Investigating the Effects of Lead Forming Parameters on Intermetallic Layer Crack Using the Finite-Element Method
Source abstract
Abstract
The lead trim-and-form process is important in the manufacturing of programmable logic devices, microprocessors, and memories. Normally, inspection of a chip package is performed in a lead inspection machine after the lead forming process to detect defects on the leads. One such defect is the lead intermetallic compound (IMC) crack, exhibiting itself as plating crack. In this study, IMC crack of package leads, which causes loose connection between the copper lead and the tin plating, was analyzed using the finite-element method. The simulation results were verified by matching the simulated and actual formed lead profile. Simulation results showed a strong correlation between IMC crack after forming and aging and high residual tensile strain induced during lead forming. A proposal was made to resolve the crack issue by performing design of experiment (DOE) to reduce the residual tensile strain of the lead upon forming. Three optimization parameters were chosen, namely the forming angle, the shank angle, and the pre-forming angle. It is shown that, with the optimized parameter setting, a reduction of the residual strain can be achieved, thus minimizing the risk of IMC crack.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. A. Visser and M. Buhler, J. Mater. Process. Technol. 115, 108 (2001).10.1016/S0924-0136(01)00751-8 ↗
2. A.J. Babecki, Problems with Pure Tin Coating (NASA Materials Engineering Branch Publication No. 021, 2002). http://code541.gsfc.nasa.gov/Uploads_materials_tips_PDFs/TIP%20021R.pdf . Accessed 14 December 2010.
3. C.C. Wei, P.C. Liu, C. Chen, J.C.B. Lee, and I.P. Wang, J. Appl. Phys. 102, 043521 (2007).10.1063/1.2770832 ↗
4. P. Su, M. Ding, and S. Chopin, Proc. 55th Electron. Compon. and Technol. Conf. (Florida, May 2005), p. 434.
5. M. Dittes, Proc. Electron. Circuit World Conv., Vol. 9 (Cologne 2002).
6. MicroJoining Solutions—MicroTips™, Micro Joining Plating Issues (MicroTip Plating Issues, 2005). http://www.microjoining.com/microTip_Library/microTip_Plating%20Issues.pdf . Accessed 12 May 2010.
7. M. Ding, P. Su, and S. Chopin, Proc. 55th Electron. Compon. and Technol. Conf. (Florida, May 2005), p. 452.
8. L.M. Sim and Y. Chen, SIMTech Tech. Rep. 8, 202 (2007).
9. T.F. Lam, Proc. 9th IPFA 2002 (Singapore, 2002), p. 47.10.1142/S0217590802000432 ↗
10. Q. Qian, Y. Liu, Y. Liu, H. Yang, and S. Irving, 6th Int. Conf. on Electron. Packag. Technol. (2005).
11. Y.-L. Kang, H.-W. Wang, Z.-F. Zhang, and Q.-H. Qin, Microscopic Experimental Analysis of Fracture Toughness in Fracture of Copper Foils. http://www.icf11.com/proceeding/EXTENDED/5747.pdf . Accessed 18 October 2010.
12. ABAQUS HTML Documentation (Dassault Systemes, 2009).
13. SIP Hall Sensors Short Form—Rev 3.1, Application of SIP Hall Sensors: Lead Trimming and Forming Recommendations, MLX Trim&Form Guide (2008). http://www.melexis.com/Asset/Trim-and-form-recommendations-DownloadLink-5565.aspx . Accessed 12 April 2010.