journal article·2025-02-10Open access

Self-compacting mortar overlays using expanded polystyrene beads for thermal performance and energy efficiency in buildings

Syed Ali Rizwan, Muhammad Nasir Amin, Hafiz Sajid Ali, Hamza Ali, Muhammad Tahir Qadir, Muhammad Imran

Abstract

Abstract This study presents a novel approach for building thermal retrofitting using self-compacting mortar overlays (SCMO) incorporating low-volume expanded polystyrene beads (EPSBs). Unlike previous high-volume EPSBs concrete applications (20–80 % replacement), this research focuses on thin overlay systems using minimal EPSB content (0.1–0.2 % by binder mass) to achieve thermal benefits without structural compromise. 10 SCMO formulations were developed using three EPSBs sizes (3, 6, 9 mm) with Acacia Nilotica gum as a natural viscosity enhancer. Results revealed that all mixtures having polycarboxylate-ether superplasticizer achieved target flow of 30 ± 1 cm using Hagerman’s cone of size (6 × 7 × 10) cm 3 . Comprehensive testing revealed that EPSBs incorporation resulted in increased superplasticizer demand (0.75–0.90 %), extended setting times (93–210 min delay), and reduced compressive strength (50.5–21.9 MPa for largest beads of size 9 mm). However, thermal conductivity decreased significantly from 0.1589 W/m·K (control) to 0.0615 W/m·K (9 mm EPSBs), representing 61.3 % reduction. Early shrinkage testing showed beneficial strain accommodation with EPSBs inclusion. The data presented enables the selection of suitable EPSBs size in SCMO of varying selectable thicknesses. Heat transfer analysis demonstrated energy consumption reductions of 36.3 %, 46.8 %, and 61.3 % for 3, 6, and 9 mm EPSBs sizes, respectively, in 38 mm overlay applications. The results establish SCMO as practical solutions for building thermal retrofitting, offering superior applicability compared to rigid insulation boards while maintaining adequate mechanical properties for overlay applications. This research provides the first systematic evaluation of low-volume EPSBs systems specifically designed for thin overlay thermal retrofitting. The strength reduction can be minimized by using synergy of supplementary cementitious materials, as has been demonstrated by authors in previous studies.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Concrete and Cement Materials Research · Concrete Properties and Behavior · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Civil Engineering , National University of Computer & Emerging Sciences (NUCES-FAST) , Lahore , Pakistan

School of Civil and Environmental Engineering (SCEE), NUST Institute of Civil Engineering (NICE), National University of Sciences and Technology (NUST) , Sector H-12 , Islamabad , Pakistan

Department of Civil and Environmental Engineering , College of Engineering, King Faisal University , 31982 , Al Ahsa , Saudi Arabia

Funding

The Deanship of Scientific Research, Vice Presidency for Graduate Studies and Scientific Research, King Faisal University, Saudi Arabia · NUCES-FAST Lahore, Pakistan · NUST Islamabad, Pakistan

References (45)

