journal article·2025-12Open access

Theoretical and experimental mechanical properties and thermal conductivity of W-Al-B thin films deposited by magnetron sputtering

Ewa Wojtiuk, Marcin Maździarz, Tomasz Stasiak, Marcin Brykała, Marcin Chmielewski, Mateusz Włoczewski, Anna Kosińska, Katarzyna Zielińska, Oksana Haponova, Jarosław Jasiński, Tomasz Mościcki

Abstract

This work compares experimentally measue properties of W-Al-B thin films with mechanical properties, density, and thermal conductivity values calculated using DFT methods. Theoretical modelling was conducted to simulate two WB 2 stable structures alloyed with varying amounts of aluminium: α-WB 2 (P6/mmm) and ω-WB 2 (P6 3 /mmc), as well as α-AlB 2 (P6/mmm). Using the HiPIMS-DC magnetron sputtering technique, films with α-WB 2 structure and varying aluminium contents were deposited at 400 °C. When layers are composed with x = 1.4% aluminium (where x = at%Al / (at%Al + at%W)), their microstructure changes from amorphous to crystalline columnar. A back transformation to an amorphous microstructure occurs when the amount of aluminium exceeds x = 7.3%. An original method was used for the film density studies, which combined mass measurements and microscopic observation. These measurements were then used to determine the layers' thermal conductivity using the thermoreflectance method. The measured conductivity of the deposited ceramic films range from 3 to 6 W/(mK). Moreover, the obtained films are very hard, e.g. H = 36.1 ± 1.7 GPa for x = 1.4% Al, but exhibit a much lower Young's modulus than the theoretical values. The relatively high H/E⁎ ratio > 0.1 for films with low aluminium content indicates anmore elastic character. Ab-initio calculations showed that, based on the criteria of Cauchy pressure (C 12 -C 44 ) and Pugh's ratio (B/G), the α-WB 2 structure may have a ductile nature in contrast to the other structures. However, the deposited films are rather brittle in nature, resulting from an excess of boron. The fracture toughness measurements show higher K IC values for low aluminium content. They are 3.8 MPa√m for WB 2 , 2.8 MPa√m for x = 1.4%, and 3 MPa√m for x = 7.3% aluminium. • Stiffness tensors of thermally and mechanically stable W 1-x Al x B 2 compounds were determined • Increase of thermal conductivity and density decrease with growing aluminium content • High H/E ⁎ >0.1 of magnetron sputtered hard (H=34.1±0.7 GPa) W 0.927 Al 0.073 B 2.8 films • 1.4% of Al addition causes the change of microstructure to crystalline at 400 °C • Brittle/ductile character of DFT modelled α-W-Al-B 2 vs. brittle behaviour of films
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Boron and Carbon Nanomaterials Research · Advanced ceramic materials synthesis · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. Structure and properties of the films based on ternary transition metal borides: theory and experiment10.5488/CMP.26.22701 ↗
2. New tungsten borides, their stability and outstanding mechanical properties10.1021/acs.jpclett.8b01262 ↗
3. The crucial influence of Al on the high-temperature oxidation resistance of Ti1-xAlxBy diboride thin films (0.36 ≤ x ≤ 0.74, 1.83 ≤ y ≤ 2.03)
4. Metastable AlB2 structured TM-Si-B2±z (TM = Ti, Zr, Hf) solid solutions from first-principles10.1016/j.actamat.2025.120857 ↗
5. Enhanced hardness and fracture toughness in diboride superlattice films: Ab initio and experimental study10.1016/j.surfcoat.2025.132607 ↗
6. Shear-activated phase transformations of diborides via machine-learning potential molecular dynamics10.1016/j.actamat.2025.121606 ↗
7. Machine-learning potentials predict orientation- and mode-dependent fracture in refractory diborides10.1016/j.actamat.2025.121568 ↗
8. Influence of Tantalum on phase stability and mechanical properties of WB210.1557/mrc.2019.5 ↗
