Effects of Bi and Pb on oxidation in humidity for low-temperature lead-free solder systems
Source abstract
Abstract
The oxidation behavior of various Sn-Zn(-Bi) alloys during 60°C/90% and 85°C/85% relative humidity (RH) exposure were investigated by microstructure observation and x-ray diffraction analysis. The mechanical property of the joints of resistor chips (1608R) with two kinds of terminations, Sn and Sn-10Pb, soldered on a printed circuit board with Sn-Zn(-Bi) were evaluated by a shear test. The heat/humidity exposure of Sn-Zn alloys promotes segregation into the grain boundary accompanying oxidation of Zn resulting in the ZnO formation. This segregation induces serious degradation of alloys and Sn whisker growth. Heat/humidity exposure of 85°C/85%RH seriously decreases the shear strength of the surface mounted chip joints, especially Sn-Zn-Bi solder, due to the formation of ZnO at the interface between the solder and the reaction layer. The presence of Bi or Pb in Sn-Zn alloys enhances the diffusion, resulting in severe degradation at 85°C/85%RH exposure. In contrast, the exposure at 60°C/90%RH does not influence the joint strength for up to 1000 h. Under this condition, the oxidation of Zn only reaches a few microns in depth from the free surface.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. M. McCormack and S. Jin, JOM 45, 36 (1993).10.1007/BF03222379 ↗
2. C. Melton, JOM 45, 33 (1993).10.1007/BF03222378 ↗
3. K. Suganuma, Y. Nakamura, and K. Nihara, J. Mater. Res. 13, 2859 (1998).10.1557/JMR.1998.0391 ↗
4. E.P. Wood and K.L. Nimmo, J. Electron. Mater. 23, 709 (1994).10.1007/BF02651363 ↗
5. M.E. Loomans, S. Vaynman, G. Gosh, and M.E. Fine, J. Electron. Mater. 23, 741 (1994).10.1007/BF02651368 ↗
6. K. Suganuma, T. Murata, H. Noguchi, and Y. Toyoda, J. Mater. Res. 15, 884 (2000).10.1557/JMR.2000.0126 ↗
7. K.-S. Kim, Y.-S. Kim, K. Suganuma, and H. Nakajima, J. Jpn. Inst. Electron. Packaging 5, 666 (2002).10.5104/jiep.5.666 ↗
8. S.W. Yoon, W.K. Choi, and H.M. Lee, Scripta Mater. 40, 327 (1999).10.1016/S1359-6462(98)00414-X ↗
9. T. Kiga, S. Hattori, and Y. Iwanabe, J. Jpn. Inst. Electron. Packaging 6, 420 (2003).10.5104/jiep.6.420 ↗
10. M. Kitajima, T. Shono, T. Ogino, T. Kobayashi, K. Yamazaki, and M. Noguchi, J. Jpn. Inst. Electron. Packaging 6, 433 (2003).10.5104/jiep.6.433 ↗
11. K. Young-Sun, C.W. Hwang, and K. Suganuma, Proc. Int. Conf. on Electronics Packaging (2001 ICEP) (Tokyo, Japan: Japan Institute of Electronics Packaging/IMAPS, 2001), pp. 84–87.
12. M. Abtew and G. Selvaduray, Mater. Sci. Eng. 27, 95 (2000).10.1016/S0927-796X(00)00010-3 ↗
13. U. Lindborg, Acta Metall. 24, 181 (1976).10.1016/0001-6160(76)90021-3 ↗
14. K.N. Tu, Phys. Rev. B: Condens. Matter Mater. Phys. 49, 2030 (1994).10.1103/PhysRevB.49.2030 ↗
15. K.N. Tu, Mater. Chem. Phys. 46, 217 (1996).10.1016/S0254-0584(97)80016-8 ↗
16. B.Z. Lee and D.N. Lee, Acta Mater. 46, 3701 (1998).10.1016/S1359-6454(98)00045-7 ↗
17. K.W. Moon, M.E. Williams, C.E. Johnson, and G.R. Stafford, C.A. Handwerker, and W.J. Boettinger, Proc. 4th Pacific Rim Int. Conf. on Advanced Materials and Processing (Sendai, Japan: Japan Institute of Metals, 2001), pp. 1115–1118.
18. R. Schety, Circ. World 27-2, 17 (2001).10.1108/03056120110367131 ↗
19. T. Nagai, K. Natori, and T. Furusawa, J. Jpn. Inst. Met. 53, 303 (1989).10.2320/jinstmet1952.53.3_303 ↗