journal article·2025-10Open access

Effect of the cooling rate on mechanical properties and microstructure of a co-precipitated Fe/Cu prealloyed powder

C. Luno-Bilbao, N. Vielma, A. Iza, G. Peña, I. Iturriza

Abstract

This work investigates the influence of sintering temperature and cooling rate on the microstructural evolution and mechanical performance of a commercial Fe–Cu–Sn-based prealloyed powder (Cobalite CNF®) processed by conventional pressureless sintering. Two sintering temperatures (900 °C and 980 °C) and two cooling rates (10 °C/min and 45 °C/min) were selected to evaluate their effects on densification, precipitation behaviour, and mechanical response. A combination of scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron diffraction was used to characterize the resulting microstructures. This study was essential to describe the precipitation phenomenon of copper in the iron rich phase during the cooling from the sintering temperature. The results demonstrate that fast cooling promotes a higher density of finer Cu precipitates within the ferritic matrix, which significantly enhances hardness and yield strength. In contrast, slow cooling favours precipitate coarsening via Ostwald ripening, leading to a decrease in mechanical properties. At 980 °C, the γ → α transformation induced interphase precipitation, forming aligned rows of Cu-rich particles, while at 900 °C precipitation occurred mainly from supersaturated ferrite. The highest mechanical performance (720 MPa UTS, 610 MPa yield strength, 100 HRB) was obtained for the specimens sintered at 980 °C and fast cooled, confirming the critical role of thermal treatment in tailoring the microstructure and optimizing the final properties of CNF-based alloys for demanding applications such as diamond tool matrices. • The effect of sintering temperature and cooling rate on the microstructure and mechanical properties of Cobalite CNF® (Fe–Cu–Sn-based prealloyed powder) was systematically investigated. • Fast cooling (45 °C/min) after sintering promotes the formation of fine, uniformly distributed Cu precipitates, significantly enhancing hardness (100 HRB) and yield strength (610 MPa). • Slow cooling (10 °C/min) leads to precipitate coarsening via Ostwald ripening, resulting in reduced mechanical performance. • At 980 °C, the γ → α transformation induces interphase precipitation, forming aligned rows of Cu-rich particles, a mechanism absent at 900 °C. • Despite the intended oxide dispersion strengthening (ODS) via Y₂O₃ particles, coarsening during sintering limits their effectiveness; however, their hardness contributes to wear resistance. • The Orowan strengthening mechanism was confirmed through TEM and statistical modelling, with finer precipitates acting as effective barriers to dislocation motion. • The optimised sintering condition (980 °C, fast cooling) yields mechanical properties suitable for diamond tool matrices and structural applications, offering a cost-effective alternative to cobalt-based systems.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. About the relationship of the processing conditions, mechanical properties, and microstructure of a co-precipitated Fe/Cu prealloyed powder10.1016/j.heliyon.2023.e13931 ↗
2. Copper precipitation behavior during continuous cooling and subsequent aging of powder-forged Fe-2.5Cu-C alloy10.3390/met10101350 ↗
3. Phase field study of the copper precipitation in Fe-Cu alloy10.1016/j.actamat.2019.01.009 ↗
4. Effect of Y2O3 nanoparticles on enhancing microstructure and mechanical properties of oxide dispersion strengthened w alloy10.1016/j.ijrmhm.2023.106534 ↗
5. ASTM E8/E8M standard test methods for tension testing of metallic materials 1
6. Thermodynamic analysis of the stable and metastable Co-Cu and Co-Cu-Fe phase diagrams10.1016/j.calphad.2005.10.007 ↗
7. Effect of Cu-15Sn on the microstructure and mechanical properties of pressureless sintered Fe-Co-Cu alloy
8. Luno-Bilbao · 2012
9. A novel dissolution-precipitation mechanism during liquid phase sintering and its strengthening effects in W-Ni-Fe alloys with low w contents10.1016/j.matdes.2022.110841 ↗
10. Development of Y2 O3 Dispersion-Strengthened copper alloy by Sol-Gel method10.3390/ma15072416 ↗
11. Grain coarsening kinetics and strength modeling of Fe–15Cr–2W oxide dispersion strengthened steels with varying yttria contents10.1007/s11106-024-00437-1 ↗
12. Investigation of the crystallographic evolution sequence of Nano-Precipitation via HRTEM in Cu-Bearing Ultra-Low carbon steel
13. Cu precipitation behaviors and microscopic mechanical characteristics of a novel ultra-low carbon steel
14. In situ EBSD analysis on the crystal orientation relationship between ferrite and austenite during reverse transformation of an Fe-Mn-C alloy10.2320/matertrans.MAW201602 ↗
15. Demange G., Lavrskyi M., Chen K., Chen X., Wang Z.D., Patte R., et al. Fcc -> bcc Phase Transition Kinetics In An Immiscible Binary System: Atomistic Evidence Of The Twinning Mechanism Of Transformation 2021.10.2139/ssrn.3820197 ↗
16. Effect of build orientation and heat treatment on the microstructure, mechanical and corrosion performance of super duplex stainless steels fabricated via laser powder bed fusion10.1039/D4MA00448E ↗
17. A systematical evaluation of the crystallographic orientation relationship between MC precipitates and ferrite matrix in HSLA steels
18. A metallographic study of precipitation of copper from alpha iron
19. RH; YY. Precipitation behavior of an Fe-1.03 wt% cu alloy
20. Cu precipitation dynamics in an Fe-1.18%Cu alloy
21. Revisiting the precipitation mechanisms of Guinier-Preston zones, η′, and η precipitates in Al-Zn-Mg alloys10.1016/j.actamat.2024.119789 ↗
22. Microstructure evolution during thermal aging of Fe-Cu alloys
23. Peculiarities of copper precipitation in hypereutectoid
24. Comparative study of VC, NbC, and TiC interphase precipitation in microalloyed Low-carbon steels10.1007/s11661-020-06001-x ↗
25. On the correlation among continuous cooling transformations, interphase precipitation and strengthening mechanism in Ti-microalloyed steel10.1016/j.jmrt.2020.12.048 ↗
26. Influence of Solute Drag Effect And Interphase Precipitation Of Nb On Ferrite Transformation10.3390/ma17102440 ↗
27. A new model of interphase precipitation in copper-containing steels10.1023/A:1006623915506 ↗
28. Complex precipitation behavior and mechanism of NbC during ferrite transformation in a HSLA steel10.1007/s11661-024-07515-4 ↗
29. Statistical modeling of the orowan bypass mechanism for randomly distributed obstacles10.1007/s11661-023-06990-5 ↗
30. Ashby M.F. Materials Selection, Second Edititon 1999.
31. 2 dislocation meets hard undeformable second phase particles: dislocation release at higher stresses May occur by orowan looping or by cross-slip10.1179/026708399773002782 ↗
32. Influence of thermo-mechanical processing and different post-cooling techniques on structure and properties of an ultra low carbon cu bearing HSLA forging10.1016/S0921-5093(02)00735-9 ↗