9. Effect of titanium and deposition parameters on microstructure and mechanical properties of W-Ti-B thin films deposited by High Power Impulse Magnetron Sputtering10.1016/j.surfcoat.2024.130915 ↗
10. Structure determination of the 4d metal diborides: a quantum mechanical study10.1021/jp056652x ↗
11. Ab initio inspired design of ternary boride thin films10.1038/s41598-018-27426-w ↗
12. Effect of zirconium doping on the mechanical properties of W1−xZrxB2 on the basis of first-principles calculations and magnetron sputtered films
13. Phase stability and mechanical properties of tungsten borides from first principles calculations10.1039/c004122j ↗
14. Superhard tungsten diboride-based solid solutions10.1021/acs.inorgchem.8b02620 ↗
15. W-ion irradiation promotes dense TiBx film growth during magnetron sputtering without substrate heating10.1016/j.surfcoat.2025.131766 ↗
16. Superhard oxidation-resistant Ti1-xAlxBy thin films grown by hybrid HiPIMS/DCMS co-sputtering diboride targets without external substrate heating
17. P. H. Mayrhofer, Influence of co-sputtering AlB2 to TaB2 on stoichiometry of non-reactively sputtered boride thin films10.1080/21663831.2024.2357700 ↗
18. Electron-configuration stabilized (W,Al)B2 solid solutions10.1016/j.actamat.2019.05.056 ↗
19. Microstructure, mechanical properties, thermal decomposition and oxidation sequences of crystalline AlB2 thin films
20. Microstructure and mechanical properties of cr-w-b-n coating deposited by dc reactive magnetron co-sputtering10.4028/www.scientific.net/AMR.651.430 ↗
21. Structure evolution and mechanical properties of Al-alloyed tantalum diboride films prepared by magnetron sputtering co-deposition10.1116/6.0002390 ↗
22. Evolution of structure and mechanical properties of hard yet fracture resistant w-b-c coatings with varying c/w ratio10.1016/j.surfcoat.2018.02.054 ↗
23. WTaB coatings as effective solutions for increasing die durability in lead-free brass alloy flashless hot forging process10.1016/j.wear.2025.205849 ↗
24. Characterization and wear response of magnetron sputtered w–b and w–ti–b coatings on wc–co tools10.3390/coatings10121231 ↗
25. Designing thin film materials — Ternary borides from first principles10.1016/j.tsf.2015.03.035 ↗
26. Microstructural and properties investigations of tantalum-doped tungsten diboride ceramic coatings via HiPIMS and RF magnetron sputtering10.1007/s43452-024-01050-0 ↗
27. Nanosecond transient thermoreflectance method for characterizing anisotropic thermal conductivity10.1063/1.5099961 ↗
28. Thermal conductivity of layered borides: the effect of building defects on the thermal conductivity of TmAlB4 and the anisotropic thermal conductivity of AlB210.1063/1.4871797 ↗
29. Some physical properties of the higher borides of molybdenum and tungsten10.1016/0022-5088(79)90012-2 ↗
30. Elastic anisotropies and thermal conductivities of WB2 diborides in different crystal structures: a first-principles calculation10.1016/j.jallcom.2018.03.109 ↗
31. Sorting transition-metal diborides: new descriptor for mechanical properties10.1016/j.actamat.2021.116685 ↗
32. Large mechanical properties enhancement in ceramics through vacancy-mediated unit cell disturbance10.1038/s41467-023-44060-x ↗
33. H. Riedl, Anisotropic super-hardness of hexagonal WB2±z thin films10.1080/21663831.2021.2021308 ↗
34. Inhomogeneous electron gas10.1103/PhysRev.136.B864 ↗
35. Self-consistent equations including exchange and correlation effects10.1103/PhysRev.140.A1133 ↗
36. Metric tensor formulation of strain in density-functional perturbation theory10.1103/PhysRevB.71.035117 ↗
37. The ABINIT project: impact, environment and recent developments10.1016/j.cpc.2019.107042 ↗
38. Accurate and simple analytic representation of the electron-gas correlation energy10.1103/PhysRevB.45.13244 ↗
