Improving the Seebeck Coefficient and Electrical Conductivity of Fe11Ti3Al6 by Substituting Fe with Cr
Source abstract
Abstract
Abstract In general, any attempt to increase the Seebeck coefficient is usually accompanied by a decrease in the electrical conductivity or vice versa due to the interplay between these two parameters. This work demonstrates that a simultaneous increase in both the Seebeck coefficient and electrical conductivity can be obtained by “doping” in intermetallic alloys. A new alloy composition, Fe10Cr1Ti3Al6, was synthesized by substituting Fe with Cr in Fe11Ti3Al6 using mechanical alloying and spark plasma sintering (SPS). The thermoelectric measurements revealed that the Cr substitution led to an increase in the Seebeck coefficient from +27 µV/K in Fe11Ti3Al6 to +39 µV/K in Fe10Cr1Ti3Al6, with a corresponding increase in the electrical conductivity from 2.5 × 105 S/m to 4.7 × 105 S/m, resulting in a significant increase in the power factor. The temperature dependence of the thermoelectric properties of this new alloy was also investigated over a temperature range of 50–727°C. The result showed that a maximum power factor of 6.0 × 10−4 W/m K2 was obtained at 53°C.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal properties of materials · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. A. Zoungrana and M. Çakmakci, From non-renewable energy to renewable by harvesting salinity gradient power by reverse electrodialysis: a review. Int. J. Energy Res. 45, 3495 (2021). https://doi.org/10.1002/er.6062.10.1002/er.6062 ↗
2. Ritchie, H. Fossil Fuels. https://ourworldindata.org/energy (2020).
3. R.B. Jackson, C. Le Quéré, R.M. Andrew, J.G. Canadell, G.P. Peters, J. Roy, and L. Wu, Warning signs for stabilizing global CO2 emissions. Environ. Res. Lett. (2017). https://doi.org/10.1088/1748-9326/aa9662.10.1088/1748-9326/aa9662 ↗
4. A. Midilli, I. Dincer, and M.A. Rosen, The role and future benefits of green energy. Int. J. Green Energy 4, 65 (2007). https://doi.org/10.1080/15435070601015494.10.1080/15435070601015494 ↗
5. Q. Zhang, Y. Sun, W. Xu, and D. Zhu, Organic thermoelectric materials: emerging green energy materials converting heat to electricity directly and efficiently. Adv. Mater. 26, 6829 (2014). https://doi.org/10.1002/adma.201305371.10.1002/adma.201305371 ↗
6. C. Gayner and K.K. Kar, Recent advances in thermoelectric materials. Progr. Mater. Sci. 83, 330 (2016). https://doi.org/10.1016/j.pmatsci.2016.07.002.10.1016/j.pmatsci.2016.07.002 ↗
7. M. Rull-Bravo, A. Moure, J.F. Fernández, and M. Martín-González, Skutterudites as thermoelectric materials: revisited. RSC Adv. 5, 41653 (2015). https://doi.org/10.1039/c5ra03942h.10.1039/c5ra03942h ↗
8. M. Christensen, S. Johnsen, and B.B. Iversen, Thermoelectric clathrates of type i. Dalton Trans. 39, 978 (2010). https://doi.org/10.1039/b916400f.10.1039/b916400f ↗
9. G.J. Snyder, and E.S. Toberer, Complex thermoelectric materials. Nat. Mater. 7, 105 (2008). https://doi.org/10.1038/nmat2090.10.1038/nmat2090 ↗
