Size effects and the deformation behaviour of a dilute Mg-Zn-Ca alloy subjected to cyclic four-point bending
Source abstract
Abstract
In biodegradable stents made from dilute Mg-Zn-Ca alloys a small number of grains constitute the thickness of a sample limiting the mechanical constrain typically seen in polycrystalline alloys. At the same time such stents are exposed to complex loading conditions, which could potentially lead to premature failure particularly in the presence of limited slip mode activation. In order to improve our understanding of the prevailing micromechanics for such conditions hot-rolled, thin strip samples were produced with thickness to grain size ratios (t/D) of 100 and 17. Samples were extracted from such thin strips and subjected to interrupted cyclic four-point bending in order to study the in-grain misorientation axis (IGMA) evolution of selected grains during cyclic loading using quasi-in-situ electron back-scattered diffraction (EBSD). Grains were selected at the tensile and compressive faces of samples, and in the vicinity of the neutral band. Analysis of the evolution of IGMA and misorientation profiles during the bending showed that extension twinning was the dominant deformation mode in the compressive region for both t/D ratios. In addition, non-basal -type slip systems were active as a result of work hardening. In the tensile region, the activity of -type non-basal slip systems was observed for the t/D of 100, but basal/double basal slip was the dominant deformation mode for the t/D of 17. No signs of failure were observed for the sample with a t/D of 17 at the tensile region, implying that these basal slip modes can accommodate deformation largely without the assistance of other deformation modes. The neutral band evolution was mapped using grain orientation spread (GOS) analysis. In contrast to the continuum mechanics solution, a neutral band was observed instead of an axis. The position of the neutral band was dependant on the local orientation organization of the grains and the extent of work-hardening.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Effects of grain size, texture and twinning on mechanical properties and work-hardening behavior of AZ31 magnesium alloys10.1016/j.msea.2011.07.076 ↗
2. Acta Biomaterialia Mechanical property, biocorrosion and in vitro biocompatibility evaluations of Mg – Li –( Al)–( RE) alloys for future cardiovascular stent application q10.1016/j.actbio.2013.01.032 ↗
3. The effect of strain heterogeneity on the deformation and failure behaviors of E-form Mg alloy sheets during a mini-V-bending test10.1016/j.jallcom.2017.02.176 ↗
4. Biodegradable Mg-Zn-Ca-Sr bulk metallic glasses with enhanced corrosion performance for biomedical applications10.1016/j.matdes.2014.10.085 ↗
5. Effect of initial texture on the bending behavior, microstructure and texture evolution of ZK60 magnesium alloy during the bending process10.1016/j.jallcom.2017.12.084 ↗
6. Processing and properties of biodegradable magnesium microtubes for using as vascular stents: a brief review10.1007/s12540-019-00285-4 ↗
7. Biodegradable metals for cardiovascular stent application: Interests and new opportunities10.3390/ijms12074250 ↗
8. A novel biodegradable Mg-Nd-Zn-Zr alloy with uniform corrosion behavior in artificial plasma10.1016/j.matlet.2012.08.012 ↗
9. Enhanced biocompatibility and long-term durability in vivo of Mg-Nd-Zn-Zr alloy for vascular stent application10.1016/j.jallcom.2017.05.280 ↗
