journal article·2011-06

Tensile and Fatigue Behavior of Al-1Si Wire Used in Wire Bonding

F. D. Danaher, J. J. Williams, D. R. P. Singh, L. Jiang, N. Chawla

Journal of Electronic Materials· Volume 40· Issue 6
Publisher page

Abstract

In this work, the mechanical properties of Al-1Si microelectronic wire were studied. The microstructure of the wire was examined to characterize the distribution of Al-Si inclusions and grain size. The wires had a diameter of 63.3 ± 0.1 μm and an elongated grain structure due to the hot extrusion process used to fabricate them. The transverse grain size was measured to be 1.1 ± 0.3 μm. The anisotropy in grain structure was characterized by dual-beam focused ion beam (FIB). The Young’s modulus was measured by conducting experiments at various gage lengths. The measured modulus was 71.7 ± 6.1 GPa, similar to that of bulk Al-Si. Strength data were measured for many wires, and the variability evaluated by Weibull statistics. The wires had a strength slightly less than 200 MPa and strain to failure of over 2%. A Weibull modulus of 110 was obtained, indicating very low variability in the data. Stress versus fatigue cycles was also conducted. Specimens that survived 106 cycles exhibited a significant decrease in strength over the as-processed material. Fractographic analysis showed a significant amount of plastic flow and fracture by necking to a single point.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. D. Abdo, M. Mahalingam, F. Danaher, and A. Elliott, Proceedings of Motorola Technology Forum (2004).
2. K. Lang, G. Harman, and M. Schneider-Ramelow, Modern Wire Bonding Technologies—Ready for the Challenges of Future Microelectronics Packaging (Gaithersburg, MD: NIST, 2004).
3. H. Saiki, Y. Marumo, H. Nishitake, T. Uemura, and T. Yotsumoto, J. Mater. Process. Technol. 177, 709 (2006).10.1016/j.jmatprotec.2006.04.024 ↗
4. J. Bielen, J. Gomans, and F. Theunis, Prediction of High Cycle Fatigue in Aluminum Wires (Nijmegan, The Netherlands: Phillips Semiconductors, 2004), pp. 1–7.
5. J. Onuki, M. Koizumi, and M. Suwa, IEEE Trans. Adv. Packag. 23, 108 (2000).10.1109/6040.826768 ↗
6. R. Fitzsimmons and E. Henry Chia, IEEE Trans. Compon. Hybr. Manuf. Technol. 15, 1081 (1992).10.1109/33.206934 ↗
7. S. Ramminger, N. Seliger, and G. Wachutka, Microelectron. Reliab. 40, 1521 (2000).10.1016/S0026-2714(00)00139-6 ↗
8. Y. Liu and W. Kinzy Jones, J. Electron. Mater. 33, 929 (2004).10.1007/s11664-004-0018-9 ↗
9. G. Lefranc, B. Weiss, C. Klos, J. Dick, G. Khatibi, and H. Berg, Microelectron. Reliab. 43, 1833 (2003).10.1016/S0026-2714(03)00312-3 ↗
10. N. Chawla, M. Kerr, and K.K. Chawla, J. Am. Ceram. Soc. 88, 101 (2005).10.1111/j.1551-2916.2004.00007.x ↗
11. K.K. Chawla, Fibrous Materials (Cambridge: Cambridge University Press, 1998).10.1017/CBO9780511525209 ↗
12. G. Harman, Wire Bonding in Microelectronics Materials, Processes Reliability and Yield (New York, NY: McGraw Hill, 1997).
13. F. Silva, N. Chawla, and R.D. Toledo Filho, Compos. Sci. Technol. 68, 3448 (2008).10.1016/j.compscitech.2008.08.018 ↗
14. M. Kerr, N. Chawla, and K.K. Chawla, JOM 2, 67 (2005).10.1007/s11837-005-0219-6 ↗
15. J. Bielen, J. Gommans, and F. Theunis, Eurosime IEEE (2006), pp. 55–61.
16. A. Deyhim, B. Yost, M.-J. Lii, and C.-Y. Li, Electronic Components and Technology Conference (1996), pp. 836–841.