Effects of fibrous Cr phase on the adiabatic shearing anisotropic behavior of the Cu-15Cr in-situ composite
Source abstract
Abstract
The effects of fibrous Cr phase on the adiabatic shearing anisotropic behavior of the Cu-15Cr in-situ composite model alloy were firstly studied by a split Hopkinson pressure bar (SHPB), Optical Microscope (OM), and X-ray diffraction (XRD) technique. Specimens were loaded along the rolling direction (Cu-15Cr-0°) and perpendicular to the rolling direction (Cu-15Cr-90°). The experimental and analysis results showed that there were differences in the number of phase interfaces and phase interface distance that the shear stress crossed when sheared along with different directions due to the directional arrangement of the fibrous Cr phases, which caused the strain hardening, strain rate hardening and thermal softening of the Cu-15Cr in-situ composite were anisotropic. The Cu-15Cr-90° specimen possessed lower strain rate hardening and higher thermal softening at the same strain rate, and the strain hardening rate was similar to that of the Cu-15Cr-0° specimen as the shearing process proceeded, so the Cu-15Cr-90° specimen was more prone to adiabatic shearing than the Cu-15Cr-0° specimen. In addition, a splitting crack was produced at the Cr phase and matrix interface in the Cu-15Cr-0° specimen due to the additional tensile stress produced in the Cr phase during shearing. The perpendicular Cr phase in the Cu-15Cr-90° specimen was deflected parallel to the shear stress during shearing, so it was not easy to produce splitting cracks. However, the tip of the Cr phase without deflection was more likely to possess high additional tensile stress, so the crack in the Cu-15Cr-90° specimen was extended along the edge of the adiabatic shear region at the tip of the Cr phase.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Microstructure and mechanical properties · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Failure of metals i: brittle and ductile fracture10.1016/j.actamat.2015.12.034 ↗
2. Ductile fracture of high strength steels with morphological anisotropy, Part I: characterization, testing, and void nucleation law10.1016/j.engfracmech.2021.107569 ↗
3. Ductile fracture of high strength steels with morphological anisotropy, Part II: nonlocal micromechanics-based modeling10.1016/j.engfracmech.2021.107716 ↗
4. Effect of spherical inclusions on fatigue anisotropy of HSLA-100 steel10.1080/02670836.2021.1890908 ↗
5. Effect of texture on crack initiation toughness and the corresponding anisotropy in ductile fracture resistance of thin Zircaloy-4 sheets of Indian PHWR core component10.1016/j.jnucmat.2020.152189 ↗
6. Analysis of anisotropy mechanism in the mechanical property of titanium alloy tube formed through hot flow forming10.1016/j.jmst.2021.01.038 ↗
7. Anisotropic plasticity and fracture of three 6000-series aluminum alloys
8. Impact of second phase morphology and orientation on the plastic behavior of dual-phase steels10.1016/j.ijplas.2019.02.005 ↗
9. Quantitative assessment of the impact of second phase particle arrangement on damage and fracture anisotropy10.1016/j.actamat.2018.02.003 ↗
10. On the influence of particle distribution and reverse loading on damage mechanisms of ductile steels10.1016/j.msea.2008.05.033 ↗
11. A constitutive model for plastically anisotropic solids with non-spherical voids10.1016/j.jmps.2010.03.007 ↗
12. Anisotropic compressive deformation behaviors of tungsten fiber reinforced Zr-based metallic glass composites10.1016/j.msea.2012.12.080 ↗
13. Meyers · 1994
14. Temperature increases and thermoplastic microstructural evolution in adiabatic shear bands in a high-strength and high-toughness 10 wt% Ni steel10.1016/j.actamat.2020.116568 ↗
15. Effect of the grain boundary character distribution on the self-organization of adiabatic shear bands in 1Cr18Ni9Ti austenitic stainless steel10.1007/s10853-019-03377-z ↗
16. Forecast of adiabatic shear band formation in two commercial ultra-high-strength rrmor steels by split Hopkinson pressure bar10.1007/s11661-020-05814-0 ↗
17. Fracture mechanisms in flat and cylindrical tensile specimens of TRIP-TWIP β-metastable Ti-12Mo alloy10.1016/j.actamat.2021.117294 ↗
18. The failure mechanism at adiabatic shear bands of titanium alloy: high-precision survey using precession electron diffraction and geometrically necessary dislocation density calculation10.1016/j.msea.2019.01.016 ↗
19. Study on the microstructural characteristics of adiabatic shear band in solid-solution treated ZK60 magnesium alloy10.1016/j.matchar.2019.109840 ↗
20. The deformation mechanism and adiabatic shearing behavior of extruded Mg-8.0Al-0.1Mn alloy in different heat treated states under high-speed impact load10.1016/j.jmrt.2021.01.114 ↗
21. The high-strain-rate constitutive behavior and shear response of pure magnesium and AZ31B magnesium alloy10.1007/s11661-021-06312-7 ↗
22. Microstructural evolution of adiabatic shear bands in pure copper during impact at high strain rate10.1016/j.msea.2017.11.027 ↗
23. Effects of strain rates on dynamic deformation behavior of Cu-20Ag alloy10.1016/j.jmst.2020.11.043 ↗
