journal article·2025-03Open access

Interface and microstructure of heterogeneous laminated steels upon shear loading

Yanke Liu, Wei Wang, Muxin Yang, Sihai Jiao, Lingling Zhou, Jing Wang, Xiaolei Wu, Fuping Yuan

Abstract

The effects of interface spacing, austenite stability and recrystallization degree on the dynamic shear behaviors of heterogeneous laminated steels have been studied, and the corresponding dynamic deformation mechanisms have been revealed. The 6 and 18-layered laminated structures consist of a 304 L stainless steel as surface layers, and a low C steel and a medium-Mn steel as alternating center layers. The dynamic shear properties can be slightly enhanced with reduced interface spacing and significantly improved through a two-step heat-treated process. Superior synergy of dynamic shear strength and dynamic shear toughness can be achieved in the heterogeneous laminated steels, as compared to stainless steels and low alloy steels, including the base materials of 304 L stainless steel and low C steel. The austenite stability can be improved through a two-step heat treatment, leading to a relatively higher Mn enrichment in austenite compared to a one-step heat treated process. This increased austenite stability can elevate the stress or strain threshold for martensitic transformation, thereby postponing the martensite transformation to a larger shear strain range, i.e. from approximately 1.35 for the one-step heat-treated sample to approximately 2.45 for the two-step heat-treated sample. The higher temperature heating is employed in the two-step heat-treated process, enabling full recrystallization and thereby restoring the hardening capacity of the surface layers. Consequently, the combination of these two factors leads to significantly improved dynamic shear strain and toughness. • The coupling effects of austenite stability and recrystallization degree on the impact behaviors. • Smaller interface spacing induces slightly higher shear strain and toughness under dynamic loading. • Improving austenite stability enhances dynamic shear strain and toughness. • The restoration of the deformation capacity of surface layers improves dynamic shear strain and toughness.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Material Properties and Failure Mechanisms · Microstructure and Mechanical Properties of Steels · Material Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Impact energy absorption capability of magnesium alloy pipe10.2320/jinstmet.JBW201308 ↗
2. Compressive properties and energy absorption characteristics of extruded Mg-Al-Ca-Mn alloy at various high strain rates
3. Excellent dynamic properties and corresponding deformation mechanisms in a microband-induced plasticity steel with dual-heterogeneous structure10.1016/j.jmrt.2023.11.007 ↗
4. Superior dynamic shear properties by structures with dual gradients in medium entropy alloys10.1016/j.jmst.2023.01.014 ↗
5. Gradient structure produces superior dynamic shear properties10.1080/21663831.2017.1334715 ↗
6. High-velocity deformation of Al0.3CoCrFeNi high-entropy alloy: Remarkable resistance to shear failure
7. The use of hat-shaped specimens to study the high strain rate shear behaviour of Ti-6Al-4V10.1016/j.ijimpeng.2009.08.002 ↗
8. Nanostructuring of metals by severe plastic deformation for advanced properties10.1038/nmat1180 ↗
9. Nanostructured metals - retaining ductility10.1038/nmat1141 ↗
10. Superior mechanical properties and deformation mechanisms of heterogeneous laminates under dynamic shear loading10.1016/j.msea.2019.04.082 ↗
11. Towards strength-ductility synergy through the design of heterogeneous nanostructures in metals10.1016/j.mattod.2017.02.003 ↗
12. Dynamic shear behaviors and microstructural deformation mechanisms in FeNiAlC dual-phase high strength alloy
13. Dynamic shear deformation of a CrCoNi medium-entropy alloy with heterogeneous grain structures10.1016/j.actamat.2018.02.016 ↗
14. Additively-manufactured functionally graded Ti-6Al-4V lattice structures with high strength under static and dynamic loading: experiments10.1016/j.ijimpeng.2017.09.018 ↗
15. Dynamic shear characteristics of titanium alloy Ti-6Al-4V at large strain rates by the split Hopkinson pressure bar test10.1016/j.ijimpeng.2017.06.007 ↗
16. Heterostructured materials10.1016/j.pmatsci.2022.101019 ↗
