Microstructural refinement and strength-ductility optimization in Ti-15Zr alloys via cobalt microalloying
Source abstract
Abstract
This study examines the influence of minor cobalt (Co) additions on the microstructural evolution and mechanical properties of Ti-15Zr alloys subjected to thermomechanical processing. Alloys containing up to 2 wt% Co were prepared via plasma arc melting, followed by homogenization, hot rolling, and cold rolling. Microstructural observations using optical microscopy and SEM showed that Co addition refined the prior β grain structure and promoted equiaxed α-phase formation. This refinement is attributed to solute drag during solidification, driven by Co’s high growth restriction factor (Q-value), which suppressed grain coarsening and enhanced dynamic recrystallization. Tensile testing revealed that strength increased with Co content, while ductility was preserved up to 1 wt% Co. The 1Co alloy exhibited the best strength-ductility balance in both hot- and cold-rolled states. In contrast, the 2Co alloy, although stronger, exhibited reduced elongation due to grain boundary instability, and limited strain hardening. EBSD analysis confirmed that the 1Co alloy developed a refined and isotropic α-phase structure, a weakened and broadened basal texture along the transverse direction, and favorable conditions for prismatic slip activation. These features were supported by uniform KAM distributions, indicating enhanced slip compatibility and reduced intragranular strain localization. TEM analysis further revealed uniform dislocation structures and effective dynamic recovery in the 1Co alloy, whereas the 2Co alloy exhibited dense dislocation tangles and planar strain bands, consistent with severe strain localization. Quantitative strengthening analysis showed that dislocation hardening was the dominant mechanism, while grain refinement and solid-solution strengthening provided only minor contributions to the overall strength increase. These findings demonstrate that 1 wt% Co is an optimal microalloying level for enhancing both strength and ductility in Ti-15Zr alloys, providing a practical design strategy for advanced biomedical and structural titanium applications.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Microstructure and mechanical properties · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. The effect of the solute on the structure, selected mechanical properties, and biocompatibility of Ti–Zr system alloys for dental applications10.1016/j.msec.2013.09.032 ↗
2. Ti based biomaterials, the ultimate choice for orthopaedic implants–A review10.1016/j.pmatsci.2008.06.004 ↗
3. Improved biocompatibility of titanium–zirconium (Ti–Zr) alloy: tissue reaction and sensitization to Ti–Zr alloy compared with pure ti and zr in rat implantation study10.2320/matertrans.46.2260 ↗
4. Elastic properties of as-solidified Ti-Zr binary alloys for biomedical applications10.2320/matertrans.MI201501 ↗
5. Influence of nb addition on microstructural evolution and compression mechanical properties of Ti-Zr alloys10.1016/j.jmst.2020.03.092 ↗
6. Preliminary study of microstructure, mechanical properties and corrosion resistance of antibacterial Ti-15Zr-xCu alloy for dental application10.1016/j.jmst.2020.03.003 ↗
7. A promising of alloying modified beta-type Titanium-Niobium implant for biomedical applications: microstructural characteristics, in vitro biocompatibility and antibacterial performance10.1016/j.jallcom.2016.12.120 ↗
8. A double-blind randomized controlled trial (rct) of titanium-13zirconium versus titanium grade iv small-diameter bone level implants in edentulous mandibles–results from a 1-year observation period10.1111/j.1708-8208.2010.00324.x ↗
9. Electrochemical study and mechanical properties of Ti-Zr alloy for biomedical applications10.3390/cryst14060493 ↗
10. Is titanium–zirconium alloy a better alternative to pure titanium for oral implant? Composition, mechanical properties, and microstructure analysis10.1016/j.sdentj.2020.08.009 ↗
11. Fatigue behavior of Ti50Zr alloy for dental implant application10.1016/j.jallcom.2019.04.165 ↗
12. On the mechanical biocompatibility of Ti-15Zr-based alloys for potential use as load-bearing implants10.1016/j.jmrt.2019.11.051 ↗
13. Modes and processes of severe plastic deformation (SPD)10.3390/ma11071175 ↗