10. L. Huang, Q. Zhang, B. Yuan, X. Lai, X. Yan, and Z. Ren, Recent progress in half-Heusler thermoelectric materials. Mater. Res. Bull. 76, 107 (2016). https://doi.org/10.1016/j.materresbull.2015.11.032.10.1016/j.materresbull.2015.11.032 ↗
11. T.R. Wei et al., Copper chalcogenide thermoelectric materials. Sci. China Mater. 62, 8 (2019). https://doi.org/10.1007/s40843-018-9314-5.10.1007/s40843-018-9314-5 ↗
12. G. Ren et al., High performance oxides-based thermoelectric materials. JOM 67, 211 (2015). https://doi.org/10.1007/s11837-014-1218-2.10.1007/s11837-014-1218-2 ↗
13. T.R. Wei, C.F. Wu, F. Li, and J.F. Li, Low-cost and environmentally benign selenides as promising thermoelectric materials. J. Mater. 4, 304 (2018). https://doi.org/10.1016/j.jmat.2018.07.001.10.1016/j.jmat.2018.07.001 ↗
14. Y. Takagiwa, Y. Isoda, M. Goto, and Y. Shinohara, Conduction type control and power factor enhancement of the thermoelectric material Al2Fe3Si3. J. Phys. Chem. Solids 118, 95 (2018). https://doi.org/10.1016/j.jpcs.2018.03.003.10.1016/j.jpcs.2018.03.003 ↗
15. S. Anand et al., Thermoelectric transport of semiconductor full-Heusler VFe2Al. J. Mater. Chem. C 8, 10174 (2020). https://doi.org/10.1039/d0tc02659j.10.1039/d0tc02659j ↗
16. Y. Nishino, Thermoelectric Energy Conversion 143–156 (Elsevier, 2021).
17. P. Qiu, X. Shi, and L. Chen, Cu-based thermoelectric materials. Energy Storage Mater. 3, 85 (2016). https://doi.org/10.1016/j.ensm.2016.01.009.10.1016/j.ensm.2016.01.009 ↗
18. H. Okamura, J. Kawahara, T. Nanba, S. Kimura, K. Soda, U. Mizutani, Y. Nishino, M. Kato, I. Shimoyama, H. Miura, K. Fukui, K. Nakagawa, H. Nakagawa, and T. Kinoshita, Pseudogap formation in the intermetallic compounds (Fe1−xVx)3Al. Phys. Rev. Lett. 84(16), 3674 (2000). https://doi.org/10.1103/PhysRevLett.84.3674.10.1103/PhysRevLett.84.3674 ↗
19. H. Miyazaki, S. Tanaka, N. Ide, K. Soda, and Y. Nishino, Thermoelectric properties of Heusler-type off-stoichiometric Fe2V1+xAl1-x alloys. Mater. Res. Exp. (2014). https://doi.org/10.1088/2053-1591/1/1/015901.10.1088/2053-1591/1/1/015901 ↗
20. J. García-Cañadas, N.J. Adkins, S. McCain, B. Hauptstein, A. Brew, D.J. Jarvis, and G. Min, Accelerated discovery of thermoelectric materials: combinatorial facility and high-throughput measurement of thermoelectric power factor. ACS Combin. Sci. 18, 314 (2016). https://doi.org/10.1021/acscombsci.5b00178.10.1021/acscombsci.5b00178 ↗
21. T. Zou et al., Band structure modification of the thermoelectric Heusler-phase TiFe2Sn via Mn substitution. Phys. Chem. Chem. Phys. 19, 18273 (2017). https://doi.org/10.1039/c7cp02744c.10.1039/c7cp02744c ↗
22. K. Fukuta, K. Tsuchiya, H. Miyazaki, and Y. Nishino, Improving thermoelectric performance of Fe2VAl-based Heusler compounds via high-pressure torsion. Appl. Phys. A 128, 1 (2022).10.1007/s00339-022-05329-y ↗
23. A. Srinithi, H. Sepehri-Amin, Y. Takagiwa, and K. Hono, Effect of microstructure on the electrical conductivity of p-type Fe–Al–Si thermoelectric materials. J. Alloy. Compd. 903, 163835 (2022).10.1016/j.jallcom.2022.163835 ↗
24. Riss, P. D.-I. A., Garmroudi, P. D.-I. F., Parzer, P. D.-I. M. & Reumann, N. Physical properties of Fe2-xCrxVAl-type full Heusler compounds. (2021).
