In-situ study on the effect of Li concentration on hydrogen microporosity evolution in Al-Li alloys by synchrotron X-ray radiography
Source abstract
Abstract
The nucleation and growth of hydrogen microporosity during the solidification of Al-Li alloys were in situ observed by synchrotron radiation X-ray radiography, and the effect of initial Li concentration on its evolution kinetics was investigated. The results show that the high Li concentration effectively contributes to the high-temperature nucleation effect of hydrogen microporosity during the solidification of Al-Li alloys, and significantly increases the nucleation and growth rates of hydrogen microporosity. When the initial Li concentration was 2.0 wt%, the nucleation supersaturation of hydrogen microporosity was 1.96, which was 3.5 times higher than that at low Li concentration (1.5 wt%), and the growth rate was up to 2.61 μm/s. In addition, the quantitative results of the final size, morphology, and distribution of the hydrogen microporosity based on 3D X-ray computed tomography (X-CT) showed that high Li concentration not only increased the volume of monolithic hydrogen microporosity, and increased the total number of microporosities, but also increased the degree of irregularity of hydrogen microporosity. The in-situ observation results can provide a new dataset for the establishment and validation of the hydrogen microporosity model of Al-Li alloys.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Fusion materials and technologies · Corrosion Behavior and Inhibition
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. Addressing the strength-ductility trade-off in a cast Al-Li-Cu alloy—Synergistic effect of Sc-alloying and optimized artificial ageing scheme10.1016/j.jmst.2021.01.036 ↗
2. Quantifying the kinetics of δ′ precipitates in a novel Al–Li–Cu–Mg alloy during two-step aging by small-angle neutron scattering10.1016/j.msea.2023.144963 ↗
3. Achieving highest Young’s modulus in Al-Li by tracing the size and bonding evolution of Li-rich precipitates10.1016/j.jmst.2022.10.052 ↗
4. Effects of microstructure coarsening and casting pores on the tensile and fatigue properties of cast A356-T6 aluminum alloy: a comparative investigation10.1016/j.msea.2022.144106 ↗
5. In-situ X-ray tomography investigation of pore damage effects during a tensile test of a Ni-based single crystal superalloy10.1016/j.matchar.2021.111180 ↗
6. Pore space characteristics and corresponding effect on tensile properties of Inconel 625 fabricated via laser powder bed fusion10.1016/j.msea.2019.138525 ↗
7. On the relationship between internal porosity and the tensile ductility of aluminium alloy die-castings10.1016/j.msea.2020.139107 ↗
8. The effect of manufacturing defects on the fatigue life of selective laser melted Ti-6Al-4V structures10.1016/j.matdes.2020.108708 ↗
9. The role of defects and critical pore size analysis in the fatigue response of additively manufactured IN718 via crystal plasticity10.1016/j.matdes.2018.04.022 ↗
10. Investigation of the effect of porosity on the high cycle fatigue behaviour of cast Al-Si alloy by X-ray micro-tomography10.1016/j.ijfatigue.2017.09.012 ↗
11. The effect of porosity on fatigue of die cast AM6010.1007/s11661-016-3511-x ↗
12. Effect of Micro-porosities on fatigue behavior in aluminum die castings by 3D X-ray tomography inspection10.2355/isijinternational.54.511 ↗
13. Quantifying the effect of porosity on the evolution of deformation and damage in Sn-based solder joints by X-ray microtomography and microstructure-based finite element modeling10.1016/j.actamat.2012.03.048 ↗
14. Effect of porosity and density on the mechanical and microstructural properties of sintered 316L stainless steel implant materials10.1016/j.matdes.2013.09.058 ↗
15. Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects
16. Quantifying the effects of hydrogen concentration and cooling rates on porosity formation in Al–Li alloys10.1016/j.jmrt.2023.08.017 ↗
17. The solubility of hydrogen in molten aluminum alloys10.1007/BF02663209 ↗
18. Predicting hydrogen microporosity in long solidification range ternary Al-Cu-Li alloys by coupling CALPHAD and cellular automata model10.1016/j.commatsci.2023.112120 ↗
19. Bubble growth, intermetallic compounds dissolution and their interactions during heating of an Al-5wt%Mn alloy by in-situ synchrotron radiography10.1016/j.jallcom.2019.153554 ↗
