journal article·2015-11

Optimization of the Mechanical and Electrical Performance of a Thermoelectric Module

Ali Sarhadi, Rasmus Bjørk, Nini Pryds

Journal of Electronic Materials· Volume 44· Issue 11
Publisher page

Abstract

Finite-element simulation of a thermoelectric (TE) module was conducted to optimize its geometrical dimensions in terms of mechanical reliability and performance. The TE module consisted of bismuth telluride n- and p-type legs. The geometrical dimensions of the module, i.e., leg length and leg cross-sectional area, were varied, and the corresponding maximum thermal stress, output power, and efficiency of the module obtained. An optimal design for the module was then suggested based on minimizing the thermal stresses and maximizing the performance, i.e., power and efficiency. The optimal dimensions at maximum von Mises stress of 75 MPa were leg length of 2 mm to 2.5 mm and leg width of 1.5 mm to 2 mm, resulting in efficiency of 7.2%. Finally, the influence of solders, i.e., solder material between the leg, the interconnector, and the top ceramic layer, on the induced thermal stresses and module performance was investigated. The results revealed that the transition from elastic to plastic deformation in the solder decreased the induced thermal stresses significantly. Moreover, beyond the elastic limit, the stress magnitude was highly dependent on the magnitude and mechanism of plastic deformation in the module. The present study provides a basis for a unique and new optimization scheme for TE modules in terms of endurance and performance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal properties of materials · Thermal Radiation and Cooling Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. P.H. Ngan, D.V. Christensen, G.J. Snyder, L.T. Hung, S. Linderoth, N. Van Nong, and N. Pryds, Phys. Status Solidi 211, 9 (2014).10.1002/pssa.201330155 ↗
2. E. Suhir and A. Shakouri, J. Appl. Mech. 80, 021012 (2012).10.1115/1.4007524 ↗
3. E. Suhir and A. Shakouri, J. Appl. Mech. 79, 061010 (2012).10.1115/1.4006597 ↗
4. A. Ziabari, E. Suhir, and A. Shakouri, Microelectron. J. 45, 547 (2014).10.1016/j.mejo.2013.12.004 ↗
5. T. Clin, S. Turenne, D. Vasilevskiy, and R.A. Masut, J. Electron. Mater. 38, 994 (2009).10.1007/s11664-009-0756-9 ↗
6. J.-L. Gao, Q.-G. Du, X.-D. Zhang, and X.-Q. Jiang, J. Electron. Mater. 40, 884 (2011).10.1007/s11664-011-1611-3 ↗
7. M. Picard, S. Turenne, D. Vasilevskiy, and R.A. Masut, J. Electron. Mater. 42, 2343 (2013).10.1007/s11664-012-2435-5 ↗
8. J.C. Simo and T.J.R. Hughes, Computational Inelasticity (New York: Springer, 1998), pp. 71–151.
9. M.-H. Yu, G.-W. Ma, H.-F. Qiang, and Y.-Q. Zhang, Generalized Plasticity (Berlin: Springer, 2006), pp. 122–153
10. J. Chakrabarty, Applied Plasticity, ed. F.F. Ling, 2nd edn. (Boston, MA: Springer, 2010), pp. 1–48.
11. R. Bjørk, D.V. Christensen, D. Eriksen, and N. Pryds, Int. J. Therm. Sci. 85, 12 (2014).10.1016/j.ijthermalsci.2014.06.003 ↗
12. H.L. Ni, X.B. Zhao, T.J. Zhu, X.H. Ji, and J.P. Tu, J. Alloys Compd. 397, 317 (2005).10.1016/j.jallcom.2005.01.046 ↗
13. Y. Ma, Q. Hao, B. Poudel, Y. Lan, B. Yu, D. Wang, G. Chen, and Z. Ren, Nano Lett. 8, 2580 (2008).10.1021/nl8009928 ↗
14. W.J. Xie, J. He, S. Zhu, X.L. Su, S.Y. Wang, T. Holgate, J.W. Graff, V. Ponnambalam, S.J. Poon, X.F. Tang, Q.J. Zhang, and T.M. Tritt, Acta Mater. 58, 4705 (2010).10.1016/j.actamat.2010.05.005 ↗
15. ASM International Handbook Committee, Metals Handbook, Vol.2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, 10th edn. (ASM International, Materials Park, 1990).