ENIG Corrosion Induced by Second-Phase Precipitation
Source abstract
Abstract
Materials analysis of a flip-chip package lot with solder bump interconnect failures revealed a new mechanism for corrosion of electroless nickel immersion gold surface finish. Detailed scanning and transmission electron microscopy (SEM and TEM) in conjunction with focused ion beam microscopy and electron dispersion analysis of the unsoldered ball grid array substrate pads on packages that exhibited flip-chip solder bump interconnect failures revealed an unusual and subtle defect in the original Ni(P) layer, which was ultimately responsible for flip-chip joint failure. Detailed TEM analysis of the defect regions showed that they consisted of Ni(P) particles of slightly different composition than the bulk Ni(P) layer. Microstructure changes around these incorporated particles indicated that the second-phase particles were deposited from the plating bath during the Ni(P) growth stage. The second-phase particles provided additional surface area for nucleation and growth of Ni(P). Ultimately, a low-density boundary region in the growing Ni(P) layer formed where the particle-induced growth front and the planar Ni(P) film growth front intersected. This low-density interface eventually terminated at the surface of the Ni(P) layer. In addition the growth from the second-phase particle created localized surface topology that was different than that of the surrounding Ni(P) layer. The low-density interfaces as well as the surface topology led to enhanced corrosion of the Ni(P) layer when exposed to the immersion gold plating process. In some cases the corrosion was severe enough to create voids in the Ni(P) layer. The exposed, oxidized Ni(P) surfaces in and around these enhanced corrosion regions did not wet when exposed to solder. This led to degradation in the strength of the solder joint and subsequent solder interconnect failure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Non-Destructive Testing Techniques · Welding Techniques and Residual Stresses · Electronic Packaging and Soldering Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (11)
Show source-provided references
1. T.I. Eijim, D.B. Hollesen, A. Holliday, S.A. Gahr, and R.J. Coyle, Proceedings of the 21st IEEE International Electronics Manufacturing Symposium (1997), pp. 25–31.
2. C.H. Zhong and S. Yi, Solder. Surf. Mt. Technol. 11, 44 (1999).10.1108/09540919910254930 ↗
3. Y.-C. Sohn, J. Yu, S.K. Kang, D.-Y. Shih, and T.-Y. Lee, Proceedings of the 55th Electronics Components and Technology Conference (2005), pp. 83–91.
4. K. Zeng, R. Stierman, D. Abbott, and M. Murtuza, J. Electron. Mater. 58, 75 (2006).
5. G.M. Wenger, R.J. Coyle, P.P. Sloan, J.K. Dorey, C.V. Dodd, R. Erich, and A. Primavera, Proceedings of the 26th International Symposium for Testing and failure Analysis (2000), pp. 355–366.
6. R.J. Coyle, D.E.H. Popps, A. Mawer, D.P. Cullen, G.M. Wenger, and P.P. Solan, IEEE Trans. Compon. Packag. Technol. 26, 724 (2003).10.1109/TCAPT.2003.821694 ↗
7. N. Biunno, Proceedings of the IPC Printed Circuits Expo. S18 (1999), pp. 561–568.
8. Z. Mei, M. Kauffmann, A. Eslamnolchi, and P. Johnson, 48th Electronics Components and Technology Conference (1998), pp. 952–961.
9. D. Goyal, T. Lane, P. Kinzie, C. Oanichas, K.M. Chong, and O. Villalobos, Proceedings of the 52nd Electronics Components and Technology Conference (2002), pp. 732–739.
10. Y.-C. Sohn and J. Yu, J. Mater. Res. 20, 1931 (2005).10.1557/JMR.2005.0246 ↗
11. K. Zeng, Proceedings of the 6th Ann. Topical Research Conf., SEMATECH (October 27–28, 2003).