journal article·2023-12Open access

Managing the inevitable microstructural and property heterogeneity in powder bed fusion Ti-6Al-4V parts via heat treatment

Yuhui Tu, Seán B. Leen, Noel M. Harrison

Abstract

This study investigates the effects of the commonly-observed microstructure heterogeneity from the metal electron beam powder bed fusion (PBF-EB) processes and how it evolves following the associated heat treatment (HT), on the tensile behaviour of Ti-6Al-4V alloy. A strain gradient crystal plasticity finite element (CPFE) method is employed using physically-based dislocation mechanics to capture the microstructure-sensitive size effect. Microstructural characterization is performed using electron backscatter diffraction (EBSD) of the as-built and post-HT specimens, with measurements of grain morphology, phase, and texture extracted from the bottom and top regions of specimens, used to construct the CPFE models. The dual-phase CPFE model represents α (hcp) and β (bcc) basket-weave morphology, typical in Ti-6Al-4V, with accurate PBF-induced texture definitions defined directly from the measured EBSD data. Key microstructural features exhibiting a gradient include lath width and phase fraction. The effects of as-built microstructural gradient in a single component include an increase of lath width by 43 %, and the beta phase fraction, from bottom to top. The CPFE models successfully predict the effect of HT and microstructural gradient on tensile response, specifically yield stress and initial hardening rate. The role of dislocation density and the associated influence of lath width on yield stress are empirically correlated for the structure-property design of PBF-EB metals. This study also demonstrates the homogenising effect of the heat treatment; effectively eradicating the microstructural gradient observed in as-built specimens. • Heterogenous structure-property relationship is observed in powder bed fusion built Ti-6Al-4V alloys. • As-built gradient is the lath width and beta phase fractions increasing, tensile strength decreasing in the build direction. • Post-built heat treatment is necessary to homogenise the printed part, leading to a 10 % reduction in yield strength. • A strain gradient crystal plasticity model with dislocation density for dual-phase Ti-6Al-4V microstructural deformation. • Quantitative fitting Ti-6Al-4V lath size and the crystal plasticity predictions concluded 3 structure-property relationships.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Titanium Alloys Microstructure and Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (71)

