Optimization of black oxide coating thickness as an adhesion promoter for copper substrate in plastic integrated-circuit packages
Source abstract
Abstract
Copper-oxide coating applied onto the copper substrate has emerged as an alternative to metallic coatings to improve adhesion with polymeric adhesives and molding compounds. The interfacial-bond strengths between the black oxide-coated Cu substrate and epoxy-based, glob-top resin were measured in button-shear tests, and the failure mechanisms were identified from the fracture-surface examination. The emphasis was to establish the correlation between the coating thickness, the surface roughness, and the interfacial adhesion with respect to treatment time. It was found that at the initial stage of treatment a thin layer of flat, cuprous oxide developed, above which fibrillar-cupric oxide was formed with further treatment until saturation with densified fibrils at about 150 sec. The interfacial-bond strength between the oxide-coated copper substrate and glob-top resin increased gradually with increasing treatment time, until the bond strength reached a plateau constant after a treatment for about 150 sec. There was a functional similarity between the oxide thickness, the surface roughness, and the interface-bond strength with respect to treatment time. A treatment time of 150 sec is considered an optimal condition that can impart the highest interface adhesion.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Surface Modification and Superhydrophobicity · Material Properties and Processing
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. L.T. Nguyen, ASME J. Electron. Packaging 115, 346 (1993).10.1115/1.2909343 ↗
2. O. Yoshioka, N. Okabe, S. Nagayana, G. Murakami, and R. Yamagishi, 39th IEEE Electron. Comp. Technol. Conf. (Piscataway, NJ: IEEE, 1989), pp. 464–471.
3. B.J. Love and P.F. Packman, J. Adhes. 40, 139 (1993).10.1080/00218469308031280 ↗
4. S.I. Asai, T. Ando, and M. Tobita, J. Adhes. Sci. Technol. 10, 1 (1996).10.1163/156856196X00418 ↗
5. P. Eisler, The Technology of Printed Circuits (London: Heywood, 1959).
6. C.F. Coombs, Jr. Printed Circuit Handbook (New York: McGraw-Hill, 1979), pp. 33.1–33.21.
7. L.J. Slominski and A. Landau, Plating Surf. Finishing 69, 96 (1982).
8. R.D. Schueller and A.P. Plepys, Circuit World 2, 10 (1996).10.1108/03056129610799985 ↗
9. J.J. Bikerman, The Science of Adhesive Joints, 2nd ed. (New York: Academic Press, 1968), p. 139.
10. T.M. Tam and R.D. Robinson, Plating Surf. Finishing 73, 74 (1980).
11. A.H. Reed, Printed Circuit World Convention III, (1983).
12. K. McNutt, Printed Circuit Fabr. 18, 20 (1995).
13. M. Lebbai, J.K. Kim, and M.M.F. Yuen, J. Electron. Mater. (in this issue).
14. M. Lebbai, J.K. Kim, and M.M.F. Yuen, J. Electron. Mater. (in this issue).
15. D.J. O’Connor, B.A. Sexton, and R.St.C. Smart, editors, Surface Analysis Methods in Materials Science (Berlin: Springer-Verlag, 1992), pp. 203–248.
16. H.K. Yun, K. Cho, J.H. An, and C.E. Park, J. Mater. Sci. 27, 5811 (1992).10.1007/BF01119743 ↗
17. B.J. Love and P.F. Packman, J. Mater. Sci. 33, 1359 (1998).10.1023/A:1004366818593 ↗
18. M. Lebbai, J.K. Kim, and W.K. Szeto, J. Adhes. Sci. Technol. (in press).
19. H.Y. Lee and J. Yu, J. Electron. Mater. 28, 1444 (1999).10.1007/s11664-999-0138-3 ↗
20. A.J. Kinloch, J. Mater. Sci. 15, 2141 (1980).10.1007/BF00552302 ↗
21. J.K. Kim and Y.W. Mai, Engineered Interfaces in Fibre Reinforced Composites (Oxford, U.K.: Elsevier, 1998), pp. 5–41.10.1016/B978-008042695-2/50003-8 ↗