconductor Industry Association, The National Technology Roadmap for Semiconductors (San Jose, CA: Semiconductor Industry Association, 1997), pp. 10–15.
2. J.H. Lau, Flip Chip Technologies (New York: McGraw-Hill, 1996), pp. 26–30.
3. S. Brandenberg and S. Yeh, SMI 98 Proc. (Edina, MN: Surface Mount Technology Association, 1998), pp. 337–344.
4. T.Y. Lee and K.N. Tu, J. Appl. Phys. 90, 4502 (2001).10.1063/1.1400096 ↗
5. T.Y. Lee, K.N. Tu, S.M. Kuo, and D.R. Frear, J. Appl. Phys. 89, 3189 (2001).10.1063/1.1342023 ↗
6. Q.T. Huynh, C.Y. Liu, C. Chen, and K.N. Tu, J. Appl. Phys. 89, 4332 (2001).10.1063/1.1357459 ↗
7. C.Y. Liu, C. Chen, C.N. Liao, and K.N. Tu, Appl. Phys. Lett. 75, 58 (1999).10.1063/1.124276 ↗
8. H.B. Huntington, Diffusion in Solids: Recent Developments, ed. A.S. Nowick and J.J. Burton (New York: Academic Press, 1979), pp. 303–352.
9. A. Gangulee and F.M. d’Heurle, Thin Solid Films 16, 227 (1973).10.1016/0040-6090(73)90171-5 ↗
10. J.R. Lloyd and J.J. Clement, Appl. Phys. Lett. 69, 2486 (1996).10.1063/1.117506 ↗
11. J. van Ek, J.P. Dekker, and A. Lodder, Phys. Rev. B 52, 8794 (1995).10.1103/PhysRevB.52.8794 ↗
12. I.A. Blech, J. Appl. Phys. 47, 1203 (1976).10.1063/1.322842 ↗
13. R. Rosenberg, J. Vac. Sci. Technol. 9, 289 (1972).10.1116/1.1316576 ↗
14. J. Madeni, S. Liu, and T. Siewert, Material Solutions; Joining Advanced Specialty Materials IV (Materials Park, OH: ASM International, 2001), pp. 33–38.
15. Welco Castings, Solder Data Sheet (Ontario, Canada: Welco Castings).
16. D.R. Frear, S.N. Burchett, H.S. Morgan, and J.H. Lan, eds., The Mechanics of Solder Alloy Interconnects (New York: Van Nostrand Reinhold, 1994), pp. 60–67.
17. D.E. Gray, ed., American Institute of Physics Handbook (New York: McGraw-Hill, 1957), pp. 2–61 ff.
18. K.L. Lee, C.K. Hu, and K.N. Tu, J. Appl. Phys. 78, 4428 (1995).10.1063/1.359851 ↗
19. C.Y. Liu and K.N. Tu, unpublished results.