Show source-provided references
1. Anisotropy and heterogeneity of microstructure and mechanical properties in metal additive manufacturing: A critical review10.1016/j.matdes.2017.11.021 ↗
2. Additive manufacturing in construction: A review on processes, applications, and digital planning methods
3. On microstructural homogenization and mechanical properties optimization of biomedical Co-Cr-Mo alloy additively manufactured by using electron beam melting
4. Additive manufacturing of metallic components–process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
5. Microstructure and Mechanical Properties of Long Ti-6Al-4V Rods Additively Manufactured by Selective Electron Beam Melting Out of a Deep Powder Bed and the Effect of Subsequent Hot Isostatic Pressing10.1007/s11661-015-2976-3 ↗
6. Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties10.1016/j.jallcom.2012.07.022 ↗
7. Material Properties of Ti6Al4V Parts Produced by Laser Metal Deposition10.1016/j.phpro.2012.10.056 ↗
8. Phase transformations during cooling in α+β titanium alloys10.1016/S0921-5093(97)00802-2 ↗
9. Additive manufacturing of strong and ductile Ti–6Al–4V by selective laser melting via in situ martensite decomposition10.1016/j.actamat.2014.11.028 ↗
10. A critical evaluation of the microstructural gradient along the build direction in electron beam melted Ti-6Al-4V alloy10.1016/j.msea.2018.12.016 ↗
11. Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting10.1016/j.actamat.2015.06.036 ↗
12. Assessment of intra-build variations in tensile strength in electron beam powder-bed fusion Ti–6AL–4V part 1: Effects of build height10.1016/j.msea.2022.143354 ↗
13. Effect of hot isostatic pressing (HIP) on microstructure and mechanical properties of Ti6Al4V alloy fabricated by cold spray additive manufacturing
14. Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment10.1016/j.jallcom.2021.162648 ↗
15. Fracture and fatigue in additively manufactured metals10.1016/j.actamat.2021.117240 ↗
16. A review on the fatigue behavior of Ti-6Al-4V fabricated by electron beam melting additive manufacturing10.1016/j.ijfatigue.2018.09.022 ↗
17. Ti-6Al-4V powder characteristics in laser powder bed fusion: The effect on tensile and fatigue behavior
18. Heat-treatment effects on mechanical properties and microstructure evolution of Ti-6Al-4V alloy fabricated by laser powder bed fusion
19. Additive manufacturing of Ti–6Al–4V parts through laser metal deposition (LMD): Process, microstructure, and mechanical properties10.1016/j.jallcom.2019.04.255 ↗
20. Steels in additive manufacturing: A review of their microstructure and properties10.1016/j.msea.2019.138633 ↗
21. Heterogeneous linear elastic trabecular bone modelling using micro-CT attenuation data and experimentally measured heterogeneous tissue properties10.1016/j.jbiomech.2008.05.014 ↗
22. Overview of constitutive laws, kinematics, homogenization and multiscale methods in crystal plasticity finite-element modeling: Theory, experiments, applications10.1016/j.actamat.2009.10.058 ↗
23. Towards an instant structure-property prediction quality control tool for additive manufactured steel using a crystal plasticity trained deep learning surrogate10.1016/j.matdes.2021.110345 ↗
24. Lath Martensite Microstructure Modeling: A High-Resolution Crystal Plasticity Simulation Study10.3390/ma14030691 ↗
25. Optimal polyhedral description of 3D polycrystals: Method and application to statistical and synchrotron X-ray diffraction data10.1016/j.cma.2017.10.029 ↗
26. Crystal plasticity analysis of deformation anisotropy of lamellar TiAl alloy: 3D microstructure-based modelling and in-situ micro-compression10.1016/j.ijplas.2019.04.012 ↗
27. Microstructure-based crystal plasticity modeling of cyclic deformation of Ti–6Al–4V10.1016/j.ijplas.2006.11.009 ↗
28. Research on the hot tensile deformation mechanism of Ti-6Al-4 V alloy sheet based on the α + β dual phase crystal plasticity modeling10.1016/j.jallcom.2022.167701 ↗
29. Tensile properties of Ti-6Al-4V as-built by laser metal deposition: The relationship between heat affected zone bands, strain localization and anisotropy in ductility
30. Lengthscale-dependent, elastically anisotropic, physically-based hcp crystal plasticity: Application to cold-dwell fatigue in Ti alloys10.1016/j.ijplas.2006.10.013 ↗
31. A high-fidelity crystal-plasticity finite element methodology for low-cycle fatigue using automatic electron backscatter diffraction scan conversion: Application to hot-rolled cobalt–chromium alloy
32. Strain-gradient modelling of grain size effects on fatigue of CoCr alloy10.1016/j.actamat.2014.06.044 ↗
