Effects of micron-sized Si particles on the static and dynamic mechanical properties and fracture behavior of Al-xSi alloy sheets
Source abstract
Abstract
In this paper, a comprehensive analysis was conducted on the effects of micron-sized Si particles on the microstructure, static and dynamic mechanical properties, and fracture behavior of wrought Al-xSi alloy sheets. The investigation employed techniques such as optical microscope, scanning electron microscope, laser scanning confocal microscope, transmission electron microscope, tensile testing and fatigue testing. The results show that when the Si content is below 12 wt%, the size of the Si particles in the alloy sheets does not exceed 3 μm, and their quantity gradually increases with higher Si content. As the Si content increases, the grain size of the alloy sheets is refined from 63 μm to 8 μm. The alloy strength initially increases and then slightly decreases with further Si addition. while elongation exhibits a general downward trend. The tensile fracture modes of Al-(1–12 wt%) Si alloy sheets are all ductile fractures. The fatigue life of Al-xSi alloy sheets first extends and then shortens as the Si content increases. With the increase of Si content, the yield strength of the alloy sheets gradually increases from 47.6 MPa to 85.7 MPa. When the Si content is 12 wt%, the tensile strength reaches the maximum value of 185.4 MPa. With the increase of Si content, the elongation of the alloy sheet first increases slightly, reaching 35.0 %, when the Si content increases to 15 wt%, the elongation gradually decreases to 17.5 %. As the Si content increases, the fatigue life of the alloy sheets gradually extends. When the Si content reaches 12 wt%, the alloy sheet achieves its maximum fatigue life, reaching 9.97 × 10 5–1.97 × 10⁶ cycles, approximately 11–14 times longer than that of the Al-1 wt% Si alloy sheet. However, with a further increase in Si content to 15 wt%, the fatigue life significantly decreases to 4.08 × 10⁵–4.70 × 10⁵ cycles, shortening by approximately 59–76 %. The fatigue crack source of Al-xSi alloy sheets gradually changes from the persistent slip bands on the surface of the sheet to the large-sized Si particles on the surface of the sheet. The functional relationship between the fatigue life of Al-xSi alloy sheets as the Si content changes is established, and the fatigue life influencing factor I Si is introduced to quantitatively describe the influence of the number of micron-sized eutectic Si particles on the fatigue life or fatigue properties of the alloy sheets. This study provides important scientific insights for optimizing alloy property and meeting diverse industrial demands, thereby promoting the application and development of wrought Al-Si alloy in broader fields.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Characterization of tensile fracture in heavily alloyed Al-Si piston alloy10.1016/S1002-0071(12)60073-2 ↗
2. Plastic deformation behavior of aluminum casting alloy A356/35710.1007/s11661-004-0216-3 ↗
3. Silicon morphology modification in the eutectic Al-Si alloy using mechanical mold vibration10.1016/j.msea.2004.09.038 ↗
4. Growth mechanisms of silicon in Al-Si alloy10.1016/0022-0248(85)90308-2 ↗
5. Microstructural effects on the tensile and fracture behavior of aluminum casting alloy A356/35710.1007/s11661-003-0189-7 ↗
6. Microstructure evolution of Al-Si hypoeutectic alloy prepared by controlled diffusion solidification10.1007/s00170-022-09075-6 ↗
7. Modification of hypoeutectic Al-Si alloy with scandium10.1016/j.jallcom.2008.10.016 ↗
8. Modeling and analysis of the effects of processing parameters on the performance characteristics in the high pressure die casting process of Al-Si alloy10.1007/s00170-008-1559-5 ↗
9. The effect of Si content on the microstructure and mechanical properties of Al-1.2Mg-xSi-1.2Cu-0.6Mn cast alloy
10. High temperature tensile and wear behaviour of aluminum silicon alloy10.1016/j.msea.2010.09.020 ↗
11. Simultaneously improved strength and ductility in aluminum matrix composite with heterogeneous structures under impact loadings10.1016/j.jmrt.2022.12.187 ↗
