Effect of burn-in on shear strength of 63Sn-37Pb solder joints on an Au/Ni/Cu substrate
Source abstract
Abstract
A study was performed to examine the effect of burn-in and Au-plating thickness on the shear strength of 63Sn-37Pb solder joints in ball grid array (BGA) packages. The Au-plating thicknesses of 0.3 µm, 0.6 µm, 0.9 µm, and 1.4 µm were evaluated. An isothermal aging temperature of 150°C was employed to simulate burn-in conditions. The evolution of the bulk solder microstructure and intermetallic compounds at the solder joint interface were characterized and correlated to the measured shear strength. The strength of the solder joints with 0.3-µm Au plating was approximately three times higher than the thicker platings after aging. Solder joints with 0.3-µm Au plating failed within the solder matrix, and their strength was dependent upon the bulk solder microstructure and composition. The weakness of the solder joints with thicker Au platings was attributed to the formation of a brittle AuSn4/Ni3Sn4 interface and a ductile Pb-rich layer at the interface.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Electrical Contact Performance and Analysis · 3D IC and TSV technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. C.J. Thwaites, Electroplat. Met. Finish. 26, 21 (1973).
2. J. Ciulik and M.R. Notis, Proc. 2nd ASM Int. Electronic Materials and Processing Congr., PA, 1989 (Materials Park, OH: ASM International), pp. 57–61.
3. G.S. Matijasevic, C.C. Lee, and C.Y. Wang, Thin Solid Films 223, 276 (1993).10.1016/0040-6090(93)90533-U ↗
4. C.J. Thwaites, Int. Met. Rev. 29, 45 (1984).10.1179/imr.1984.29.1.45 ↗
5. S.K. Kang and V. Ramachandran, Scripta Metall. 14, 421 (1980).10.1016/0036-9748(80)90338-5 ↗
6. H.D. Blair, T.Y. Pan, and J.M. Nicholson, Proc. Electronic Components and Technology Conf. 1998 (Seattle, WA: IEEE and TMS) pp. 259–267.
7. W.G. Bader, Weld. Res. Suppl., p. 551s (1969).
8. T.B. Massalski, Binary Alloy Phase Diagram (Materials Park, OH: ASM International, 1990), pp. 433–434.
9. K. Banerji and R.F. Darveaux, Microstructures and Mechanical Properties of Aging Material, ed. P.K. Liaw, R. Visvanathan, K.L. Murty, E.P. Simonen, and D.R. Frear (Warrendale, PA: TMS, 1993), pp. 431–442.
10. P.T. Vianco, J.J. Stephens, and J.A. Rejent, IEEE Trans. Comp., Hyb., Manu. Tech. Part A 20, 478 (1997).10.1109/95.650938 ↗
11. L. Buene, H. Falkenberg-Arell, and J. Tafto, Thin Solid Films 67, 95 (1980).10.1016/0040-6090(80)90292-8 ↗
12. H.P. Kehrer and E.M. Wenzel, Metall 33, 1047 (1979).