14. Severe plastic deformation (SPD) processes for metals10.1016/j.cirp.2008.09.005 ↗
15. Evolution of microstructure and mechanical properties of Ti-Nb-Zr and Ti-Nb-Zr-Ta-Sn alloys in severe plastic deformation10.1016/j.matlet.2024.137805 ↗
16. Principles of equal-channel angular pressing as a processing tool for grain refinement10.1016/j.pmatsci.2006.02.003 ↗
17. Effect of multi-pass equal channel angular pressing on the microstructure and mechanical properties of a heterogeneous Mg88Y8Zn4 alloy10.1016/j.jmst.2016.05.015 ↗
18. Microstructure development during equal-channel angular pressing of titanium10.1016/S1359-6454(02)00501-3 ↗
19. The effect of equal-channel angular pressing on the structure and mechanical behavior of Ti–6Al–4V alloy10.1016/j.msea.2004.02.093 ↗
20. Processing pure ti by high-pressure torsion in wide ranges of pressures and strain10.1007/s11661-009-9890-5 ↗
21. Enhancement in mechanical properties of a β-titanium alloy by high-pressure torsion10.1016/j.jmrt.2014.10.010 ↗
22. Phase transformation and mechanical properties of nanocrystalline Ti–2Fe-0.1 b alloy processed by high pressure torsion10.1016/j.jmrt.2024.06.164 ↗
23. Influence of fe addition in CP titanium on phase transformation, microstructure and mechanical properties during high pressure torsion10.1016/j.jallcom.2019.153604 ↗
24. The influence of rapid-diffusive β-stabilizers on the microstructure formation and superplasticity of titanium-based alloys10.1016/j.jallcom.2024.175065 ↗
25. Effects of co on the microstructure evolution and mechanical properties of Ti-4Al-6Cr-5Mo-8 nb alloy by ultrasonic vacuum melting10.1016/j.jallcom.2024.174412 ↗
26. Columnar to equiaxed transition in additively manufactured titanium alloys: a comprehensive review of mechanisms and grain control strategies
27. Research progress on slip behavior of α-Ti under quasi-static loading: a review10.3390/met12101571 ↗
28. Structural and mechanical properties of Ti–Co alloys treated by high pressure torsion10.3390/ma12030426 ↗
29. Rapid solidification of intermetallic compounds10.1179/imr.1988.33.1.201 ↗
30. Beryllium as a grain refiner in titanium alloys10.1016/j.jallcom.2009.03.016 ↗
31. The contribution of constitutional supercooling to nucleation and grain formation10.1007/s11661-015-2960-y ↗
32. Correlation between alpha phase morphology and tensile properties of a new beta titanium alloy10.1016/j.matdes.2017.02.043 ↗
33. Beta to alpha transformation kinetics and microstructure of Ti-6Al-4V alloy during continuous cooling10.1016/j.matchemphys.2016.06.082 ↗
34. An in situ study of microstructural strain localization and damage evolution in an (α+ β) Ti-Al-V-Fe-Si-O alloy10.1016/j.actamat.2022.118424 ↗
35. Texture evolution of α-Ti and β-Ti alloys during rolling and recrystallization10.1002/adem.202400876 ↗
36. A study of active deformation systems in titanium alloys: dependence on alloy composition and correlation with deformation texture10.1016/S0921-5093(02)00421-5 ↗
37. Non-basal slip systems in HCP metals and alloys: source mechanisms10.1016/S0921-5093(01)01027-9 ↗
38. The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys10.1016/S1359-6454(03)00005-3 ↗
39. Effect of texture and slip mode on the anisotropy of plastic flow and flow softening during hot working of Ti-6Al-4V10.1007/s11661-001-0155-1 ↗
40. Understanding the deformation behaviours of mg alloys with dispersed non-basal grain-embedded orientation heterostructures10.1016/j.actamat.2024.119727 ↗
41. Investigation of the indentation size effect through the measurement of the geometrically necessary dislocations beneath small indents of different depths using EBSD tomography10.1016/j.actamat.2008.09.039 ↗
42. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
43. Stress localization resulting from grain boundary dislocation interactions in relaxed and defective grain boundaries10.1007/s11661-019-05534-0 ↗
44. A high-strength and high-ductility Zn–Ag alloy achieved through trace mg addition and ECAP10.1016/j.msea.2023.145381 ↗
45. Control of the lamellar structure and analysis of tensile properties of TiC/Ti-6Al-3Sn-9Zr-1.5 mo composite produced by in situ casting technique10.3390/met11010160 ↗
46. Effect of α-platelet thickness on the mechanical properties of Ti-6Al-4V alloy with lamellar microstructure
47. Modelling strengthening mechanisms in beta-type ti alloys10.1016/j.msea.2019.04.027 ↗