Effects of prestrain, rate of prestrain, and temperature on the stress-relaxation behavior of eutectic Sn-3.5Ag solder joints
Source abstract
Abstract
Stress-relaxation studies on eutectic Sn-Ag solder (Sn-3.5Ag in wt.%) joints were carried out at various temperatures after imposing different amounts and rates of simple shear strain. Stress-relaxation parameters were evaluated by subjecting geometrically realistic solder joints with a nominal joint thickness of ∼100 µm and a 1 mm × 1 mm solder-joint area. The peak shear stress during preloading and residual shear stress resulting from stress relaxation were higher at the low-temperature extremes than those at high-temperature extremes. Also, those values increased with increasing simple shear strain and the rate of simple shear strain imposed prior to the stress-relaxation events. The relaxation stress is insensitive to simple shear strain at 150°C, but at lower temperatures, a faster rate of simple shear strain causes a higher relaxed-stress value. The resulting deformation structures observed from the solder-joint side surfaces were also strongly affected by these parameters. At high temperature, grain-boundary sliding effects were commonly observed. At low temperature, intense shear bands dominated, and no grain-boundary sliding effects were observed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. J.G. Lee and K.N. Subramanian, J. Electron. Mater. 32, 523 (2003).10.1007/s11664-003-0137-8 ↗
2. J.G. Lee, F. Guo, S. Choi, K.N. Subramanian, T.R. Bieler, and J.P. Lucas, J. Electron. Mater. 31, 946 (2002).10.1007/s11664-002-0188-2 ↗
3. S. Choi, J.G. Lee, K.N. Subramanian, J.P. Lucas, and T.R. Bieler, J. Electron. Mater. 31, 292 (2002).10.1007/s11664-002-0146-z ↗
4. S.G. Jadhav, T.R. Bieler, K.N. Subramanian, and J.P. Lucas, J. Electron. Mater. 30, 1197 (2001).10.1007/s11664-001-0150-8 ↗
5. H. Mavoori, J. Chin, S. Vaynman, B. Moran, L. Keer, and M. Fine, J. Electron. Mater. 26, 783 (1997).10.1007/s11664-997-0252-z ↗
6. E.W. Hare and R.G. Stang, J. Electron. Mater. 24, 1473 (1995).10.1007/BF02655466 ↗
7. D. Tribula, D. Grivas, and J.W. Morris, J. Electron. Mater. 17, 387 (1988).10.1007/BF02652123 ↗
8. R. Arrowood and A.K. Mukherjee, Mater. Sci. Eng. 92, 33 (1987).10.1016/0025-5416(87)90154-6 ↗
9. R.W. Rohde and J.C. Swearengen, J. Eng. Mater. Technol. 102, 207 (1980).10.1115/1.3224799 ↗
10. E. Baker, Mater. Sci. Eng. 38, 241 (1979).10.1016/0025-5416(79)90128-9 ↗
11. H. Rhee, K.N. Subramanian, A. Lee, and J.G. Lee, Solder. Surf. Mount Technol., in press.
12. A.U. Telang (M.S. thesis, Michigan State University, 2002).
13. F. Hua and J. Glazer, Design and Reliability of Solders and Solder Interconnections, ed., R.K. Mahidhara (Warrendale, PA: TMS, 1997), p. 66–74.
14. W.L. Winterbottom, JOM 45, 20 (1993).10.1007/BF03222375 ↗
15. J.H. Lau, ed., Thermal Stress and Strain in Microelectronics Packaging (New York: Van Nostrand Reinhold, 1993), pp. 472–479.