24. Adiabatic shear band localization in an Al–Zn–Mg–Cu alloy under high strain rate compression10.1016/j.jmrt.2020.02.024 ↗
25. Experimental investigation of the dynamic impact responses of as-cast and homogenized A535 aluminum alloy
26. High susceptibility to adiabatic shear banding and high dynamic strength in tungsten heavy alloys with a high-entropy alloy matrix10.1016/j.jallcom.2020.157796 ↗
27. High strain-rate compressive deformation behavior of the Al0.1CrFeCoNi high entropy alloy10.1016/j.matdes.2015.07.161 ↗
28. Thermodynamics-kinetics of twinning/martensitic transformation in Fe50Mn30Co10Cr10 high-entropy alloy during adiabatic shearing10.1016/j.scriptamat.2020.02.024 ↗
29. Adiabatic shear susceptibility of Fe50Mn30Co10Cr10 high-entropy alloy10.1007/s11661-020-05641-3 ↗
30. High-velocity deformation of Al0.3CoCrFeNi high entropy alloy: Remarkable resistance to shear failure
31. Adiabatic shear localization in the CrMnFeCoNi high entropy alloy10.1016/j.actamat.2018.03.040 ↗
32. Adiabatic shear failure in brittle solids10.1016/j.ijimpeng.2011.01.001 ↗
33. Dynamic compressive mechanical properties of the spiral tungsten wire reinforced Zr-based bulk metallic glass composites
34. High strain rate compressive behaviors and adiabatic shear band localization of 3-D carbon/epoxy angle-interlock woven composites at different loading directions10.1016/j.compstruct.2018.12.037 ↗
35. Numerical simulations of adiabatic shear localization in textured FCC metal based on crystal plasticity finite element method10.1016/j.msea.2018.08.105 ↗
36. The correlation of texture and the formation of the adiabatic shear band in 7XXX aluminum alloy during dynamic loading10.1155/2021/4022424 ↗
37. Formation of adiabatic shear band in metal matrix composites10.1016/j.ijsolstr.2004.05.023 ↗
38. Effect of fibrous orientation on dynamic mechanical properties and susceptibility to adiabatic shear band of tungsten heavy alloy fabricated through hot-hydrostatic extrusion10.1016/j.msea.2007.10.012 ↗
39. Preparation and anisotropic compressive deformation behaviors of tungsten fiber reinforced Cu-Zn matrix composite10.1016/j.msea.2017.09.110 ↗
40. Correlation between the cold-working and aging treatments in a Cu-15 wt Pct Cr in situ composite10.1007/s11661-998-0044-y ↗
41. The thermo-mechanical behaviour of Cu-Cr in-situ composite10.1023/B:JMSC.0000025831.58057.52 ↗
42. Microstructure and texture evolution of rolled plate for Cu–15Cr in-situ composite10.1007/s12540-020-00738-1 ↗
43. Thermal behavior and strength of continuous filament Cu-Nb composites10.1063/1.338928 ↗
44. Comparison of the strengths and microstructures of Cu-20%Ta and Cu-20%Nb in situ composites10.1016/0001-6160(88)90238-6 ↗
45. . Development of high-strength, high-conductivity Cu-Ag alloys for high-field pulsed magnet use10.1063/1.105813 ↗
46. Microstructure and strengthening model of Cu–Fe in-situ composites10.3390/ma13163464 ↗
47. Effects of Cr addition on the constitutive equation and precipitated phases of copper alloy during hot deformation10.1016/j.matdes.2020.108613 ↗
48. Improving the mechanical performance of Cu-Cr alloy by dissolving Cu in the Cr second phase10.1016/j.matchar.2021.111104 ↗
49. Structures and residual stresses of Cr fibers in Cu-15Cr in-situ composites10.1007/s11661-001-0131-9 ↗
50. In-situ composite Cu-Cr contact cables with high strength and high conductivity
51. Property and thermal stability of in situ composite Cu-Cr alloy contact cable10.1016/j.jmatprotec.2004.08.013 ↗
52. B. Beausir, J.-J. Fundenberger , Analysis Tools for Electron and X-ray diffraction. ATEX - Software, Université de Lorraine - Metz. 〈www.atex-software.eu〉, 2017.
53. Review of the development of hopkinson pressure bar technique in China
54. Effect of grain size on adiabatic shear susceptibility of copper10.1007/s11665-021-05572-z ↗
55. Dislocation-particle interactions
56. On precipitate induced hardening in crystal plasticity: theory
57. J. Sun. Coupling effect of second phase and phase interface on deformation behaviours in microscale Ti-55531 pillars10.1016/j.jallcom.2019.153421 ↗
58. Extension of solid solubility and structural evolution in nano-structured Cu-Cr solid solution induced by high-energy milling10.3390/ma13235532 ↗
59. Improvement of interfacial bonding and mechanical properties of Cu-Al2O3 composite by Cr-nanoparticle-induced interfacial modification10.1016/j.jallcom.2016.11.055 ↗
60. Evolution of the microstructure and properties of a Cu-Cr-(Mg) alloy upon thermomechanical treatment
61. Effects of trapping dislocations within small crystals on their deformation behavior10.1016/j.actamat.2009.06.053 ↗
62. S. Suresh. Strain rate sensitivity of Cu with nanoscale twins10.1016/j.scriptamat.2006.04.046 ↗
63. Some aspects of deformation behavior of coarse multiphase metallic materials10.1007/BF03024538 ↗
64. Small crack formation in a low carbon steel with banded ferrite–pearlite structure10.1016/j.msea.2004.09.058 ↗
65. An examination of adiabatic shearing behavior in ZK60 alloy with different states of heat treatment10.1016/j.msea.2016.12.117 ↗