Key factors influencing mechanical performance of dual phase steel resistance spot welds
Source abstract
Abstract
Quasi-static tensile shear mechanical properties of resistance spot welds of three dual phase (DP) grades including DP600, DP780 and DP980 are investigated. Results showed that weld fusion zone size, failure mode and the strength/ductility of failure location are the main factors governing the peak load and the energy absorption of spot welds. Heat affected zone (HAZ) softening plays an important role in mechanical properties of DP steels with higher volume fraction of martensite (i.e. DP780 and DP980). It was shown that the peak load of the spot welds is not proportionally correlated to the tensile strength of the base metal. Pronounced HAZ softening in DP980 resulted in reducing its tendency to fail in interfacial failure mode in comparison to DP780. In addition, despite its lower base metal ductility, DP980 weld exhibits enhanced ductility and energy absorption than DP780 due to its pronounced HAZ softening.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Young Researchers Club, Islamic Azad University, Dezful Branch, Dezful, Iran
Mining and Metallurgical Engineering Department, Amirkabir University of Technology, Tehran, Iran
References (35)
Show source-provided references
1. 10.1007/s11661-001-0067-010.1007/s11661-001-0067-0 ↗
2. Tumuluru M. D. · Weld. J · 2007 · 86 · 31
3. 10.1179/174329307X24934210.1179/174329307X249342 ↗
4. 10.1016/j.engfailanal.2007.01.01810.1016/j.engfailanal.2007.01.018 ↗
5. 10.1179/174329307X16440910.1179/174329307X164409 ↗
6. Zuniga S., and Sheppard S. D.: in ‘Fatigue and fracture mechanics’, Vol. 27, ASTM STP 1296, (ed. R. S. Piascik et al.), 469–489; 1997, Philadelphia, USA, ASTM.10.1520/STP16249S ↗
7. 10.1115/1.213775110.1115/1.2137751 ↗
8. Zuniga S. M. ‘Predicting overload pull-out failures in resistance spot welded’, PhD thesis, Stanford University, Palo Alto, CA, 1994.
9. 10.1016/j.engfracmech.2004.07.01310.1016/j.engfracmech.2004.07.013 ↗
10. 10.1007/BF0264883210.1007/BF02648832 ↗
11. 10.1016/j.jmatprotec.2008.11.01710.1016/j.jmatprotec.2008.11.017 ↗
12. Marya M. · Weld. J · 2005 · 172s
13. Marya M. · Weld J · 2005 · 197s
14. 10.1179/174329307X15980110.1179/174329307X159801 ↗
15. 10.1179/174329306X12089510.1179/174329306X120895 ↗
16. 10.1016/j.msea.2007.08.01010.1016/j.msea.2007.08.010 ↗
17. Pakalnins E., and Morrisette T. ‘Comparative resistance spot weld characterization of 600 MPa dual-phase steels using DOE analysis’, Proc. 11th Int. Conf. on ‘Sheet metal welding’, Livonia, MI, May 2004, AWS, Paper 1–3.
18. ‘Specification for metal-arc welding of carbon and carbon manganese steels’, BS5135, British Standard Institute, London, 1974.
19. ‘Recommended practices for test methods and evaluation the resistance spot welding behavior of automotive sheet steels’, ANSI/AWS/SAE D8·9–97, 1997.
20. 10.1179/174329308X27173310.1179/174329308X271733 ↗
21. Radakovic D. J. · Weld. J · 2008 · 96s
22. Joaquin A. · Weld. J · 2007 · 86 · 24
23. Pouranvari M., Marashi P., Goodarzi M., and Bahmanpour H. ‘Metallurgical factors affecting failure mode of resistance spot welds’, Proc. Conf. on ‘Materials science and technology’, Pittsburgh, PA, USA, October 2008, AcerS/AIST/ASM/TMS, 2465–2475.
24. Sun X. · Weld. J · 2004 · 188s
25. 10.2355/isijinternational.48.80910.2355/isijinternational.48.809 ↗
26. Kunishige K., Yamauchi N., Taka T., and Nagao N. ‘Softening in weld heat affected zone of dual phase steel sheet for automotive wheel rim’, SAE paper no. 830632, SAE, Warrendale, PA, USA, 1983.10.4271/830632 ↗
27. Kapustka N. · Weld J · 2008 · 135s
28. Wibowo M. K. · Adv. Mater. Res · 2007 · 15
29. 10.1016/j.matlet.2009.10.04010.1016/j.matlet.2009.10.040 ↗
30. 10.1016/j.engfracmech.2006.03.01710.1016/j.engfracmech.2006.03.017 ↗
31. Nikoosohbat F. · Mater. Sci. Technol
32. Sun X. · Weld. J · 2007 · 18s
33. 10.1179/136217108X32547010.1179/136217108X325470 ↗
34. Heuschkel J. · Weld. J · 1952 · 931s
35. Sawhill J. M. · Weld. J · 1980 · 19ss