Low Temperature Consolidation of Micro/Nanosilver Die-Attach Preforms
Source abstract
Abstract
Organically passivated silver nanopowder paste-based sintering is considered a promising solution for die-attach in high temperature power and sensing electronic devices. However, oxygen requirements during burnout and inherently high shrinkage rates limit their use to small die sizes. This work reports an alternative fabrication method that resolves decomposition and shrinkage issues of the die-attach by utilizing a prestressed optimized tape cast mixture of micro- and nanosilver particles with a polypropylene carbonate binder. The effects of prestressing, micro/nanosilver bimodal distribution, and polymer content on resulting microstructure and shear strength were investigated. Prior to application as a die-attach, uniaxial compression of the tape was found to significantly decrease shrinkage and improve green strength. This pre-stressing strategy allows for a decoupling of the resulting die-attach materials properties from the pressure applied during assembly. Bimodal mixtures consisting of 1–3 μm spherical powders with nanosilver resulted in shear strengths comparable to those of pure nanosilver. Shear strength decreased as bimodal particle size increased above 5 μm. A polymer content of ∼10 wt.% polypropylene carbonate combined with prestressing was identified as optimal for maximizing die-attach shear strength while still maintaining pliability and formability. Tape casts that were prestressed to 212 MPa by uniaxially compression and formulated with 10 wt.% of polypropylene carbonate resulted in a die-attach material with a shear strength of 54 MPa when sintered. These materials were used to demonstrate void-free 25-mm2 die-attach assemblies, suggesting that tape cast micro/nanosilver materials may be a promising die-attach method for high temperature and large-area electronics devices.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Aluminum Alloys Composites Properties · 3D IC and TSV technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. H.S. Chin, K.Y. Cheong, and A.B. Ismail, Metall. Mater. Trans. B 41, 824 (2010).10.1007/s11663-010-9365-5 ↗
2. V.R. Manikam and K.Y. Cheong, IEEE Trans Compon. Packag. Manuf. Technol. 1, 457 (2011).10.1109/TCPMT.2010.2100432 ↗
3. K. Sheng, IEEE Trans. Electron. Devices 56, 337 (2009).10.1109/TED.2008.2010605 ↗
4. P. Neudeck and R. Okojie, Proc. IEEE 90, 1065 (2002).10.1109/JPROC.2002.1021571 ↗
5. J. Kähler, N. Heuck, A. Wagner, A. Stranz, E. Peiner, and A. Waag, IEEE Trans. Compon. Packag. Manuf. Technol. 2, 1587 (2012).10.1109/TCPMT.2012.2201940 ↗
6. H. Schwarzbauer and R. Kuhnert, IEEE Trans. Ind. Appl. 27, 93 (1991).10.1109/28.67536 ↗
7. T.G. Lei, J.N. Calata, G.Q. Lu, X. Chen, and S. Luo, IEEE Trans. Compon. Packag. Technol. 33, 98 (2010).10.1109/TCAPT.2009.2021256 ↗
8. M. Knoerr and A. Schletz, Power Electronics Systems (CIPS) (2010), pp. 16–18.
9. C. Gobl and J. Faltenbacher, Integrated Power Electronics (CIPS) (2010), pp. 16–18.
10. J. Kähler, N. Heuck, A. Stranz, A. Waag, and E. Peiner, IEEE Trans. Compon. Packag. Manuf. Technol. 2, 1 (2012).10.1109/TCPMT.2011.2181587 ↗
11. J. Kahler, N. Heuck, G. Palm, A. Stranz, A. Waag, and E. Peiner, 3rd Electronics System Integration Technology Conference ESTC (IEEE, 2010), pp. 1–5.10.1109/ESTC.2010.5642808 ↗
12. Z.Z. Zhang and G. Lu, IEEE Trans. Electron. Packag. Manuf. 25, 279 (2002).10.1109/TEPM.2002.807719 ↗
13. J. Bai, Z. Zhang, J. Calata, and G. Lu, Conference on High Density Microsystem Design and Packaging and Component Failure Analysis (IEEE, Shanghai, 2005), pp. 1–5.10.1109/HDP.2005.251412 ↗
14. J. Bai and G. Lu, IEEE Trans. Device Mater. Reliab. 6, 436 (2006).10.1109/TDMR.2006.882196 ↗
15. J. Bai, J. Calata, and G. Lu, IEEE Trans. Electron. Packag. Manuf. 30, 241 (2007).10.1109/TEPM.2007.906508 ↗
16. K. Suganuma, S. Sakamoto, N. Kagami, D. Wakuda, K.-S. Kim, and M. Nogi, Microelectron. Reliab. 52, 375 (2012).10.1016/j.microrel.2011.07.088 ↗
17. G. Zou, J. Yan, F. Mu, A. Wu, J. Ren, A. Hu, and N. Zhou, Open Surf. Sci. J. 3, 70 (2011).10.2174/1876531901103010070 ↗
18. H. Nishikawa, T. Hirano, T. Takemoto, and N. Terada, Open Surf. Sci. J. 3, 60 (2011).10.2174/1876531901103010060 ↗
19. R. Eisele, J. Rudzki, and M. Kock, PCIM Europe (2007).
20. R.M. German, Powder Metallurgy Science, 2nd ed. (1994).
21. G. Bai, Low-Temperature Sintering of Nanoscale Silver Paste for Semiconductor Device Interconnection (Blacksburg: Virginia Polytechnic Institute and State University, 2005).
22. J.W. Gilman, D.L. VanderHart, and T. Kashiwagi, Fire and Polymers II: Materials and Test for Hazard Prevention ACS (Washington, DC: ACS, 1994), pp. 161–185.
23. L.C.K. Liau and D.S. Viswanath, Ind. Eng. Chem. Res. 37, 49 (1998).10.1021/ie970434b ↗
24. E.R. Mistler and R.E. Twiname, Tape Casting Theory and Practice (Westerville: Wiley–American Ceramic Society, 2000).
25. H. Yan, W.R. Cannon, and D.J. Shanefield, Ceram. Int. 24, 433 (1998).10.1016/S0272-8842(97)00032-1 ↗
26. K. Sato, H. Yılmaz, A. Ijuin, Y. Hotta, and K. Watari, Appl. Surf. Sci. 258, 4011 (2012).10.1016/j.apsusc.2011.12.091 ↗
27. C. Martin, D. Bouvard, and S. Shima, J. Mech. Phys. Solids 51, 667 (2003).10.1016/S0022-5096(02)00101-1 ↗
28. J.G. Bai, T.G. Lei, J.N. Calata, and G.-Q. Lu, J. Mater. Res. 22, 3494 (2007).10.1557/JMR.2007.0440 ↗
29. D. Hudson, J. Appl. Phys. 20, 154 (1949).10.1063/1.1698327 ↗
30. R.M. German, Acta Metall. Mater. 40, 2085 (1992).10.1016/0956-7151(92)90125-X ↗
31. W. Visscher, Nature 239, 504 (1972).10.1038/239504a0 ↗
32. R. German, Metall. Trans. A 23A, 1455 (1992).10.1007/BF02647329 ↗
33. M. Mirjalili and J. Vahdatikhaki, J. Phys. Chem. Solids 69, 2116 (2008).10.1016/j.jpcs.2008.03.014 ↗
34. G.-Q. Lu, M. Zhao, G. Lei, J.N. Calata, X. Chen, and S. Luo, International Conference on Electronic Packaging Technology & High Density Packaging (IEEE, 2009), pp. 461–466.