journal article·2008-09

Hydriding/dehydriding behavior of Mg2CoH5 produced by reactive mechanical milling

I. González Fernández, G.O. Meyer, F.C. Gennari

Journal of Alloys and Compounds· Volume 464· Issue 1-2
Publisher page

Abstract

Abstract Complex Mg 2 CoH 5 hydride was obtained by a combined procedure that included a milling stage of a 2Mg–Co mixture under argon followed by reactive mechanical alloying (RMA) under hydrogen, both at room temperature. During RMA, MgH 2 is produced at short milling times (10 h) and Mg 2 CoH 5 (50 wt%) after 90 h. Improvement in the yield and the formation times could be associated with both refinement of microstructure and enhancement of intermixing of Mg–Co during pre-milling stage. DSC studies of Mg 2 CoH 5 phase produced by RMA show that the starting decomposition temperature is about 205 °C. Absorption and desorption PCIs were determined under static (300 °C) and dynamic (230–330 °C) conditions. An important hysteresis and two plateaus were observed and correlated with formation/decomposition of Mg 2 CoH 5 (high-pressure plateau) and Mg 6 Co 2 H 11 (low-pressure plateau) hydrides. For comparing hydrogen sorption kinetics, Mg 2 CoH 5 (65 wt%) was also obtained by a sintering method at 410 °C and 6.0 MPa of hydrogen pressure. Absorption was very fast in the temperature range of 150–350 °C, independently of synthesis procedure. However, desorption curves showed a better behavior for RMA powders. MgCo was observed after decomposition of Mg 2 CoH 5 under particular thermal treatments, while MgCo 2 phase was not detected. The results of this study reinforce the idea that kinetics factors related with atomic mobility play a key role in the formation of Mg–Co intermetallics.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen Storage and Materials · Ammonia Synthesis and Nitrogen Reduction · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Schlapbach y · Nature · 2001 · 414 · 35310.1038/35104634 ↗
2. Fichtner · Adv. Eng. Mater. · 2005 · 7 · 44310.1002/adem.200500022 ↗
3. Yvon · 2004 · 1
4. Zolliker · Inorg. Chem. · 1985 · 24 · 417710.1021/ic00218a039 ↗
5. Ivanov · Inorg. Chem. · 1989 · 28 · 61310.1021/ic00302a046 ↗
6. Černý · J. Alloys Compd. · 1992 · 187 · 23310.1016/0925-8388(92)90537-J ↗
7. 1990
8. Selvam · Int. J. Hydrogen Energy · 1991 · 16 · 61510.1016/0360-3199(91)90085-W ↗
9. Huot · J. Alloys Compd. · 1997 · 248 · 16410.1016/S0925-8388(96)02705-3 ↗
10. Chen · J. Mater. Sci. · 2001 · 36 · 582910.1023/A:1012960206480 ↗
11. Shao · J. Solid State Chem. · 2004 · 177 · 362610.1016/j.jssc.2004.05.003 ↗
12. Gennari · J. Alloys Compd. · 2005 · 396 · 18210.1016/j.jallcom.2004.12.027 ↗
13. González Fernández · J. Alloys Compd. · 2007 · 446–447 · 10610.1016/j.jallcom.2006.12.007 ↗
14. Meyer · 1996 · 1293
15. Gennari · J. Alloys Compd. · 2001 · 231 · 4610.1016/S0925-8388(00)01460-2 ↗
16. Gennari · J. Alloys Compd. · 2002 · 339 · 26110.1016/S0925-8388(01)02009-6 ↗
17. Yoshida · J. Alloys Compd. · 1993 · 190 · L4510.1016/0925-8388(93)90389-5 ↗