Current-carrying capacity of anisotropic-conductive film joints for the flip chip on flex applications
Source abstract
Abstract
The effect of the substrate-pad physical properties (surface roughness and hardness) on the current-carrying capacity of anisotropic-conductive film (ACF) joints is investigated in this work. Flip chips with Au bumps were bonded to the flexible substrates with Au/Cu and Au/Ni/Cu pads using different bonding pressure. It was found that the current-carrying capacity of ACF joints increased to a maximum value with the rise of the bonding pressure; then, it reduced if the bonding pressure continually increased. The maximum average value per unit area of Au/Ni/Cu pad and Au/Cu pad ACF joints is about 93 µA/µm2 and 118 µA/µm2, respectively, at 100-MPa bonding pressure. The variation trend of connection resistance is the opposite of current-carrying capacity. The variation of current-carrying capacity (or connection resistance) of Au/Cu pad joints is larger than that of Au/Ni/Cu pad joints. The current-carrying capacity is related to the variation of the resistance of ACF joints. The connection resistance of ACF joints depends primarily on the particle constriction resistance (Rcoi), Rcoi ∞ 1/a, where “a” is the radius of contact spot. A smaller contact area results in larger joule heat generation per unit volume (Qg), Qg ∞ 1/a4, which preferentially elevates the temperature of the constriction. The raised temperature increases the resistance because of the temperature-dependent coefficient of the metal resistivity. The theory of tribology is used to explain the difference between Au/Cu pad and Au/Ni/Cu pad ACF joints. For the Au/Cu pad ACF joints, the deformation of the particles’ upper and bottom sides is nearly symmetrical; the contact between conductive particles and pad has the character of “sliding contact,” especially under high pressure. For the Au/Ni/Cu pad ACF joint, the contact between particles and pad determined the conduction characteristics of ACF joints. It has the character of “static contact.” Thus, the current-carrying capacity (or connection resistance) of Au/Cu pad joints is more sensitive to the bonding pressure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Adhesion, Friction, and Surface Interactions · 3D IC and TSV technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. J. Liu, ed., Conductive Adhesives for Electronics Packaging (British Isles: Electrochemical Publications Ltd, 1999), pp. 317–320.
2. A.O. Ogunjimi, O. Boyle, D.C. Whalley, and D.J. Williams, J. Electron. Manuf. 2, 109 (1992).10.1142/S0960313192000145 ↗
3. R. Aschenbrenner, R. MieBner, and H. Reichl, J. Electron. Manuf. 7, 245 (1997).10.1142/S0960313197000257 ↗
4. U. Behner, R. Haug, R. Schutz, and H.L. Hartnagel, IEEE Trans. Comp., Packag., Manuf. Technol. Part A 21, 243 (1998).10.1109/95.705470 ↗
5. N. Shiozawa, K. Isaka, and T. Ohta, J. Electron. Manuf. 5, 33 (1995).10.1142/S0960313195000062 ↗
6. K. Kulojarvi, P. Savolainen, and J. Kivilahti, Proc. 10th European Micro. Conf. (Copenhagen, Denmark, 1995), pp. 28–34.
7. Y. Wei and E. Sancaktar, Proc. ISHM’95 (1995), pp. 231–236.
8. R. Holm, Electric Contacts, 4th ed. (New York: Springer-Verlag, 1981).
9. F.L. Jones, The Physics of Electrical Contacts (Oxford, United Kingdom: Clarendon Press, 1957).
10. F.G. Shi, M. Abdullah, S. Chungpaiboonpatana, K. Okuyama, C. Davidson, and J.M. Adams, Mater. Sci. Semicond. Process. 2, 263 (1999).10.1016/S1369-8001(99)00018-9 ↗
11. S.H. Fan and Y.C. Chan, accepted for publication in Microelectr. Reliab.
12. C.N. Oguibe, S.H. Mannan, D.C. Whalley, and D.J. Williams, 1st IEEE Int. Symp. on Polymeric Electronics Packaging Proc. (Norrkoping, Sweden, 1997), pp. 249–258.
13. C. Kittel, Introduction to Solid State Physics (New York: John Wiley & Sons, 1976).
14. M.-J. Yim and K.-W. Paik, IEEE Trans. Adv. Packag. 22, 166 (1999).10.1109/6040.763188 ↗
15. B. Bharat, Handbook of Micro/Nano Tribology, 2nd ed. (Boca Raton, FL: CRC Press, 1999), pp. 187–192.
16. T.R. Thomas, Rough Surface, 2nd ed., (London: Imperial College Press, 1999), ch. 10.
17. Y.S. Zhai, A. Li, and J.Z. Zhang, Applied Tribology (Dongying, China: Press of Petroleum University, 1996).
18. Technical information on http://www.webelements.com, enter the bulk properties under corresponding elements item.