Microstructure and Reliability Comparison of Different Pb-Free Alloys Used for Wave Soldering and Rework
Source abstract
Abstract
This paper describes the results of an intensive microstructural and reliability study of pin-through-hole (PTH) and surface mount technology (SMT) components which were wave solder assembled using three groups of alloys: (1) near-eutectic Sn-Ag-Cu alloys such as SAC405 and SAC305, (2) low-Ag off-eutectic Pb-free alloys with an Ag content of about 1% and lower, and (3) eutectic Sn-Cu alloys with Ni and other additives. Both primary attach and reworked solder connections using solder fountain and hand rework were studied. The PTH connector types and SMT components were wave solder assembled on a test vehicle. Accelerated thermal cycling (ATC) was conducted at 0°C to 100°C for 6000 cycles. The difference in microstructures, intermetallic formation, Cu dissolution, grain coarsening, and crack formation is shown. The influence of the microstructure after assembly and rework on Weibull plot parameters and failure modes is described for 2512 resistors. Interconnect defects such as nonuniform phase distribution and void formation are discussed. The Sn-Cu-Ni- and Sn-Cu-Ag-Bi-based alloys tested in this study are recommended as potential suitable replacements for SAC305/405 in the wave solder process; no failure was detected up to 6000 cycles at 0°C to 100°C. Although SAC405 demonstrated better barrel fill and lower rate of crack propagation during ATC, after PTH rework, both of the alternative Pb-free alloys have a much lower Cu dissolution rate and definitely outperform SAC405 in ATC. SAC405 glue and wave resistors after primary attachment and rework demonstrate higher reliability than alternative alloys. Early failures relate to alternative alloy characteristics and should be considered for some applications.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Advanced Welding Techniques Analysis · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. C. Hamilton, P. Snugovsky, and M. Kelly, Proceedings of the Pan Pacific Microelectronics SMTA Conference (Mani, HI: SMT, 2007).
2. C. Hamilton and M. Kelly, Proceedings of IPC Printed Circuits Expo, APEX Conference (Los Vegas, NV: IPC, 2008).
3. C. Hamilton, P. Snugovsky, M. Moreno, T.H. Ng, J.␣Fangkangwanwong, M. Kelly, and J. Bielick, Proceedings of the Pan Pacific Microelectronics SMTA Conference (Kamuela, HI: SMTA, 2009).
4. C. Hamilton, P. Snugovsky, and M. Kelly, Proceedings of SMTA International Conference (Edina, MN: SMTA, 2006).
5. IPC, IPC-9701A Performance Test Methods and Qualification Requirements for Solder Mount Attachments (2006).
6. Y.N. Taran and V.I Mazur, Structure of Eutectic Alloys (Moscow: Metallurgy, 1978), p. 311.
7. L. Snugovsky, D.D. Perovic, and J.W. Rutter, J. Mater. Sci. 20, 1403 (2004).
8. L. Snugovsky, P. Snugovsky, D.D. Perovic, and J.W. Rutter, J. Mater. Sci. 21, 61 (2005).
9. N.J. Hoffman and I. Minkoff, Proceedings of American Society for Metals and the Metallurgical Society of AIME (1969), p. 391.
10. Y. Shoji, S. Uchida, and T. Ariga, Proceedings of American Society for Metals and the Metallurgical Society of AIME (1982), p. 441.
11. M. Kelly, M. Ferrill, P. Snugovsky, Z. Bagheri, R. Trivedi, G.␣Dinca, and C. Achong, Proceedings of IPC Printed Circuits Expo, APEX Conference (Los Vegas, NV: IPC, 2009).
12. P. Snugovsky, H. McCormic, S. Bagheri, Z. Bagheri, C. Hamilton, and M. Romansky, J. Electron. Mater. 38, 292 (2008).10.1007/s11664-008-0592-3 ↗