Effects of Reflow Profile and Miniaturisation on the Integrity of Solder Joints in Surface Mount Chip Resistors
Source abstract
Abstract
Integrity of solder joints of components in an electronic device is critical to the device reliability. Miniaturisation manufacturing trend in electronic products development has continued to challenge the shear strength of the solder joints in these devices and necessitates implementation of optimal reflow profile to achieve maximum strength of the joints. This research proposes optimal parameter combination of reflow profile factors which demonstrate potential of delivering maximum shear strength of solder joint. The Taguchi design of experiment (DoE) is employed to generate eight orthogonal array designs of L24 of reflow profiles. The factors/parameters investigated are preheat gradient, time above liquidus (TAL), peak temperature and cooling rate. Three test vehicles of varying solder joint sizes are made from R1206, R0805 and R0603 resistors. Reflow profile number 3 constituting 1.2 °C/s preheat, 45 s TAL, 245 °C peak temperature and 60% cooling rate is optimal because it yielded joints with highest strength and circa 4 µm thickness of intermetallic compound (IMC). Solder joint shear strength decreases with decrease in size of lead-free joint irrespective of reflow profile implemented. These results will be useful to electronic packaging and reliability engineers faced with challenges of improving device operational mechanical performance in the continuing product miniaturisation trend.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. P. Lall, K. Goyal, K. Schulze, and S. Miller, Low-temperature solder interconnection of surface mount devices with additively printed pads on flexible substrate, in The 20th IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (iTherm) (2021), pp. 972–980.10.1109/ITherm51669.2021.9503253 ↗
2. N. Graddage, Components and devices, in Flexible, Wearable, and Stretchable Electronics, ed. by K. Sakuma (CRC Press, Boca Raton, 2020), pp. 59–10610.1201/9780429263941-3 ↗
3. A. Belous and V. Saladukha, Packaging technologies for electronic devices, High-Speed Digital System Design. (Cham: Springer, 2020), pp. 655–701.10.1007/978-3-030-25409-4_8 ↗
4. J.E. Njoku A Study of the Thermomechanical Reliability of Solder Joints in Surface Mount Electronics Technology (Doctoral dissertation, University of Greenwich) (2016).
5. N. Lee, Optimising the reflow profile via defect mechanism analysis. Solder. Surf. Mt. Technol. 11(1), 13–20 (2006).10.1108/09540919910254642 ↗
6. O.T. Kuttiyil Thomas and P.P. Gopalan, in Electronics Production Defects and Analysis (Springer, Singapore, 2022), eBook, page count 140.10.1007/978-981-16-9824-8 ↗
7. C.S. Lau, C.Y. Khor, D. Soares, J.C. Teixeira, and M.Z. Abdullah, Thermo-mechanical challenges of reflowed lead-free solder joints in surface mount components: a review. Solder. Surf. Mt. Technol. 28(2), 41–62 (2016).10.1108/SSMT-10-2015-0032 ↗
8. C. Lee, I. Lee, S. Jung, and C. Shur, Effect of surface finishes on ball shear strength in BGA joints with Sn-3.5 mass% Ag solder. Mater. Trans. 43(4), 751–756 (2002).10.2320/matertrans.43.751 ↗
9. C. Beddingfield, and L.M. Higgins, Effects of flux materials on the moisture sensitivity and reliability of flip-chip-on-board assemblies. IEEE Trans. Compon. Packag. Manuf. Technol. Part C 21(3), 189–195 (1998).10.1109/3476.720416 ↗
10. O.S. Salih, H. Ou, X. Wei, and W. Sun, Microstructure and mechanical properties of friction stir welded AA6092/SiC metal matrix composite. Mater. Sci. Eng. A 742, 78–88 (2019).10.1016/j.msea.2018.10.116 ↗
11. J. Górka and S. Stano, Microstructure and properties of hybrid laser arc welded joints (laser beam-MAG) in thermo-mechanical control processed S700MC steel. Metals 8(2), 132 (2018).10.3390/met8020132 ↗
12. U. Kumar, D.K. Gope, J.P. Srivastava, S. Chattopadhyaya, A.K. Das, and G. Krolczyk, Experimental and numerical assessment of temperature field and analysis of microstructure and mechanical properties of low power laser annealed welded joints. Materials 11(9), 1514 (2018).10.3390/ma11091514 ↗
13. M.R. Harrison, J.H. Vincent, and H.A. Steen, Lead-free reflow soldering for electronics assembly. Solder. Surf. Mt. Technol. 13(3), 21–38 (2001).10.1108/09540910110407388 ↗
14. E.B. Romdhane, P. Roumanille, A. Guédon-Gracia, S. Pin, P. Nguyen, and H. Frémont, Evaluation of SAC solder joint thermomechanical fatigue in different types of components, in 2022 23rd International Conference on Thermal, Mechanical and Multi-physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE) (IEEE, 2022), pp. 1–6.10.1109/EuroSimE54907.2022.9758868 ↗
15. Y. Lai, K. Pan, J. Xu, J. Yang, and S. Park, Determination of smarter reflow-profile to achieve a uniform temperature throughout aboard, in 2021, 20th IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (iTherm) (IEEE, 2021), pp. 911–916.10.1109/ITherm51669.2021.9503258 ↗
16. Y. Lai, K. Pan, C. Cai, P. Yin, J. Yang, and S. Park, Smarter temperature setup for reflow oven to minimise temperature variation among components. IEEE Trans. Compon. Packag. Manuf. Technol. 12(3), 562–569 (2022).10.1109/TCPMT.2022.3153952 ↗
17. J. Pan, T. Chou, J. Bath, D. Willie, and B.J. Toleno, Effects of reflow profile and thermal conditioning on intermetallic compound thickness for SnAgCu soldered joints. Solder. Surf. Mt. Technol. 21(4), 32–37 (2009).10.1108/09540910910989411 ↗
18. J. Webster, J. Pan, and B. Toleno, Investigation of the lead-free solder joint shear performance. J. Microelectron. Electron. Packag. 4(2), 72 (2007).10.4071/1551-4897-4.2.72 ↗
19. P. Wild, D. Lorenz, T. Grözinger, and A. Zimmermann, Effect of voids on thermo-mechanical reliability of chip resistor solder joints: experiment, modelling and simulation. Microelectron. Reliab. 85, 163–175 (2018).10.1016/j.microrel.2018.04.014 ↗
20. D. Lu, and C.P. Wong, in Materials for Advanced Packaging, ed. by D. Lu, C.P. Wong (2017) pp. 421–468.10.1007/978-3-319-45098-8_10 ↗
21. Y. Li, D. Lu, and C.P. Wong, Isotropically conductive adhesives (ICAs). Electric. Conduct. Adhesives Nanotech. 121–225 (2010).10.1007/978-0-387-88783-8_4 ↗
22. S. Nurmi, J. Sundelin, E. Ristolainen, and T. Lepistö, The effect of solder paste composition on the reliability of SnAgCu joints. Microelectron. Reliab. 44(3), 485–494 (2004).10.1016/j.microrel.2003.08.004 ↗
23. M. Ekpu, R. Bhatti, M.I. Okereke, S. Mallik, and K.C. Otiaba, Prediction and optimisation of design parameters of microelectronic heat sinks. J. Emerg. Trends Eng. Appl. Sci. (JETEAS) 4(3), 493–500 (2013).