10. A numerical corrosion-fatigue model for biodegradable Mg alloy stents10.1016/j.actbio.2019.08.004 ↗
11. Mechanical property, biocorrosion and in vitro biocompatibility evaluations of Mg-Li-(Al)-(RE) alloys for future cardiovascular stent application10.1016/j.actbio.2013.01.032 ↗
12. A promising biodegradable magnesium alloy suitable for clinical vascular stent application10.1038/srep46343 ↗
13. The processing of Mg alloy micro-tubes for biodegradable vascular stents10.1016/j.msec.2014.12.024 ↗
14. Fabrication of Mg alloy tubes for biodegradable stent application10.1016/j.msec.2013.07.033 ↗
15. Stoeckel · A Surv. Stent Des. · 2002 · 11 · 137
16. A review of geometrical and microstructural size effects in micro-scale deformation processing of metallic alloy components10.1016/j.ijmachtools.2016.07.006 ↗
17. The size effect on micro deformation behaviour in micro-scale plastic deformation10.1016/j.matdes.2010.06.011 ↗
18. Influence of size effect on the springback of sheet metal foils in micro-bending10.1016/j.commatsci.2011.04.002 ↗
19. Effects of the initial dislocation density on size effects in single-crystal magnesium10.1016/j.actamat.2013.03.019 ↗
20. Geometry and grain size effects on the fracture behavior of sheet metal in micro-scale plastic deformation10.1016/j.matdes.2011.06.039 ↗
21. Size effect on the tensile strength of fine-grained copper
22. L.V. Raulea, A.M. Goijaerts, L.E. Govaert, F.P.T. Baaijens, Size effects in the processing of thin metal sheets, 115 (2001) 44–48.10.1016/S0924-0136(01)00770-1 ↗
23. An experimental assessment of grain size effects in the uniaxial straining of thin Al sheet with a few grains across the thickness10.1016/j.msea.2005.12.029 ↗
24. 11-22}〈1123〉 Slip system in magnesium10.1016/0001-6160(73)90141-7 ↗
25. Modeling of the flow stress behavior and microstructural evolution during hot deformation of Mg-8Al-1.5Ca-0.2Sr magnesium alloy10.1016/j.jma.2014.05.001 ↗
26. Strain hardening behaviour and the Taylor factor of pure magnesium10.1080/14786430801968611 ↗
27. Microstructure evolution under compressive plastic deformation of magnesium at different temperatures and strain rates10.1016/S0921-5093(01)01297-7 ↗
28. T.W. Duerig, D.E. Tolomeo, M. Wholey, T.W. Duerig, D.E. Tolomeol, M. Wholey, An overview of superelastic stent design An overview of superelastic stent design, 5706 (2010). https://doi.org/10.1080/13645700009169654.10.1080/13645700009169654 ↗
29. On the inhomogeneous deformation behavior of magnesium alloy beam subjected to bending10.1016/j.ijplas.2021.103180 ↗
30. Geometrically necessary twins in bending of a magnesium alloy10.1016/j.msea.2015.08.027 ↗
31. Effects of grain size on shift of neutral layer of AZ31 magnesium alloy under warm condition10.1016/S1003-6326(15)63658-5 ↗
32. Evolution of neutral layer and microstructure of AZ31B magnesium alloy sheet during bending10.1016/j.matlet.2013.02.055 ↗
33. In-situ investigation on the microstructure evolution and plasticity of two magnesium alloys during three-point bending10.1016/j.ijplas.2015.05.010 ↗
34. Microstructure evolution of Mg-3%Al-1%Zn alloy tube during warm bending10.1007/s10853-011-6234-9 ↗
35. Crystallographic classification of kink bands in an extruded Mg – Zn – Y alloy using intragranular misorientation axis analysis10.1016/j.actamat.2012.12.026 ↗
36. V. Tong, E. Wielewski, B. Britton, Characterisation of slip and twinning in high rate deformed zirconium with electron backscatter diffraction, (2018) 1–45. http://arxiv.org/abs/1803.00236.