39. Generation of projector augmented-wave atomic data: A 71 element validated table in the XML format10.1016/j.cpc.2013.12.023 ↗
40. Elastic and electronic properties of XB2 (X=V, Nb, Ta, Cr, Mo, and W) with AlB2 structure from first principles calculations10.1016/j.ceramint.2013.11.026 ↗
41. Structural, mechanical, optical, thermodynamical and phonon properties of stable ReB2 polymorphs from density functional calculations10.1016/j.jallcom.2015.10.133 ↗
42. The elastic behaviour of a crystalline aggregate10.1088/0370-1298/65/5/307 ↗
43. Estimation of isotropic hyperelasticity constitutive models to approximate the atomistic simulation data for aluminium and tungsten monocrystals
44. Lattice instabilities in metallic elements10.1103/RevModPhys.84.945 ↗
45. Mechanical stability conditions for 3D and 2D crystals under arbitrary load
46. Application of machine learning methods for predicting new superhard materials10.1063/5.0012055 ↗
47. XCII. Relations between the elastic moduli and the plastic properties of polycrystalline pure metals10.1080/14786440808520496 ↗
48. Flexible hard nanocomposite coatings10.1039/C5RA09586G ↗
49. Materials selection guidelines for low thermal conductivity thermal barrier coatings10.1016/S0257-8972(02)00593-5 ↗
50. Lower limit to the thermal conductivity of disordered crystals10.1103/PhysRevB.46.6131 ↗
51. Mechanical and thermal properties of W-Ta-B coatings deposited by high-power impulse magnetron sputtering (HiPIMS)10.3390/ma16020664 ↗
52. Properties of spark plasma sintered compacts and magnetron sputtered coatings made from Cr, Mo, Re and Zr alloyed tungsten diboride10.3390/coatings11111378 ↗
53. Gwyddion: an open-source software for SPM data analysis10.2478/s11534-011-0096-2 ↗
54. Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology10.1557/jmr.2004.19.1.3 ↗
55. Elastic/plastic indentation damage in ceramics: the median/radial crack system10.1111/j.1151-2916.1980.tb10768.x ↗
56. Thermal diffusivity measurement in a diamond anvil cell using a light pulse thermoreflectance technique10.1088/0957-0233/22/2/024011 ↗
57. Fourier transform thermoreflectance method under front-heat front-detect configuration10.1007/s10765-024-03351-1 ↗
58. Structure function analysis of temperature-dependent thermal properties of nm-thin Nb2O510.3390/en12040610 ↗
59. Heat capacity and enthalpy of transition-metal borides in a broad range of temperatures 30(12)10.1007/BF00794439 ↗
60. Effects of vacancies on the mechanical properties of zirconium: an ab initio investigation10.1016/j.matdes.2017.01.060 ↗
61. New zirconium diboride polymorphs - first-principles calculations10.3390/ma13133022 ↗
62. Fundamental structure forming phenomena of polycrystalline films and the structure zone models10.1016/S0040-6090(97)00503-8 ↗
63. Williams · 2009
64. Paradigm shift in thin-film growth by magnetron sputtering: From gas-ion to metal-ion irradiation of the growing film10.1116/1.5121226 ↗
65. A position-space view on chemical bonding in metal diborides with AlB2 type of crystal structure10.1002/zaac.201200523 ↗
66. Elastic properties, fracture toughness, ideal tensile strength and thermal conductivities of the stable hexagonal WB2, W2B5, WB3, and WB410.1007/s00339-022-05299-1 ↗
67. Thermal conductivity of layered borides: the effect of building defects on the thermal conductivity of TmAlB4 and the anisotropic thermal conductivity of AlB210.1063/1.4871797 ↗
68. Self-organized nanocolumnar structure in superhard TiB2 thin films10.1063/1.1887824 ↗
69. Electronic and lattice distortions induce elastic softening in refractory multicomponent borides10.1021/acs.chemmater.3c01086 ↗
70. Theoretical predictions of structure and related properties of intermetallics10.1179/mst.1992.8.4.345 ↗