25. A. Kundu, A. Sittiho, I. Charit, B. Jaques, and C. Jiang, Development of Fe-9Cr alloy via high-energy ball milling and spark plasma sintering. JOM 71, 2846 (2019). https://doi.org/10.1007/s11837-019-03530-8.10.1007/s11837-019-03530-8 ↗
26. J. García-Cañadas and G. Min, Multifunctional probes for high-throughput measurement of Seebeck coefficient and electrical conductivity at room temperature. Rev. Sci. Instrum. (2014). https://doi.org/10.1063/1.4871553.10.1063/1.4871553 ↗
27. M. Rafiei, M. Enayati, and F. Karimzadeh, Characterization and formation mechanism of nanocrystalline (Fe, Ti)3Al intermetallic compound prepared by mechanical alloying. J. Alloy. Compd. 480, 392 (2009).10.1016/j.jallcom.2009.02.072 ↗
28. S.-M. Zhu and K. Iwasaki, Characterization of mechanically alloyed ternary Fe–Ti–Al powders. Mater. Sci. Eng. A 270, 170 (1999).10.1016/S0921-5093(99)00146-X ↗
29. R. Hasan and S.C. Ur, Thermoelectric and transport properties of FeV1−xTixSb Half-Heusler system synthesized by controlled mechanical alloying process. Electron. Mater. Lett. 14, 725 (2018). https://doi.org/10.1007/s13391-018-0088-0.10.1007/s13391-018-0088-0 ↗
30. M.H. Enayati and M. Salehi, Formation mechanism of Fe3Al and FeAl intermetallic compounds during mechanical alloying. J. Mater. Sci. 40, 3933 (2005). https://doi.org/10.1007/s10853-005-0718-4.10.1007/s10853-005-0718-4 ↗
31. E.P. Elsukov, E.V. Voronina, A.S. Shuravin, A.V. Zagainov, A.V. Korolev, S.K. Godovikov, E.A. Pechina, and A.E. Elsukova, Structure of the Fe100-xAlx alloys (25<x<35 at.%) annealed in a temperature range of 400–800°C and the effect of the ordering type on the magnetic properties. Phys. Met. Metallograph. 102, 55 (2006).10.1134/S0031918X06070076 ↗
32. A. Mulyawan, T. Terai, and T. Fukuda, Interpretation of Fe-rich part of Fe–Al phase diagram from magnetic properties of A2-, B2-, and DO3-phases. J. Alloy. Compd. 834, 155140 (2020).10.1016/j.jallcom.2020.155140 ↗
33. D. Panda, L. Kumar, and S.N. Alam, Development of Al-Fe3Al nanocomposite by powder metallurgy route. Mater. Today Proc. 2, 3565 (2015).10.1016/j.matpr.2015.07.070 ↗
34. O.I. Tolochyn, O.V. Tolochyna, H.A. Bagliuk, Y.I. Yevych, Yu.M. Podrezov, and A.A. Mamonova, Influence of sintering temperature on the structure and properties of powder iron aluminide Fe3Al. Powder Metall. Met. Ceram. 59, 150 (2020).10.1007/s11106-020-00150-9 ↗
35. L. Huang, R. He, S. Chen, H. Zhang, K. Dahal, H. Zhou, H. Wang, Q. Zhang, and Z. Ren, A new n-type half-Heusler thermoelectric material NbCoSb. Mater. Res. Bull. 70, 773 (2015).10.1016/j.materresbull.2015.06.022 ↗
36. X. Chen, A. Weathers, A. Moore, J. Zhou, and L. Shi, Thermoelectric properties of cold-pressed higher manganese silicides for waste heat recovery. J. Electron. Mater. 41, 1564 (2012). https://doi.org/10.1007/s11664-012-1987-8.10.1007/s11664-012-1987-8 ↗