20. A model for coupling prediction of inverse segregation and porosity for up-vertical unidirectional solidification of Al–Cu alloys10.1016/j.jallcom.2019.05.106 ↗
21. Hydrogen porosity in directional solidified aluminium-copper alloys:in situ observation10.1016/S1359-6454(97)00081-5 ↗
22. Accelerating pore nucleation and eutectic Si growth kinetics by increasing Cu and Sc for Al-Si-Mg alloys: In-situ observation10.1016/j.jallcom.2021.159173 ↗
23. Measuring the nucleation of hydrogen porosity during the solidification of aluminium-copper alloys10.1016/S1359-6462(96)00411-3 ↗
24. In-situ study on hydrogen bubble evolution in the liquid Al/solid Ni interconnection by synchrotron radiation X-ray radiography10.1016/j.jmst.2019.03.007 ↗
25. Hydrogen solubility in liquid and solid pure aluminum—critical review of measurement methodologies and reported values10.4236/msa.2022.134011 ↗
26. Reducing porosity and optimizing performance for Al-Cu-based alloys with large solidification intervals by coupling travelling magnetic fields with sequential solidification10.1016/j.jmst.2020.11.035 ↗
27. Hydrogen microporosity evolution and dendrite growth during long solidification of Al-Cu-Li alloys: Modeling and experiment10.1016/j.jmatprotec.2023.118135 ↗
28. Modeling of hydrogen porosity formation during solidification of dendrites and irregular eutectics in Al–Si alloys10.1016/j.mtla.2018.09.030 ↗
29. Predicting gas and shrinkage porosity in solidification microstructure: a coupled three-dimensional cellular automaton model10.1016/j.jmst.2020.02.028 ↗
30. Modeling of gas porosity and microstructure formation during dendritic and eutectic solidification of ternary Al-Si-Mg alloys10.1016/j.jmst.2020.11.008 ↗
31. Numerical and experimental investigation of microporosity formation in a ternary Al–Cu–Si alloy10.1016/j.jallcom.2010.04.244 ↗
32. Multiscale modeling of the influence of Fe content in a Al–Si–Cu alloy on the size distribution of intermetallic phases and micropores
33. Modeling of microstructure formation with gas porosity growth during columnar dendritic solidification of aluminum alloys10.1016/j.jmrt.2021.12.078 ↗
34. The kinetics of Fe-rich intermetallic formation in aluminium alloys: In situ observation10.1016/j.scriptamat.2008.11.048 ↗
35. 4D synchrotron X-ray tomographic quantification of the transition from cellular to dendrite growth during directional solidification10.1016/j.actamat.2016.07.002 ↗
36. Accelerating pore nucleation and eutectic Si growth kinetics by increasing Cu and Sc for Al-Si-Mg alloys: In-situ observation10.1016/j.jallcom.2021.159173 ↗
37. Simulation of the three-dimensional morphology of solidification porosity in an aluminium–silicon alloy10.1016/S1359-6454(03)00411-7 ↗
38. Pore formation during solidification of aluminum: reconciliation of experimental observations, modeling assumptions, and classical nucleation theory10.1007/s11661-017-4438-6 ↗
39. J. Wang, In-situ Observation and Mathematical Modelling of the Nucleation and Growth of Intermetallics and Micropores During the Solidification of Aluminium Alloys, Imperial College London (2009).
40. Quantitative prediction of microporosity in aluminum alloys10.1016/j.jmatprotec.2007.03.072 ↗
41. Characterization of microshrinkage casting defects of Al–Si alloys by X-ray computed tomography and metallography10.1016/j.ijfatigue.2012.01.006 ↗
42. The solubility of hydrogen in liquid binary Al-Li alloys10.1007/BF02654206 ↗
43. Attempt to predict hydrogen solubility limits in liquid multicomponent aluminum alloys10.1016/1359-6462(95)00591-9 ↗
44. Statistical modeling of microstructure and defect population effects on the fatigue performance of cast A356-T6 automotive components10.1016/j.msea.2006.07.003 ↗
45. Influence of porosity characteristics on the variability in mechanical properties of high pressure die casting (HPDC) AlSi7MgMn alloys10.1016/j.jmapro.2020.04.071 ↗
46. Quantitative analysis of 3D pore characteristics effect on the ductility of HPDC Al–10Si-0.3 Mg alloy through X-ray tomography10.1016/j.jmrt.2023.09.179 ↗
47. Effects of hydrogen micro pores on mechanical properties in A2024 aluminum alloys10.2320/matertrans.L-M2013832 ↗
48. Microporosity formation and dendrite growth during solidification of aluminum alloys: modeling and experiment10.1016/j.ijheatmasstransfer.2019.118838 ↗
49. Gas dissolution process of spherical rising gas bubbles10.1016/S0009-2509(98)00094-3 ↗