12. Effect of eutectic Si particles on the defect susceptibility of tensile properties to microporosity variation in Al-xSi binary alloy10.1016/j.msea.2016.09.111 ↗
13. Tension-compression mechanical behavior and corresponding microstructure evolution of cast A356-T6 aluminum alloy10.1016/j.msea.2021.141613 ↗
14. The effect of Si content on microstructure and mechanical properties of Al-Si alloy
15. Effect of Si content on microstructure and mechanical properties of Al-Si-Mg alloy10.1016/j.matdes.2013.07.067 ↗
16. Effect of severe plastic deformation on tensile properties of a cast Al-11mass% Si alloy10.1016/j.msea.2004.12.038 ↗
17. Effect of Si content on the microstructure and properties of Al-Si alloy fabricated using hot extrusion10.1557/jmr.2017.97 ↗
18. Cyclic deformation behavior of a cast aluminum alloy10.1016/j.msea.2009.04.037 ↗
19. A systematic investigation of fracture mechanisms in Al-Si based eutectic alloy-effect of Si modification10.1016/j.msea.2013.09.019 ↗
20. The effect of the flake to fiber transition in silicon morphology on the tensile properties of Al-Si eutectic alloy10.1016/j.msea.2010.09.008 ↗
21. Refinement of eutectic grains by combined addition of strontium and boron in near-eutectic Al-Si alloy10.1016/j.scriptamat.2007.08.026 ↗
22. A modeling of residual stress in stretched aluminum alloy plate10.1016/j.jmatprotec.2012.06.019 ↗
23. Investigating the influences of Fe, Mn and Mo additions on the evolution of microstructure and mechanical performances of Al-Si-Mg cast alloy10.1016/j.jmrt.2023.05.234 ↗
24. Scatter in fatigue life due to effects of porosity in cast A356-T6 aluminum-silicon alloy10.1007/s11661-003-0153-6 ↗
25. The effect of porosity on the fatigue life of cast aluminium-silicon alloy
26. The influence of modified intermetallics and Si particles on fatigue crack paths in a cast A356 Al alloy10.1046/j.1460-2695.2000.00239.x ↗
27. Fatigue crack growth characteristics in cast Al-Si-Mg alloy
28. Brittle failure of hypereutectic Al-Si alloy component10.1007/s11668-015-9996-6 ↗
29. Porosity and the fatigue behavior of hypoeutectic and hypereutectic aluminum–silicon casting alloy10.1016/j.ijfatigue.2007.08.012 ↗
30. Investigation of adding silicon on fatigue properties of aluminum based alloy10.1007/s12633-020-00500-7 ↗
31. Microstructure-based fatigue life prediction for cast A356-T6 aluminum-silicon alloy10.1007/BF02693159 ↗
32. Efects of dendrite cell size and eutectic Si particle morphologyon fatigue crack growth in cast and HIPed AC4CH alloy10.2320/matertrans1989.40.685 ↗
33. Thermo-mechanical fatigue behavior and life prediction of the Al-Si piston alloy10.1016/j.msea.2017.12.099 ↗
34. Fatigue crack growth mechanisms in Al-Si-Mg alloy10.1179/sur.2004.20.6.416 ↗
35. Fatigue behaviour of hot worked cast aluminium alloy with different Si contents10.1179/1743133611Y.0000000012 ↗
36. Effect of heat treatment and loading path on non-proportional fatigue behavior and fracture characteristics of an Al-Si casting alloy10.1007/s11665-022-07400-4 ↗
37. On the role of internal defects in the fatigue damage process of a cast Al-Si-Cu alloy10.1016/j.ijfatigue.2018.07.012 ↗
38. Microstructural effects on short fatigue crack propagation in cast Al-Si alloy10.1016/j.ijfatigue.2023.107788 ↗
39. Effects of eutectic silicon particles on tensile properties and fracture toughness of A356 aluminum alloy fabricated by low-pressure-casting, casting-forging and squeeze-casting processes10.1016/j.jallcom.2007.07.038 ↗
40. Yield strength prediction of rolled Al-(1.44-12.40)Si-0.7Mg alloy sheets under T4 condition10.1016/S1003-6326(20)65359-6 ↗
41. Fatigue crack nucleation and microstructurally small crack growth mechanisms in high strength aluminum alloy10.1016/j.ijfatigue.2020.105790 ↗
42. Recent development of superplasticity in aluminum alloy: a review10.3390/met10010077 ↗
43. Study of fatigue crack growth behaviour of Al-Mg and Al-Mg-Sc-Zr alloy10.1080/02670836.2022.2163529 ↗
44. Micromechanisms of multistage fatigue crack growth in a high-strength aluminum alloy10.1016/j.actamat.2006.11.009 ↗