journal article·2004-10

Correlation between interfacial reactions and mechanical strengths of Sn(Cu)/Ni(P) solder bumps

S. J. Wang, H. J. Kao, C. Y. Liu

Journal of Electronic Materials· Volume 33· Issue 10
Publisher page

Abstract

The correlation between interfacial reactions and mechanical strengths of Sn(Cu)/Ni(P) solder bumps has been studied. Upon solid-state aging, a diffusion-controlled process was observed for the interfacial Ni-Sn compound formation of the Sn/Ni(P) reaction couple and the activation energy is calculated to be 42 KJ/mol. For the Sn0.7Cu/Ni(P), in the initial aging, a needle-shaped Ni-Sn compound layer formed on Ni(P). Then, it was gradually covered by a layer of the Cu-Sn compound in the later aging process. Hence, a mixture layer of Ni-Sn and Cu-Sn compounds formed at the interface. For the Sn3.0Cu/Ni(P), a thick Cu-Sn compound layer quickly formed on Ni(P), which retarded the Ni-Sn compound formation and resulted in a distinct Cu-Sn compound/Ni(P) interface. The shear test results show that the mixture interface of Sn0.7Cu bumps have fair shear strengths against the aging process. In contrast, the distinct Cu-Sn/Ni(P) interface of Sn3.0Cu solder bumps is relatively weak and exhibits poor resistance against the aging process. Upon the reflowing process, the gap formation at the Ni(P)/Cu interface caused a fast degradation in the interfacial strength for Sn solder bumps. For Sn0.7Cu and Sn3.0Cu solder bumps, Ni3P formation was greatly retarded by the self-formed Cu-Sn compound layer. Therefore, Sn(Cu) solder bumps show better shear strengths over the Sn solder bump.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. K. Johal and J. Brewer (Paper presented at Proc. IPC Works 2000, Miami, FL, 2000).
2. C.Y. Lee and K.L. Lin, Thin Solid Films 249, 201 (1994).10.1016/0040-6090(94)90761-7 ↗
3. J.W. Jang, D.R. Frear, T.Y. Lee, and K.N. Tu, J. Appl. Phys. 88, 6359 (2000).10.1063/1.1321787 ↗
4. J.W. Jang, P.G. Kim, K.N. Tu, D.R. Frear, and P. Thompson, J. Appl. Phys. 85, 8456 (1999).10.1063/1.370627 ↗
5. Z. Mei, P. Callery, D. Fisher, F. Hua, and J. Glazer, Advances in Electronic Packaging, Proc. Pacific Rim/ASME Int. Intersociety Electronic Photonic Packaging Conf. (New York: ASME, 1997), pp. 543–1550.
6. Z. Mei, M. Kaufmann, A. Eslambolchi, and P. Johnson, Electronic Component and Technology Conf. (Piscataway, NJ: IEEE, 1998), pp. 952–961.
7. M.O. Alam, Y.C. Chan, and K.C. Hung, Microelectron. Reliab. 42, 1065 (2002).10.1016/S0026-2714(02)00068-9 ↗
8. D. Goyal, T. Lane, P. Kinzie, and C. Panichas, Proc. 52nd Electronic Component and Technology Conf. (Piscataway, NJ: IEEE, 2002), pp. 732–739.
9. Y.-D. Jeon and K.-W. Paik, 51st Electronic Component and Technology Conf. (Piscataway, NJ: IEEE, 2001), pp. 1326–1332.
10. S.J. Wang and C.Y. Liu, J. Electron. Mater. 32, 1303 (2003).10.1007/s11664-003-0027-0 ↗
11. K. Zeng, V. Vuorinen, and J.K. Kivilahti, IEEE Trans. Electron. Packaging Manufacturing 25, 162 (2002).10.1109/TEPM.2002.801648 ↗
12. H.D. Blair, T. Pan, and J.M. Nicholson, Electronic Components and Technology Conf. (Piscataway, NJ: IEEE, 1998), pp. 259–267
13. H. Matsukia, H. Ibukab, and H. Sakab, Sci. Technol. Adv. Mater. 3, 261 (2002).10.1016/S1468-6996(02)00025-6 ↗
14. S.J. Wang and C.Y. Liu, Scripta Mater. 49, 813 (2003).10.1016/S1359-6462(03)00486-X ↗
15. Solder Data Sheet, Welco Castings, Hamilton, ON, Canada.
16. D.R. Frear, S.N. Burchett, H.S. Morgan, and J.H. Lau, eds., The Mechanics of Solder Alloy Interconnects (New York: Van Nostrand Reinhold, 1994), p. 60.
17. D.E. Gray, ed., American Institute of Physics Handbook (New York: McGraw-Hill, 1957), pp. 2 ff-61 ff.
18. S.W. Chen, S.W. Lee, and M.C. Yip, J. Electron. Mater. 32, 1284 (2003).10.1007/s11664-003-0024-3 ↗