17. Heterostructured materials: superior properties from hetero-zone interaction10.1080/21663831.2020.1796836 ↗
18. Heterogeneous materials: a new class of materials with unprecedented mechanical properties10.1080/21663831.2017.1343208 ↗
19. Mechanical properties of copper/bronze laminates: role of interfaces10.1016/j.actamat.2016.06.023 ↗
20. Interface affected zone for optimal strength and ductility in heterogeneous laminate10.1016/j.mattod.2018.03.006 ↗
21. Improving ductility by increasing fraction of interfacial zone in low C steel/304 SS laminates10.1016/j.msea.2018.04.102 ↗
22. Stress partitioning behavior of multilayered steels during tensile deformation measured by in situ neutron diffraction10.1016/j.scriptamat.2011.10.018 ↗
23. Length-scale-dependent deformation mechanisms in incoherent metallic multilayered composites10.1016/j.actamat.2005.06.025 ↗
24. Enhanced strength in pure Ti via design of alternating coarse- and fine-grain layers10.1016/j.actamat.2021.116627 ↗
25. High-strength and thermally stable bulk nanolayered composites due to twin-induced interfaces10.1038/ncomms2651 ↗
26. Strain hardening and ductility in a coarse-grain/nanostructure laminate material10.1016/j.scriptamat.2015.03.006 ↗
27. Homogenization of plastic deformation in heterogeneous lamella structures10.1080/21663831.2016.1255264 ↗
28. Effects of layer thickness on deformation-induced martensite transformation and tensile behaviors in a multilayer laminate10.1016/j.jmrt.2023.07.006 ↗
29. Adiabatic shear banding in ultrafine-grained Fe processed by severe plastic deformation10.1016/j.actamat.2003.12.025 ↗
30. High-strain-rate response of ultra-fine-grained copper10.1016/j.actamat.2008.02.023 ↗
31. Amorphization in extreme deformation of the CrMnFeCoNi high-entropy alloy10.1126/sciadv.abb3108 ↗
32. Dynamic shear response and evolution mechanisms of adiabatic shear band in an ultrafine-grained austenite-ferrite duplex steel10.1016/j.mechmat.2015.06.004 ↗
33. Annealing effect on the evolution of adiabatic shear band under dynamic shear loading in ultra-fine-grained iron10.1016/j.ijimpeng.2012.07.001 ↗
34. Influence of shock prestraining on the formation of shear localization in 304 stainless steel10.1007/s11661-005-0239-4 ↗
35. Kolsky · 1963
36. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
37. Characterization of microstructure formation and mechanical behavior of an advanced medium Mn steel
38. Physical metallurgy of medium-Mn advanced high-strength steels10.1080/09506608.2022.2153220 ↗
39. The effects of the initial martensite microstructure on the microstructure and tensile properties of intercritically annealed Fe-9Mn-0.05C steel10.1016/j.actamat.2014.07.005 ↗
40. The effects of the heating rate on the reverse transformation mechanism and the phase stability of reverted austenite in medium Mn steels10.1016/j.actamat.2013.12.038 ↗
41. Experimental and numerical analysis on formation of stable austenite during the intercritical annealing of 5Mn steel10.1016/j.actamat.2011.03.025 ↗
42. A novel technique for dynamic shear testing of bulk metals with application to 304 austenitic stainless steel10.1016/j.ijsolstr.2020.08.019 ↗
43. Enhanced quasi-static and dynamic shear properties by heterogeneous gradient and lamella structures in 301 stainless steels10.1016/j.msea.2016.10.111 ↗
44. Dynamic mechanical behavior and microstructural evolution of additively manufactured 316L stainless steel10.1007/s10853-021-06765-6 ↗
45. V. Pushkov, A. Yurlov, A. Bol'shakov, A. Podurets, A. Kal'manov, E. Koshatova, Study of adiabatic localized shear in metals by split Hopkinson pressure bar method, Conference on New Models and Hydrocodes for Shock Wave Processes in Condensed Matter, E D P Sciences, Paris, FRANCE, 2010.10.1051/epjconf/20101000029 ↗
46. Mechanical behavior and microstructural development of low-carbon steel and microcomposite steel reinforcement bars deformed under quasi-static and dynamic shear loading10.1007/s11661-009-9869-2 ↗
47. A novel design to eliminate Luders band in medium-Mn steel and its microstructure-property relationship10.3390/cryst13060936 ↗
48. Deformation mechanisms for a new medium-Mn steel with 1.1 GPa yield strength and 50% uniform elongation10.1016/j.jmst.2022.05.048 ↗
49. Extra strengthening in a coarse/ultrafine grained laminate: role of gradient interfaces10.1016/j.ijplas.2019.07.019 ↗