Frictions stir welding of copper under different welding parameters and media
Source abstract
Abstract
Defect free friction stir welding of pure copper plates was conducted in air condition at a rotation speed of 1600 rev min−1 and traverse speeds of 50 and 100 mm min−1. The microstructural and mechanical properties of defect free joints produced in air and underwater conditions were compared. The results revealed that a finer microstructure can be achieved by underwater friction stir welding. The hardness of joints welded in both conditions was higher compared to the base metal. Moreover, in comparison with the base metal, the joints welded in air and underwater conditions exhibited lower and higher tensile properties respectively.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Materials Engineering, Sahand University of Technology, Tabriz, Iran
References (28)
Show source-provided references
1. 10.1016/j.matdes.2010.03.02710.1016/j.matdes.2010.03.027 ↗
2. 10.1007/s11661-010-0254-y10.1007/s11661-010-0254-y ↗
3. 10.1016/j.jmatprotec.2010.05.01910.1016/j.jmatprotec.2010.05.019 ↗
4. 10.1016/j.msea.2012.03.09410.1016/j.msea.2012.03.094 ↗
5. 10.1016/j.mser.2005.07.00110.1016/j.mser.2005.07.001 ↗
6. 10.1016/j.pmatsci.2008.05.00110.1016/j.pmatsci.2008.05.001 ↗
7. 10.1016/j.scriptamat.2011.02.01910.1016/j.scriptamat.2011.02.019 ↗
8. 10.1016/j.matdes.2011.09.05810.1016/j.matdes.2011.09.058 ↗
9. 10.1016/j.matdes.2012.09.01010.1016/j.matdes.2012.09.010 ↗
10. 10.1179/136217109X45695110.1179/136217109X456951 ↗
11. 10.1179/136217109X40042010.1179/136217109X400420 ↗
12. 10.1179/1362171810Y.000000000510.1179/1362171810Y.0000000005 ↗
13. 10.1179/136217109X1257781448661010.1179/136217109X12577814486610 ↗
14. 10.1179/1362171811Y.000000008910.1179/1362171811Y.0000000089 ↗
15. Okamoto K, Doi M, Hirano S, Aota K, Okamura H, Aono Y: ‘Fabrication of backing plate of copper alloy by friction stir welding’, Proc. 3rd Int. Symp. on ‘Friction stir welding’, Kobe, Japan, September 2001, 27–28.
16. 10.1016/j.matlet.2003.08.01410.1016/j.matlet.2003.08.014 ↗
17. 10.1007/s10853-007-1666-y10.1007/s10853-007-1666-y ↗
18. 10.1007/s11663-012-9755-y10.1007/s11663-012-9755-y ↗
19. 10.1016/j.matdes.2012.12.02610.1016/j.matdes.2012.12.026 ↗
20. 10.1016/j.matdes.2011.06.02110.1016/j.matdes.2011.06.021 ↗
21. 10.1016/j.matdes.2011.03.07310.1016/j.matdes.2011.03.073 ↗
22. 10.1016/j.msea.2009.10.03910.1016/j.msea.2009.10.039 ↗
23. 10.1016/S1003-6326(09)60309-510.1016/S1003-6326(09)60309-5 ↗
24. 10.1016/j.matdes.2011.12.02210.1016/j.matdes.2011.12.022 ↗
25. 10.1016/j.matdes.2010.08.02810.1016/j.matdes.2010.08.028 ↗
26. 10.1016/j.scriptamat.2007.03.04810.1016/j.scriptamat.2007.03.048 ↗
27. 10.1016/j.msea.2012.03.09410.1016/j.msea.2012.03.094 ↗
28. 10.1016/j.matdes.2010.05.00710.1016/j.matdes.2010.05.007 ↗