37. N. Reumann, A. Riss, F. Garmroudi, M. Parzer, J. Kovacevic, T. Mori, and E. Bauer, Thermoelectric properties and low-temperature transport anomalies in the p-type full-Heusler compounds Fe2−xCrxVAl. Phys. Rev. B 106(23), 235138 (2022).10.1103/PhysRevB.106.235138 ↗
38. B. Hinterleitner, P. Fuchs, J. Rehak, F. Garmroudi, M. Parzer, M. Waas, R. Svagera, S. Steiner, M. Kishimoto, R. Moser, R. Podloucky, and E. Bauer, Stoichiometric and off-stoichiometric full Heusler Fe2V1−xWxAl thermoelectric systems. Phys. Rev. B (2020). https://doi.org/10.1103/PhysRevB.102.075117.10.1103/PhysRevB.102.075117 ↗
39. H. Matsuura, Doping effects on thermoelectric properties of the pseudogap Fe2VAl system. J. Jpn. Inst. Metals 66, 767 (2002).10.2320/jinstmet1952.66.7_767 ↗
40. T. Saito, S. Kamishima, and D. Nishio-Hamane, Thermoelectric and magnetic properties of (Fe, Co)2TiSn Heusler compounds. Phys. B Condens. Matter 639, 413984 (2022).10.1016/j.physb.2022.413984 ↗
41. A. Novitskii, I. Serhiienko, A. Nepapushev, A. Ivanova, T. Sviridova, D. Moskovskikh, A. Voronin, H. Miki, and V. Khovaylo, Mechanochemical synthesis and thermoelectric properties of TiFe2Sn Heusler alloy. Intermetallics (2021). https://doi.org/10.1016/j.intermet.2021.107195.10.1016/j.intermet.2021.107195 ↗
42. M. Parzer, F. Garmroudi, A. Riss, S. Khmelevskyi, T. Mori, and E. Bauer, High solubility of Al and enhanced thermoelectric performance due to resonant states in Fe2VAlx. Appl. Phys. Lett. 120, 071901 (2022).10.1063/5.0077159 ↗
43. R.B. Wilson and D.G. Cahill, Experimental validation of the interfacial form of the Wiedemann-Franz law. Phys. Rev. Lett. (2012). https://doi.org/10.1103/PhysRevLett.108.255901.10.1103/PhysRevLett.108.255901 ↗
44. M. Mikami, Y. Kinemuchi, K. Ozaki, Y. Terazawa, and T. Takeuchi, Thermoelectric properties of tungsten-substituted Heusler Fe2VAl alloy. J. Appl. Phys. (2012). https://doi.org/10.1063/1.4710990.10.1063/1.4710990 ↗
45. S. Masuda, K. Tsuchiya, J. Qiang, H. Miyazaki, and Y. Nishino, Effect of high-pressure torsion on the microstructure and thermoelectric properties of Fe2VAl-based compounds. J. Appl. Phys. (2018). https://doi.org/10.1063/1.5034390.10.1063/1.5034390 ↗
46. K. Fukuta, K. Tsuchiya, H. Miyazaki, and Y. Nishino, Improving thermoelectric performance of Fe2VAl-based Heusler compounds via high-pressure torsion. Appl. Phys. A 128, 184 (2022).10.1007/s00339-022-05329-y ↗
47. S. Ghosh, A. Nozariasbmarz, H. Lee, L. Raman, S. Sharma, R.B. Smriti, D. Mandal, Y. Zhang, S.K. Karan, N. Liu, J.L. Gray, M. Sanghadasa, Y. Xia, S. Priya, W. Li, and B. Poudel, High-entropy-driven half-Heusler alloys boost thermoelectric performance. Joule (2024). https://doi.org/10.1016/j.joule.2024.08.008.10.1016/j.joule.2024.08.008 ↗