journal article·2001-09

Shear deformation in Sn-3.5Ag and Sn-3.6Ag-1.0Cu solder joints subjected to asymmetric four-point bend tests

B. A. Cook, I. E. Anderson, J. L. Harringa, R. L. Terpstra, J. C. Foley, Ö. Ünal, F. C. Laabs

Journal of Electronic Materials· Volume 30· Issue 9
Publisher page

Abstract

The shear deformation behavior of two lead-free solder compositions, Sn-3.5Ag (wt.%) and Sn-3.6Ag-1.0Cu (wt.%), both on copper substrates, was studied using an asymmetric four point bend technique. Four test joints were obtained from one master specimen of each composition, and each joint was subject to progressive loading, up to the maximum shear strength of the joint. One unstressed bar from each composition was retained as a reference. Each sample was metallo-graphically plished and lightly etched, and examined in a field emission scanning electron microscope (SEM) before shearing. Sheared joints were then re-examined in the SEM with no additional surface treatment. Compared with the traditional ring and plug method, the asymmetric four-point bend (AFPB) technique subjects the joints to a condition of pure shear, while providing an opportunity for unambiguous observation of microstructural features before and after shearing, without an intervening mechanical sectioning step. Shear banding in the Sn-rich matrix and crack nucleation in the vicinity of the intermetallic interface were observed at low displacements in the binary alloy. Evidence of non-homogeneous plastic flow in the matrix was seen at higher shear loading. No evidence of brittle fracture was observed in the Sn-3.6Ag-1.0 Cu alloy, with elastic deformation at low stress levels giving rise to plastic deformation at higher loading values. Results show that the AFPB technique is a viable approach to the study of shear loading on solder joints.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. J. Bath, C. Handweker, and E. Bradley, Circuits Assembly (2000), p. 31.
2. C.M. Miller, I.E. Anderson, and J.F. Smith, J. Electron. Mater. 23, 595 (1994).10.1007/BF02653344 ↗
3. I.E. Anderson, T.E. Bloomer, R.L. Terpstra, J.C. Foley, B.A. Cook, and J.L. Harringa, Proc. Int. Brazing and Soldering Conf. 2000 (Miami, FL: Amer. Welding Soc., 2000), p. 575.
4. I.E. Anderson, NEPCON West (Norwalk, CT: Reed Exhibition Co., 1996), p. 882.
5. S. Jin, JOM 45, 13 (1993).10.1007/BF03222373 ↗
6. D.R. Frear, IEEE Trans. on Compon., Hybrids, and Mfg. Technol. 12, 492 (1989).10.1109/33.49006 ↗
7. D.R. Freer and P.T. Vianco, Met. Trans. A 25A, 1509 (1994).10.1007/BF02665483 ↗
8. J.C. Foley, A. Gickler, F.H. Leprevost, and D. Brown, J. Electron. Mater. 29, 1258 (2000).10.1007/s11664-000-0021-8 ↗
9. Ö. Ünal, I.E. Anderson, and S. Maghsoodi, J. Amer. Ceram. Soc. 80, 1281 (1997).10.1111/j.1151-2916.1997.tb02977.x ↗
10. Ö. Ünal, D.J. Barnard, and I.E. Anderson, Scripta Mat. 40, 271 (1999).10.1016/S1359-6462(98)00432-1 ↗
11. T. Bloomer (Master’s thesis, Iowa State University, 1999).
12. Int. Tin Res. Inst. Mech. Prop. Standards (Middlesex, U.K.: Int. Tin Res. Inst., 1992).
13. I.E. Anderson, T.E. Bloomer, J.C. Foley, and R.L. Terpstra, Proc. of IPC Works’99, Northbrook, IL: IPC, 1999), Paper No. S-03-5.
14. ANSYS 5.5, University version (ANSYS, Inc., Canonsburg, PA 15317).
15. T.C. Hufnagel, P. El-Deiry, and R.P. Vinci, Scripta Mat. 43, 1071 (2000).10.1016/S1359-6462(00)00527-3 ↗
16. J.L. Roberts, Effect of Lead Contamination on Some Leadfree Solder Alloys, Report 0401RE96 (Ann Arbor, MI: National Center for Mfg. Sci., 1997).
17. M.A. Meyers and K.K. Chawla, Mechanical Metallurg: Principles and Applications (Upper Saddle River, NJ: Prentice-Hall, Inc., 1984), p. 147.
18. C.A. Pampillo, J. Mater. Sci. 10, 1194 (1975).10.1007/BF00541403 ↗
19. D. Freer, Fracture Behavior of Pb-Free Solder Alloys, Report 0401RE96 (Ann Arbor, MI: National Center for Mfg. Sci., 1997).