Show source-provided references
1. Yang, J, Chan, K, Venkatesan, H, Kim, E, Adegun, MH, Lee, J, et al.. Superinsulating BNNS/PVA composite aerogels with high solar reflectance for energy-efficient buildings. Nano-Micro Lett 2022;14:54. https://doi.org/10.1007/s40820-022-00797-6.10.1007/s40820-022-00797-6 ↗
2. Torres, M, Lombard, LP, Coronel, JF, Maestre, IR, Yan, D. A review on buildings energy information: trends, end-uses, fuels and drivers. Energy Rep 2022;8:626–37. https://doi.org/10.1016/j.egyr.2021.11.280.10.1016/j.egyr.2021.11.280 ↗
3. Rodgers, L. Climate change: the massive CO2 emitter you may not know about. BBC News 17 December 2018. https://www.bbc.com/news/science-environment-46455844.
4. Tanuj, V, Khitoliya, DR, Singh, AJ. An evaluative study on energy efficient building materials. Int J Innov Res Adv Eng (IJIRAE) 2016;3:98–103.
5. Shen, X, Kim, J-K. 3D graphene and boron nitride structures for nanocomposites with tailored thermal conductivities: recent advances and perspectives. Funct Compos Struct 2020;2:022001. https://doi.org/10.1088/2631-6331/ab953a.10.1088/2631-6331/ab953a ↗
6. Yüksek, I. An evaluation of building materials in terms of energy efficiency. Period Polytech Civ Eng 2015;59:45–58. https://doi.org/10.3311/ppci.7050.10.3311/PPci.7050 ↗
7. Rizwan, SA, Ahmad, S, Bier, TA. Application of packing concepts to high performance self-consolidating mortar (SCM) systems. USA: ACI Special Publication; 2012, 289:1–17 pp.
8. Gupta, N, Siddique, R, Belarbi, R. Sustainable and greener self-compacting concrete incorporating industrial by-products: a review. J Clean Prod 2021;284:124803. https://doi.org/10.1016/j.jclepro.2020.124803.10.1016/j.jclepro.2020.124803 ↗
9. Rizwan, SA, Khan, H, Bier, TA, Adnan, F. Use of effective Micro-organisms (EM) technology and self-compacting concrete (SCC) technology improved the response of cementitious systems. Constr Build Mater 2017;152:642–50. https://doi.org/10.1016/j.conbuildmat.2017.05.102.10.1016/j.conbuildmat.2017.05.102 ↗
10. Chen, B, Liu, J. Mechanical properties of polymer-modified concretes containing expanded polystyrene beads. Constr Build Mater 2007;21:7–11. https://doi.org/10.1016/j.conbuildmat.2005.08.001.10.1016/j.conbuildmat.2005.08.001 ↗
11. Shabbar, R, Al-Tameemi, AA, Alhassani, AMJ. The effect of expanded polystyrene beads (EPS) on the physical and mechanical properties of aerated concrete. Open Eng 2022;12:424–30. https://doi.org/10.1515/eng-2022-0020.10.1515/eng-2022-0020 ↗
12. Hu, F, Wu, S, Sun, Y. Hollow-structured materials for thermal insulation. Adv Mater 2019;31:1801001. https://doi.org/10.1002/adma.201801001.10.1002/adma.201801001 ↗
13. Herihiri, O, Guettala, A, Benabed, B. An investigation on the physical, mechanical and thermal properties of dune sand mortars lightened by expanded polystyrene beads (EPS). J Silic Based Compos Mater 2021;1:28–36. https://doi.org/10.14382/epitoanyag-jsbcm.2021.6.10.14382/epitoanyag-jsbcm.2021.6 ↗
14. Sabaa, B, Ravindrarajah, RS. Engineering properties of lightweight concrete containing crushed expanded polystyrene waste. In: Proceedings of the symposium on Advances in Materials for cementitious composites, December 11–13, 1997. Boston, MA, USA: Materials Research Society; 1997.
15. Hilal, N, Sor, NH, Faraj, RH. Development of eco-efficient lightweight self-compacting concrete with high volume of recycled EPS waste materials. Environ Sci Pollut Control Ser 2021;28:50028–51. https://doi.org/10.1007/s11356-021-14213-w.10.1007/s11356-021-14213-w ↗
16. Babu, D, Babu, KG, Weea, TH. Properties of lightweight expanded polystyrene aggregate concretes containing fly ash. Cement Concr Res 2005;35:1218–23.10.1016/j.cemconres.2004.11.015 ↗
17. Melit, L, Calotă, R, Amăreanu, M, Silica aerogel-incorporated cement and lime plasters for building insulation: an experimental study, Buildings 2024;14:1-12.10.3390/buildings14082300 ↗
18. Gu, X, Ling, Y. Research progress of aerogel materials in the field of construction. Alex Eng J 2024;91:620–31. https://doi.org/10.1016/j.aej.2024.02.039.10.1016/j.aej.2024.02.039 ↗
19. Simpson, A, Rattigan, I, Kalavsky, E, Parr, G. Thermal conductivity and conditioning of grey expanded polystyrene foams. Cell Polym 2020;39:238–62. https://doi.org/10.1177/0262489320934263.10.1177/0262489320934263 ↗
20. Erünal, E. Comparison of thermal insulation performance of foam extruded Black EPS. Polym Bull 2024;81:16595–605.10.1007/s00289-024-05485-6 ↗
21. Huang, Y, Stonehouse, A, Abeykoon, C. Encapsulation methods for phase change materials – a critical review. Int J Heat Mass Tran 2023;200:620–31. https://doi.org/10.1016/j.ijheatmasstransfer.2022.123458.10.1016/j.ijheatmasstransfer.2022.123458 ↗
