journal article·2013-07Open access

Stacked Micro Heat Exchange System for Optimized Thermal Coupling of MicroTEGs

N. Wojtas, M. Grab, W. Glatz, C. Hierold

Journal of Electronic Materials· Volume 42· Issue 7

Abstract

This study presents modeling and experimental results of micro thermoelectric generators (μTEGs) integrated into a multilayer micro heat exchange system. The multilayer configuration benefits from low heat transfer resistances at small fluid flow rates and at the same time from low required pumping powers. The compact stacked power device allows for high net output power per volume, and therefore a reduction in size, weight, and cost compared with conventional large-scale heat exchangers. The influence of the boundary conditions and the system design parameters on the net output power of the micro heat exchange system was investigated by simulation. The theoretical results showed a major impact of the microchannel dimensions and the μTEG thickness on the overall output performance of the system. By adapting the applied fluid flow rate, the system's net power output can be maximized for varying operating temperatures. Experimental measurements of the cross-flow micro heat exchange system were in good agreement with the performed simulations. A net μTEG output power of 62.9 mW/cm² was measured for a double-layer system at an applied water inlet temperature difference of 60 K with a Bi₂Te₃ μTEG (ZT of 0.12), resulting in a net volumetric efficiency factor of 37.2 W/m³/K². © 2013 TMS.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal Radiation and Cooling Technologies · Heat Transfer and Optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. R. Venkatasubramanian, E. Siivola, T. Colpitts, and B. O’Quinn, Nature 413, 6856 (2001).10.1038/35098012 ↗
2. K.F. Hsu, S. Loo, F. Guo, W. Chen, J.S. Dyck, C. Uher, T. Hogan, E.K. Polychroniadis, and M.G. Kanatzidis, Science 303, 5659 (2004).
3. D.M. Rowe, Int. J. Innov. Energy Syst. Power 1, 1 (2006).
4. J.W. Stevens, Energy Convers. Manage. 42, 6 (2001).10.1016/S0196-8904(00)00099-6 ↗
5. J.L. Yu and H. Zhao, J. Power Sour. 172, 1 (2007).10.1016/j.jpowsour.2007.05.082 ↗
6. F.K. Meng, L.G. Chen, and F.R. Sun, Energy 36, 5 (2011).
7. S. Belanger and L. Gosselin, Energy Convers. Manage. 52, 8–9 (2011).10.1016/j.enconman.2011.02.019 ↗
8. J. Esarte, G. Min, and D.M. Rowe, J. Power Sour. 93, 1–2 (2001).10.1016/S0378-7753(00)00566-8 ↗
9. X. Niu, J.L. Yu, and S.Z. Wang, J. Power Sour. 188, 2 (2009).
10. A. Tsuyoshi and K. Matsuura, Electr. Eng. Jpn. 141, 1 (2002).10.1002/eej.10042 ↗
11. D.T. Crane, J.W. LaGrandeur, F. Harris, and L.E. Bell, J. Electron. Mater. 38, 7 (2009).
12. W. Escher, D. Poulikakos, T. Brunschwiler, and B. Michel, J. Heat Trans. ASME 132, 8 (2010).10.1115/1.4001306 ↗
13. M. Strasser, R. Aigner, C. Lauterbach, T.F. Sturm, M. Franosch, and G. Wachutka, Sens. Actuators A 114, 2–3 (2004).10.1016/j.sna.2003.11.039 ↗
14. N. Wojtas, E. Schwyter, W. Glatz, S. Kühne, W. Escher, and C. Hierold, Sens. Actuators A: Phys. 188, (2012).10.1016/j.sna.2011.12.043 ↗
15. W. Glatz, E. Schwyter, L. Durrer, and C. Hierold, JMEMS 18, 3 (2009).