journal article·2012-06

Effect of Surface Preparation on Mechanical Properties of Ni Contacts on Polycrystalline (Bi1−x Sb x )2(Te1−y Se y )3 Alloys

S. Kashi, M. K. Keshavarz, D. Vasilevskiy, R. A. Masut, S. Turenne

Journal of Electronic Materials· Volume 41· Issue 6
Publisher page

Abstract

We present a comparison of different surface preparation techniques for hot-extruded (Bi1−xSbx)2(Te1−ySey)3 alloys prior to Ni plating and their consequences on adhesion. The surface preparation is carried out by a relatively fast and well-controlled electrochemical etching procedure that provides morphologies with homogeneous flat surfaces on a scale of tens of micrometers. This procedure is not optimal for Ni metallization since it does not ensure enough roughness on the surface. Applying wet chemical etching with hypochlorite and nitric acid after the electrochemical etching changes the morphology, and the surface roughness increases, as evidenced by scanning electron microscopy and atomic force microscopy. Tensile tests carried out on n-type and p-type 1-mm-thick specimens, covered with a 12-μm Ni layer followed by Sn-Pb soldered joints, confirm a significant improvement in the ultimate adhesion strength, with fracture occurring within the thermoelectric material. Use of this two-step surface treatment, after slicing and prior to metallization, leads to maximum adhesion strength of around 38 MPa for either type of thermoelectric material. These results are consistent with the morphological changes observed by scanning electron microscopy on the surface after chemical etching.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Thermoelectric Materials and Devices · Chalcogenide Semiconductor Thin Films · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (9)

Show source-provided references
1. H.J. Goldsmid, Introduction to Thermoelectricity (Heidelberg: Springer, 2010), pp. 79–111.10.1007/978-3-642-00716-3_6 ↗
2. A.A. Ascheulov and I.S. Romanyuk, J. Thermoelectr. 3, 68 (2004).
3. S. Turenne, T. Clin, D. Vasilevskiy, and R.A. Masut, J. Electron. Mater. 39, 1926 (2010).10.1007/s11664-009-1049-z ↗
4. D. Vasilevskiy, F. Roy, E. Renaud, R.A. Masut, and S. Turenne, ICT’06: XXV International Conference on Thermoelectrics, Proceedings, pp. 666–669, 725 (2006).
5. J. Faust and J.W. Praktische, Metallographie 3, 381 (1966).
6. K.C. Tewari, V.K. Gandotra, M.V.G. Padmavati, A. Singh, and A.G. Vedeshwar, Mater. Chem. Phys. 72, 72 (2001).10.1016/S0254-0584(01)00312-1 ↗
7. D. Ilzycer, A. Sher, and M. Shiloh, Third International Conference on Thermoelectric Energy Conversion (1980), pp. 200–202.
8. H.P. Feng, B. Yu, S. Chen, K. Collins, C. He, Z.F. Ren, and G. Chen, Electrochim. Acta 56, 3079 (2011).10.1016/j.electacta.2010.12.008 ↗
9. V. Semenyuk and O. Antonenko, 5th European conference on Thermoelectrics, Odessa, Ukraine (2007), pp. 90–93.