journal article·2020-06

A Novel Lining Method for Eliminating Plastic Deformation and Protrusion of Copper in Cu-TSV Using FEM Analysis

Yazdan Zare, Yasushi Sasajima, Jin Onuki

Journal of Electronic Materials· Volume 49· Issue 6
Publisher page

Abstract

Employing FEM analysis, a new lining method was invented to prevent plastic deformation and protrusion of copper in Cu-TSV after experiencing a thermal cycle (heating up from room temperature to 300°C and then cooling down to room temperature). Using this technique, thermal stresses exerted to the via were reduced to below the yield stress of copper, preventing copper from undergoing plastic deformation. Consequently, not only was the height of copper protrusion at 300°C decreased, but there was no extrusion bulge or dishing at the end of thermal cycle. Compared with traditional titanium barriers, copper protrusion at the end of thermal cycle decreased from 208.2 nm to 3.4 nm after the first thermal cycle and from 325.2 nm to (again) 3.4 nm after 10 successive thermal cycles.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: 3D IC and TSV technologies · Electronic Packaging and Soldering Technologies · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. H. Ilatikhameneh, T. Ameen, B. Novakovic, Y. Tan, G. Klimeck, and R. Rahman, Sci. Rep. 6, 31501 (2016). https://doi.org/10.1038/srep31501.10.1038/srep31501 ↗
2. N.Z. Haron and S. Hamdioui, in 2008 3rd International Design and Test Workshop, p. 98 (2008). https://doi.org/10.1109/idt.2008.480247510.1109/idt.2008.4802475 ↗
3. Ch Okoro, C. Huyghebaert, J.V. Olmen, R. Labie, K. Lambrinou, B. Vandevelde, E. Beyene, and D. Vandepitte, AIP Conf. Proc. 1300, 214 (2010). https://doi.org/10.1063/1.3527128.10.1063/1.3527128 ↗
4. T. Jiang, Ch Wu, L. Spinella, J. Im, N. Tamura, M. Kunz, H.Y. Son, B.G. Kim, R. Huang, and P.S. Ho, Appl. Phys. Lett. 103, 211906 (2013). https://doi.org/10.1063/1.4833020.10.1063/1.4833020 ↗
5. W.S. Kwon, D.T. Alastair, K.H. Teo, S. Gao, T. Ueda, T. Ishigaki, K. Kang, and W.S. Yoo, Appl. Phys. Lett. 98, 232106 (2011). https://doi.org/10.1063/1.3596443.10.1063/1.3596443 ↗
6. J.P. Gambino, S.A. Adderly, and J.U. Knickerbocker, Microelectron. Eng. 135, 73 (2015). https://doi.org/10.1016/j.mee.2014.10.019.10.1016/j.mee.2014.10.019 ↗
7. B. Liu, A. Satoh, K. Tamahashi, Y. Sasajima, and J. Onuki, Trans. Jpn. Inst. Electron. Packag. 11, E17-014-1 (2018). https://doi.org/10.5104/jiepeng.11.e17-014-1.10.5104/jiepeng.11.e17-014-1 ↗
8. E.J. Cheng and Y.L. Shen, Microelectron. Reliab. 52, 534 (2012). https://doi.org/10.1016/j.microrel.2011.11.001.10.1016/j.microrel.2011.11.001 ↗
9. P. Kumar, I. Dutta, and M.S. Bakir, J. Electron. Mater. 41, 322 (2012). https://doi.org/10.1007/s11664-011-1726-6.10.1007/s11664-011-1726-6 ↗
10. D. Kosemura and I. De Wolf, Appl. Phys. Lett. 106, 191901 (2015). https://doi.org/10.1063/1.4921004.10.1063/1.4921004 ↗
11. T. Jiang, S.K. Ryu, Q. Zhao, J. Im, R. Huang, and P.S. Ho, Microelectron. Reliab. 53, 53 (2013). https://doi.org/10.1016/j.microrel.2012.05.008.10.1016/j.microrel.2012.05.008 ↗
12. W. Feng, N. Watanabe, H. Shimamoto, M. Aoyagi, and K. Kikuchi, Microelectron. Reliab. 59, 95 (2016). https://doi.org/10.1016/j.microrel.2016.01.007.10.1016/j.microrel.2016.01.007 ↗
13. N. Ranganathan, K. Prasad, N. Balasubramanian, and K.L. Pey, J. Micromech. Microeng. 18, 075018 (2008). https://doi.org/10.1088/0960-1317/18/7/075018.10.1088/0960-1317/18/7/075018 ↗
14. P. Bayat, D. Vogel, R.D. Rodriguez, E. Sheremet, D.R.T. Zahn, S. Rzepka, and B. Michel, Microelectron. Eng. 137, 101 (2015). https://doi.org/10.1016/j.mee.2015.02.004.10.1016/j.mee.2015.02.004 ↗
15. C. Okoro, K. Vanstreels, R. Labie, O. Lühn, B. Vandevelde, B. Verlinden, and D. Vandepitte, J. Micromech. Microeng. 20, 045032 (2010). https://doi.org/10.1088/0960-1317/20/4/045032.10.1088/0960-1317/20/4/045032 ↗
16. S.K. Ryu, T. Jiang, K.H. Lu, J. Im, H.Y. Son, K.Y. Byun, R. Huang, and P.S. Ho, Appl. Phys. Lett. 100, 041901 (2012). https://doi.org/10.1063/1.3678020.10.1063/1.3678020 ↗
17. T. Jiang, S.K. Ryu, Q. Zhao, J. Im, P.S. Ho, and R. Huang, AIP Conf. Proc. 1601, 148 (2014). https://doi.org/10.1063/1.4881348.10.1063/1.4881348 ↗
18. X. Xu and A. Karmarkarb, AIP Conf. Proc. 1378, 53 (2011). https://doi.org/10.1063/1.3615695.10.1063/1.3615695 ↗
19. Y. Zare, Y. Sasajima, and J. Onuki, J. Electron. Mater. 49, 2076 (2020). https://doi.org/10.1007/s11664-019-07894-0.10.1007/s11664-019-07894-0 ↗
20. S.K. Ryu, K.H. Lu, J. Im, R. Huang, and P.S. Ho, AIP Conf. Proc. 1378, 153 (2011). https://doi.org/10.1063/1.3615702.10.1063/1.3615702 ↗
21. J. Auersperg, D. Vogel, E. Auerswald, S. Rzepka, and B. Michel, AIP Conf. Proc. 1601, 138 (2014). https://doi.org/10.1063/1.4881347.10.1063/1.4881347 ↗
22. T. Jiang, S.K. Ryu, J. Im, R. Huang, and P.S. Ho, AIP Conf. Proc. 1601, 55 (2014). https://doi.org/10.1063/1.4881340.10.1063/1.4881340 ↗
23. A. Satoh, H. Kadota, T. Inami, K. Tamahashi, M. Ito, and J. Onuki, Trans. Jpn. Inst. Electron. Packag. 9, E16-010-1 (2016). https://doi.org/10.5104/jiepeng.9.e16-010-1.10.5104/jiepeng.9.e16-010-1 ↗