22. Aftab, W, Huang, X, Wu, W, Liang, Z, Mahmood, A, Zou, R. Nanoconfined phase change materials for thermal energy applications. Energy Environ Sci 2018;11:1392–424. https://doi.org/10.1039/c7ee03587j.10.1039/C7EE03587J ↗
23. Rizwan, SA, Latif, W, Bier, TA. Response of self-consolidating cement paste systems containing Acacia nilotica gum as an organic admixture. Constr Build Mater 2016;126:768–76. https://doi.org/10.1016/j.conbuildmat.2016.09.097.10.1016/j.conbuildmat.2016.09.097 ↗
24. Rizwan, SA, Neha Mahmood, UM, Bier, TA. Response of self-compacting paste (SCP) systems containing Acacia modesta gum. Constr Build Mater 2018;161:398–406. https://doi.org/10.1016/j.conbuildmat.2017.11.145.10.1016/j.conbuildmat.2017.11.145 ↗
25. Rizwan, SA, Gul, S, Bier, TA. Self-consolidating paste systems containing Acacia nilotica gum powder. ACI Mater J 2019;116:5–15.10.14359/51706841 ↗
26. Tomori, MA, Adedeji, AA. Assessment of early compressive strength of self-compacting concrete using different grades of ordinary Portland cement. Webs Journal of Science and Engineering Application 2015;4:252–68.
27. SCC 028. The European guidelines for self-compacting concrete. BIBM, CEMBUREAU, ERMCO, EFCA, and EFNARC; May 2005.
28. BS EN 196-3. A method of testing cement. Part 3: determination of setting times and soundness. UK: BSI; 1995.
29. BS EN 196-1. Method of determining compressive and flexural strength of cement mortar. UK: BSI; 2005.
30. Aalmusallam, A. Effect of environmental conditions on the properties of fresh and hardened concrete. Cement Concr Compos 2001;23:353–61. https://doi.org/10.1016/s0958-9465(01)00007-5.10.1016/S0958-9465(01)00007-5 ↗
31. Bergström, SG. Curing temperature, age and strength of concrete. Magazine of Confrence Research 1953;5:61–6. https://doi.org/10.1680/macr.1953.5.14.61.10.1680/macr.1953.5.14.61 ↗
32. Tuaum, A, Haileselassie, B, Tsehaye, Y. Experimental investigation of rigid concrete pavements incorporated with waste lathe scrap steel fiber. In: 1st International conference on Engineering and Technology, Ethiopia: Research Gate; 2020:124–35 pp.
33. Marchment, T, Sanjayan, JG, Nematollahi, B, Xia, M. Interlayer strength of 3D printed concrete. In: Sanjayan J, Nazari A, Nematollahi B, editors. 3D concrete printing technology. Oxford, UK: Elsevier; 2019: 241–64 pp. ISBN 9780128154816.10.1016/B978-0-12-815481-6.00012-9 ↗
34. Rizwan, SA. High-performance mortars and concrete using secondary raw materials [Ph.D thesis]. Germany: Technical University Freiberg; 2006. 161 pp.
35. Mahmood, U, Bier, T, Rizwan, S. Assessing rheology of self-compacting paste systems—A new approach. ACI Mater J;118:2021.10.14359/51732793 ↗
36. Ferraris, FC, de Larrard, F. Testing and modelling of fresh concrete rheology, NISTIR 6094, February 1998. SCIRP Open Access March 2011;3.10.6028/NIST.IR.6094 ↗
37. Liu, N, Chen, B. Experimental study of the influence of EPS particle size on the mechanical properties of EPS lightweight concrete. Constr Build Mater 2014;68:227–32. https://doi.org/10.1016/j.conbuildmat.2014.06.062.10.1016/j.conbuildmat.2014.06.062 ↗
38. Sora, NH, Hilal, N, Faraj, RH, Ahmed, HU, Sherwani, AFH. Experimental and empirical evaluation of strength for sustainable lightweight self-compacting concrete by recycling high volume of industrial waste materials. Eur J Environ Civ Eng 2021:1–18.
39. Kheir, J, Hilloulin, B, Loukili, A, Belie, ND. Chemical shrinkage of low water to cement (w/c) ratio CEM I and CEM III cement pastes incorporating silica fume and filler. Materials 2021;14:1164. https://doi.org/10.3390/ma14051164.10.3390/ma14051164 ↗
40. Lura, P. Autogenous strain of cement pastes with superabsorbent polymers. In: International RILEM conference on volume changes of hardening concrete: testing and mitigation. Denmark: Lyngby DTU; 2006:57–65 pp.10.1617/2351580052.007 ↗
41. Elyamany, HE, Elmoaty, AEMA, Mohamed, B. Effect of filler types on physical, mechanical and microstructure of self-compacting concrete and flowable concrete. Alex Eng J 2014;53:295–307. https://doi.org/10.1016/j.aej.2014.03.010.10.1016/j.aej.2014.03.010 ↗
42. Sharaf, F. The impact of thermal mass on building energy consumption: a case study in Al Mafraq city in Jordan. Cogent Eng 2020;7:1–18. https://doi.org/10.1080/23311916.2020.1804092.10.1080/23311916.2020.1804092 ↗
43. Ali, HS. Study of energy efficient SCM systems. [M.Sc. thesis]. Lahore: NUCES-FAST; 2021:1–75 pp.
44. Faheem, A, Rizwan, SA, Beir, TA. Properties of self-compacting mortars using blends of limestone powder, fly ash, and zeolite powder. J Constr Build Mater 2021;286:122788. https://doi.org/10.1016/j.conbuildmat.2021.122788.10.1016/j.conbuildmat.2021.122788 ↗
45. Rizwan, SA, Beir, TA. Blends of limestone powder and fly-ash enhance the response of self-compacting mortars. Constr Build Mater 2012;27:398–403. https://doi.org/10.1016/j.conbuildmat.2011.07.030.10.1016/j.conbuildmat.2011.07.030 ↗