37. Acta Materialia Con fi guration of dislocations in low-angle kink boundaries formed in a single crystalline long-period stacking ordered Mg-Zn-Y alloy10.1016/j.actamat.2018.03.034 ↗
38. Z.R. Zeng, Y.M. Zhu, S.W. Xu, M.Z. Bian, C.H.J. Davies, N. Birbilis, J.F. Nie, Acta Materialia Texture evolution during static recrystallization of cold-rolled magnesium alloys, 105 (2016). https://doi.org/10.1016/j.actamat.2015.12.045.10.1016/j.actamat.2015.12.045 ↗
39. Distribution characteristics of in-grain misorientation axes in cold-rolled commercially pure titanium and their correlation with active slip modes
40. The evolution of in-grain misorientation axes (IGMA) during deformation of wrought magnesium alloy AZ31
41. Four-point-bending device for bending moment controlled cyclic reverse loading on plate materials and its application on AZ31B magnesium sheets10.1016/j.ijfatigue.2017.12.011 ↗
42. In-situ investigation on the microstructure evolution and plasticity of two magnesium alloys during three-point bending10.1016/j.ijplas.2015.05.010 ↗
43. Basal slip mediated tension twin variant selection in magnesium WE43 alloy10.1016/j.actamat.2019.03.018 ↗
44. A quantitative study of stress fields ahead of a slip band blocked by a grain boundary in unalloyed magnesium10.1038/s41598-020-59684-y ↗
45. Mechanical properties and Hall-Petch relationship of the extruded Mg-Zn-Y alloys with different volume fractions of icosahedral phase10.1016/j.jallcom.2018.08.121 ↗
46. Effects of solute and second-phase particles on the texture of Nd-containing Mg alloys
47. Role of solute in the texture modification during hot deformation of Mg-rare earth alloys
48. Promotion of texture weakening in magnesium by alloying and thermomechanical processing
49. Understanding room-temperature deformation behavior in a dilute Mg–1.52Zn–0.09Ca (mass%) alloy sheet with weak basal texture10.1016/j.msea.2022.143638 ↗
50. Formation of anomalous twinning and its effect on texture development in a cold-rolled Mg-Zn-Ca alloy sheet10.1016/j.matchar.2021.111507 ↗
51. Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing10.1016/j.ijplas.2022.103412 ↗
52. Simulation-aided analysis on mechanical properties of dilute Mg-Zn-Ca alloy sheets10.1016/j.jallcom.2022.164285 ↗
53. Coupling thermomechanical processing and alloy design to improve textures in Mg-Zn-Ca sheet alloys10.1007/s11837-021-04630-0 ↗
54. Synergization of ductility and yield strength in a dilute quaternary Mg-Zn-Gd-Ca alloy through texture modification and Guinier–Preston zone10.1016/j.scriptamat.2021.114257 ↗
55. Microstructures and textures of pure magnesium deformed in plane-strain compression10.1016/j.scriptamat.2004.07.002 ↗
56. Texture effect on microyielding of wrought magnesium alloy AZ3110.1016/j.msea.2011.01.046 ↗
57. Unusual spreading of strain neutral layer in AZ31 magnesium alloy sheet during bending10.3390/ma15248880 ↗
58. K. Tavighi, Microstructural Characterization of a Dilute Magnesium Alloy During Cyclic Four-point Bending, Monash University, 2021.
59. Effects of grain size, texture and twinning on mechanical properties and work-hardening behaviors of pure Mg10.1016/j.msea.2013.04.094 ↗
60. G. Zhu, L. Wang, H. Zhou, J. Wang, Y. Shen, P. Tu, H. Zhu, W. Liu, P. Jin, X. Zeng, Improving ductility of a Mg alloy via non-basal slip induced by Ca addition, 120 (2019) 164–179. https://doi.org/10.1016/j.ijplas.2019.04.020.10.1016/j.ijplas.2019.04.020 ↗
61. Prediction of thermal cross-slip stress in magnesium alloys from a geometric interaction model10.1016/j.actamat.2012.01.004 ↗
62. Twinning and its related work hardening during the ambient extrusion of a magnesium alloy10.1016/j.msea.2013.03.078 ↗
63. An experimental and numerical study of texture change and twinning-induced hardening during tensile deformation of an AZ31 magnesium alloy rolled plate10.1016/j.msea.2012.11.018 ↗
64. Nucleation and propagation of { 1 0 1 ¯ 2} twins in AZ31 magnesium alloy10.1016/j.actamat.2015.08.024 ↗
65. An insight into neutral layer shifting in tube bending10.1016/j.ijmachtools.2017.11.013 ↗