33. An analysis of the influence of grain size on the strength of FCC polycrystals by means of computational homogenization10.1016/j.actamat.2018.01.024 ↗
34. A strain-gradient, crystal plasticity model for microstructure-sensitive fretting crack initiation in ferritic-pearlitic steel for flexible marine risers10.1016/j.ijfatigue.2018.01.028 ↗
35. Crystal plasticity analysis of micro-deformation, lattice rotation and geometrically necessary dislocation density10.1098/rspa.2012.0050 ↗
36. PhD Thesis: Micromechanical modelling of size effects in crack initiation with application to fretting fatigue and cold dwell fatigue
37. Determination of Ti-6242 α and β slip properties using micro-pillar test and computational crystal plasticity10.1016/j.jmps.2016.06.007 ↗
38. Integrated experimental–simulation analysis of stress and strain partitioning in multiphase alloys10.1016/j.actamat.2014.07.071 ↗
39. Functionally graded bimodal Ti6Al4V fabricated by powder bed fusion additive manufacturing: Crystal plasticity finite element modelling10.1016/j.msea.2019.138736 ↗
40. Ti–6Al–4V microstructural functionally graded material by additive manufacturing: Experiment and computational modelling10.1016/j.msea.2021.141782 ↗
41. Crystal plasticity simulation of the effect of grain size on the fatigue behavior of polycrystalline Inconel 71810.1016/j.ijfatigue.2018.04.018 ↗
42. Texture Analysis with MTEX – Free and Open Source Software Toolbox10.4028/www.scientific.net/SSP.160.63 ↗
43. Denoising of crystal orientation maps10.1107/S1600576719009075 ↗
44. A Comparison of Statistically Equivalent and Realistic Microstructural Representative Volume Elements for Crystal Plasticity Models10.1007/s40192-022-00257-4 ↗
45. Elastic properties of reinforced solids: Some theoretical principles10.1016/0022-5096(63)90036-X ↗
46. The Influence of Mechanical Constraints Introduced by β Annealed Microstructures on the Yield Strength and Ductility of Ti-6Al-4V10.1016/j.jmps.2017.03.013 ↗
47. Kiwanuka · 2013
48. The deformation of plastically non-homogeneous materials10.1080/14786437008238426 ↗
49. GND accumulation in bi-crystal deformation: Crystal plasticity analysis and comparison with experiments10.1016/j.ijmecsci.2009.03.005 ↗
50. Thermodynamic analysis of dislocation glide controlled by dispersed local obstacles10.1016/0025-5416(69)90026-3 ↗
51. Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density10.1016/S1359-6454(99)00020-8 ↗
52. The mechanism of plastic deformation of crystals
53. High– and low–cycle fatigue crack initiation using polycrystal plasticity10.1098/rspa.2003.1258 ↗
54. Incorporating grain-level residual stresses and validating a crystal plasticity model of a two-phase Ti-6Al-4 V alloy produced via additive manufacturing10.1016/j.jmps.2018.07.025 ↗
55. The effect of the beta phase on the micromechanical response of dual-phase titanium alloys10.1016/j.ijfatigue.2017.03.020 ↗
56. 2018
57. Fatigue damage characterisation of MarBN steel for high temperature flexible operating conditions
58. Zhan · 2004
59. Effects of laser power on geometry, microstructure and mechanical properties of printed Ti-6Al-4V parts10.1016/j.jmatprotec.2019.116539 ↗
60. Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density10.1016/S1359-6454(99)00020-8 ↗
61. Resolving the geometrically necessary dislocation content by conventional electron backscattering diffraction10.1016/j.scriptamat.2008.01.050 ↗
62. Twinning and sequential kinking in lamellar Ti-6Al-4V alloy10.1016/j.actamat.2019.10.010 ↗
63. A study of active deformation systems in titanium alloys: dependence on alloy composition and correlation with deformation texture10.1016/S0921-5093(02)00421-5 ↗
64. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
65. The cleavage strength of polycrystals
66. Review of Mechanical Properties of Ti-6Al-4V Made by Laser-Based Additive Manufacturing Using Powder Feedstock10.1007/s11837-015-1759-z ↗
67. Additive manufacturing and postprocessing of Ti-6Al-4V for superior mechanical properties10.1557/mrs.2016.215 ↗
68. Unravelling the physics of size-dependent dislocation-mediated plasticity10.1038/ncomms6926 ↗
69. Assessment of geometrically necessary dislocation levels derived by 3D EBSD10.1016/j.actamat.2015.06.051 ↗
70. Hall–Petch relationship and dislocation model for deformation of ultrafine-grained and nanocrystalline metals10.2320/matertrans.MA201310 ↗
71. The role of the solidification structure on orientation-dependent hardness in stainless steel 316L produced by laser powder bed fusion10.1016/j.msea.2021.142493 ↗