journal article·2021-08

Impact of Thermal Cycling on Cu Press-Fit Connector Pin Interconnect Mechanical Stability

Yeon-Jin Baek, Aruna Palaniappan, Greg Baty, Li Li, Seung-Kyun Hyun, Tae-Kyu Lee

Journal of Electronic Materials· Volume 50· Issue 8
Publisher page

Abstract

Press-fit technology provides an electrical and mechanical connection by inserting a press-fit pin into a through-hole of a printed circuit board (PCB). Recently, there has been a wide interest in the long-term reliability of the press-fit pin interconnect of electric systems under various thermo-mechanical conditions due to the integration and minimization of electric devices. Compared to a ball grid array (BGA) interconnection, press-fit pin connector interconnects are expected to have a different degradation mechanism. In this study, the impact factors affecting reliability and degradation mechanism of press-fit connector pins were investigated. The bonding strength of inserted pins was measured before and after thermal cycling at room temperature and elevated temperature conditions. It is observed that the bonding strength of the press-fit pins to the PCB Cu wall increased after thermal cycling. The development of an intermetallic compound between the Cu pin and the Cu wall is observed. The microstructure of the press-fit connector pin and the Cu wall and localized stress and strain levels were analyzed by electron backscattered diffraction including inverse pole figure maps, grain reference orientation deviation maps, and strain contouring maps. Along with the increase of pull strength after thermal cycling, an increase in residual stresses was observed while strain contouring maps exhibited a decrease in localized strains at the interface between a press-fit pin and copper wall of a PCB.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · Integrated Circuits and Semiconductor Failure Analysis · 3D IC and TSV technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. S. Hong, Memory technology trend and future challenges, in 2010 International Electron Devices Meeting Proceedings, 12.4.1 (2010)10.1109/IEDM.2010.5703348 ↗
2. B. Mutnury, M. Cases, Nam Pham, D. N. de Araujo, E. Matoglu, P. Patel, and B. Hermann, Analysis of fully buffered DIMM interface in high-speed server applications, in IEEE Proceedings 56th Electronic Components and Technology Conference, vol. 6 (2006)
3. A. Makarov, V. Sverdlov, and S. Selberherr, Microelectron. Reliab. 52, 628 (2012).10.1016/j.microrel.2011.10.020 ↗
4. J. Scaminaci, IEEE Trans. Manuf. Technol. 6, 23 (1977).10.1109/TMFT.1977.1136231 ↗
5. Y. Nomura, Y. Saitoh, K. Furukawa, Y. Minami, K. Horiuchi, and Y. Hattori, Press-fit connector for automobile ECUs, in electrical contacts, in Proceedings of the 52nd IEEE Holm Conference on Electrical Contacts, vol. 211 (2006)10.1109/HOLM.2006.284089 ↗
6. L. Miller, Analysis of compliant pins subjected to plastic deformation, Master degree thesis, Rochester Institute of Technology (1986)
7. M.S. Jellesen, D. Minzari, U. Rathinavelu, P. Møller, and R. Ambat, Eng. Fail. Anal. 17, 1263 (2010).10.1016/j.engfailanal.2010.02.010 ↗
8. K. N. Tu and K. Zeng, Reliability issues of Pb-free solder joints in electronic packaging technology, in Proceedings 52nd Electronic Components and Technology Conference, vol. 1194 (2002)
9. H. Tohmyoh, K. Yamanobe, M. Saka, J. Utsunomiya, T. Nakamura, and Y. Nakano, J. Electron. Packag. 130, 031007 (2008).10.1115/1.2957330 ↗
10. A. Palaniappan, L. Li, and T. Lee, Impact of press-fit connector pin microstructure elastic response to PCB through-hole Cu wall interface long-term contact reliability, in 2018 IEEE 20th Electronics Packaging Technology Conference (EPTC) Proceedings, vol. 890 (2018)10.1109/EPTC.2018.8654324 ↗
11. T. Kanai, Y. Ando, and S. Inagaki, IEEE Trans. Compon. Hybrids Manuf. Technol. 8, 40 (1985).10.1109/TCHMT.1985.1136458 ↗
12. T. Manninen, K. Kanervo, A. Revuelta, J. Larkiola, and A.S. Korhonen, Mater. Sci. Eng. A 460–461, 633 (2007).10.1016/j.msea.2007.01.125 ↗
13. R. Wang, and L. Xu, Reliability 116, 114010 (2021).
14. S.I. Wright, M.M. Nowell, and D.P. Field, Microsc. Microanal. 17, 316 (2011).10.1017/S1431927611000055 ↗
15. L.N. Brewer, D.P. Field, and C.C. Merriman, Mapping and assessing plastic deformation using EBSD, Electron Backscatter Diffraction in Materials Science. ed. A.J. Schwartz, M. Kumar, B.L. Adams, and D.P. Field (US, Boston, MA: Springer, 2009), pp. 251–262.10.1007/978-0-387-88136-2_18 ↗
16. L.N. Brewer, M.A. Othon, L.M. Young, and T.M. Angeliu, Microsc. Microanal. 12, 85 (2006).10.1017/S1431927606060120 ↗
17. A.J. Wilkinson, and T. Ben, Mater. Today 15, 366 (2012).10.1016/S1369-7021(12)70163-3 ↗