24. E.H. Amalu, N.N. Ekere, M.T. Zarmai, and G. Takyi, Optimisation of thermo-fatigue reliability of solder joints in surface mount resistor assembly using Taguchi method. Finite Elem. Anal. Des. 107, 13–27 (2015).10.1016/j.finel.2015.08.004 ↗
25. R. Pundir, G.H.V.C. Chary, and M.G. Dastidar, Application of the Taguchi method for optimising the process parameters for removing copper and nickel by growing Aspergillus sp. Water Resour. Ind. 20, 83–92 (2018).10.1016/j.wri.2016.05.001 ↗
26. B.M. Girish, B.M. Satish, and S. Sarapure, Optimisation of wear behaviour of magnesium alloy AZ91 hybrid composites using Taguchi experimental design. Metall. Mater. Trans. A 47(6), 3193–3200 (2016).10.1007/s11661-016-3447-1 ↗
27. H. Wang, X. Hu, and X. Jiang, Effects of Ni modified MWCNTs on the microstructural evolution and shear strength of Sn-3.0 Ag-0.5 Cu composite solder joints. Mater. Charact. 163, 110287 (2020).10.1016/j.matchar.2020.110287 ↗
28. S.W. Chen, S.K. Lin, and J.M. Jao, Electromigration effects upon interfacial reactions in flip-chip solder joints. Mater. Trans. 45(3), 661–665 (2004).10.2320/matertrans.45.661 ↗
29. H.D. Blair, T. Pan, and J.M. Nicholson, Intermetallic compound growth on Ni, Au/Ni, and Pd/Ni substrates with Sn/Pb, Sn/Ag, and Sn solders [PWBs], in 48th Electronic Components & Technology Conference (IEEE, 1998), pp. 259–26710.1109/ECTC.1998.678704 ↗
30. L. Sun, L. Zhang, S.J. Zhong, J. Ma, and L. Bao, Reliability study of industry Sn3.0Ag0.5Cu/Cu lead-free soldered joints in electronic packaging. J. Mater. Sci. Mater. Electron. 26(11), 9164–9170 (2015).10.1007/s10854-015-3606-y ↗
31. Y. Chen, Z.C. Meng, L.Y. Gao, and Z.Q. Liu, Effect of Bi addition on the shear strength and failure mechanism of low-Ag lead-free solder joints. J. Mater. Sci. Mater. Electron. 32(2), 2172–2186 (2021).10.1007/s10854-020-04982-4 ↗
32. D. Straubinger, A. Géczy, A. Sipos, A. Kiss, D. Gyarmati, O. Krammer, D. Rigler, D. Bušek, and G. Harsányi, Advances on high current load effects on lead-free solder joints of SMD chip-size components and BGAs. Circuit World. 45(1), 37–44 (2019)10.1108/CW-11-2018-0088 ↗
33. Y. Wang, X. Zhao, X. Xie, Y. Gu, and Y. Liu, Effects of nano-SiO2 particles addition on the microstructure, wettability, joint shear force and the interfacial IMC growth of Sn3.0Ag0.5Cu solder. J. Mater. Sci. Mater. Electron. 26(12), 9387–9395 (2015).10.1007/s10854-015-3151-8 ↗
34. V. Wirth, K. Rendl and F. Steiner, Effect of multiple reflow cycles on intermetallic compound creation, in 2015 38th International Spring Seminar on Electronics Technology (ISSE) (IEEE, 2015) pp. 226–23010.1109/ISSE.2015.7247995 ↗
35. W.H. Zhong, Y.C. Chan, M.O. Alam, B.Y. Wu, and J.F. Guan, Effect of multiple reflow processes on the reliability of ball grid array (BGA) solder joints. J. Alloys Compd. 414(1–2), 123–130 (2006).10.1016/j.jallcom.2005.07.047 ↗
36. M. Arra, D. Shangguan, E. Ristolainen, and T. Lepistö, Effect of reflow profile on wetting and intermetallic formation between Sn/Ag/Cu solder components and printed circuit boards. Solder. Surf. Mt. Technol. 14(2), 18–25 (2002).10.1108/09540910210427781 ↗