Thermal and Mechanical stability of electrically conductive adhesive joints
Source abstract
Abstract
Post curing of electrically conductive adhesives (silver filled epoxy) by heating at an elevated temperature significantly enhances the thermal and mechanical stability of conductive adhesive joints. The contact electrical resistivity and thickness of a joint with epoxy or silicone based adhesive tend to decrease cycle to cycle upon thermal cycling between 30°C and 50°C and upon compression (up to 0.55 MPa), except for the silicone joint in the absence of compression. The effect of compression is significant in epoxy joint without post curing and in silicone joint, but is insignificant in epoxy joint after post curing, The effect of thermal cycling is significant in epoxy joint without post curing, less significant in silicone joint, and insignificant in epoxy joint after post curing.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. S.K. Kang and S. Purushothaman, J. Electron. Mater. 28, 1314 (1999).10.1007/s11664-999-0173-0 ↗
2. D. Lu, Q.K. Tong, and C.P. Wong, IEEE Trans. Electron. Packaging Manufacturing 22, 223 (1999).10.1109/6104.795857 ↗
3. T. Inada and C.P. Wong, Proc. 1998 4th Int. Symp. Exhib. on Advanced Packaging Materials, Properties & Interfaces (1998), pp. 268–271.
4. K.-D. Kim and D.D.L. Chung, J. Electron. Mater. 31, 933 (2002).10.1007/s11664-002-0186-4 ↗
5. T.W. Giants, J. Adh. Sci. Technol. 12, 593 (1998).10.1163/156856198X00812 ↗
6. K. Feldmann and R. Luchs, Surface Mount Technol. 12, 74 (1998).
7. C.P. Wong, D. Lu, L. Meyers, S.A. Vona, Jr., and Q.K. Tong, Proc. 1997 1st IEEE Int. Symp. on Polymeric Electronics Packaging (Piscataway, NJ: IEEE, 1997), pp. 80–85.
8. M. Zwolinski, J. Hickman, H. Rubin, Y. Zaks, S. McCarthy, T. Hanlon, P. Arrowsmith, A. Chaudhuri, R. Hermansen, S. Lau, and D. Napp, IEEE Trans. Components, Packaging, Manufacturing Technol. Part C: Manufacturing 19, 241 (1996).10.1109/3476.558550 ↗
9. K.F. Schoch, Jr. and A.I. Bennett, Proc. 17th Electrical/Electronics Insulation Conf. (Piscataway, NJ: IEEE Service Center, 1985), pp. 291–293.
10. M.A. Lutz and R.L. Cole, 39th Electronic Components Proc.-Electronic Components Conf. (Piscataway, NJ: IEEE Service Center, 1985), pp. 291–293.
11. R.L. Keusseyan, J.L. Dilday, and B.S. Speck, Int. J. Microcircuits Electron. Packaging 17, 263 (1994).
12. S.W. Wilson, A.W. Norris, E.B. Scott, and M.R. Costello, Nat. Electron. Packaging Production Conf.-Proc. Techn. Program 2, 788 (1996).
13. J.C. Bolger, Proc. ACS Division of Polymeric Materials Science and Engineering (Washington, DC: ACS, Books & Journals Division, 1988), pp. 502–506.