journal article·2007-05-30

Design of Solder Joint Structure for Flip Chip Package with an Optimized Shear Test Method

Jong-Woong Kim, Seung-Boo Jung

Journal of Electronic Materials· Volume 36· Issue 6
Publisher page

Abstract

The structure of flip chip solder bumps was optimized in terms of shear height and shear speed using a shear test method with both experimental investigation and nonlinear, three-dimensional, finite element analysis being conducted. A representative, Pb-free solder composition, Sn-3.0Ag-0.5Cu, was used to optimize the shear test of the flip chip solder joints. Increasing the shear height, at a fixed shear speed, decreased the shear force, as did decreasing the shear speed, at a fixed shear height. These experimental and computational results supported the recommendation of low shear height and low shear speed condition for the shear testing of flip chip solder bumps. This optimized shear test method was applied to investigate the effect of various heights of mini bumps on the shear force of the solder joints. The shear force increased with increasing Ni-P mini bump height.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. K. Zeng, K.N. Tu, Mater. Sci. Eng. R 38, 55 (2002)10.1016/S0927-796X(02)00007-4 ↗
2. D.G. Kim, J.W. Kim, S.B. Jung, Mater. Sci. Eng., B 121, 204 (2005)10.1016/j.mseb.2005.03.033 ↗
3. Y. Lin, W. Liu, Y. Guo, F.G. Shi, IEEE Trans. Adv. Packag. 28, 79 (2005)10.1109/TADVP.2004.841670 ↗
4. D.S. Liu, C.Y. Ni, C.Y. Chen, Finite Elem. Anal. Des. 39, 661 (2003)10.1016/S0168-874X(02)00133-6 ↗
5. D.G. Yang, J.S. Liang, Q.Y. Li, L.J. Ernst, G.Q. Zhang, Microelectron. Reliab. 44, 1947 (2004)10.1016/j.microrel.2004.04.023 ↗
6. J.W. Kim, S.B. Jung, Mater. Sci. Eng. A 371, 267 (2004)10.1016/j.msea.2003.12.012 ↗
7. J.W. Kim, S.B. Jung, Mater. Sci. Eng. A 397, 145 (2005)10.1016/j.msea.2005.02.040 ↗
8. S.W. Ricky Lee, X. Huang, Solder. Surf. Mt. Technol. 14, 45 (2002)10.1108/09540910210416468 ↗
9. JESD22-B117, JEDEC Solid State Technology Association (USA), 2000
10. D.G. Kim, J.W. Kim, J.G. Lee, H. Mori, D.J. Quesnel, S.B. Jung, J. Alloy Compd. 395, 80 (2005)10.1016/j.jallcom.2004.11.038 ↗
11. M. He, W.H. Lau, G. Qi, Z. Chen, Thin Solid Films 462–463, 376 (2004)10.1016/j.tsf.2004.05.058 ↗
12. J.W. Kim, D.G. Kim, S.B. Jung, Microelectron. Reliab. 46, 535 (2006)10.1016/j.microrel.2005.06.008 ↗
13. H. Sakai, K. Nishimura, M. Motegi, and S. Sakuyama, Proc. 8th Symp. of Microjoining and Assembly Technology in Electronics (Yokohama: JWS, 2002) pp. 443–448
14. K.C. Chang, K.N. Chiang, IEEE Trans. Compon. Packag. Trans. 27, 373 (2004)10.1109/TCAPT.2004.828557 ↗
15. G.R. Johnson and W.H. Cook, Proc. 7th Int. Symp. on Ballistics (ADPA Hague, 1983), pp. 541–549
16. F.J. Zerilli, R.W. Armstrong, J. Appl. Phys. 61, 1816 (1987)10.1063/1.338024 ↗
17. S.R. Bodner, Y.J. Partom, J. Appl. Mech. 42, 385 (1975)10.1115/1.3423586 ↗
18. P.S. Symmonds, Behaviour of Materials under Dynamic Loading (New York: ASME, 1965), pp. 106–124