Effect of combined thermomechanical treatment on structure, mechanical properties, electrochemical behavior and functional corrosion fatigue of biodegradable Fe-30Mn-5Si alloy
Source abstract
Abstract
In present study, the combined thermomechanical treatment (TMT), including the radial-shear rolling (RSR) at 900 °C followed by longitudinal rolling (RSR+LR) at 700 °C, was applied to biodegradable Fe-30Mn-5Si (wt%) alloy. The effect of these TMTs on the microstructure, phase composition, mechanical properties (ultimate tensile strength UTS, apparent yield stress σ 0.2, relative elongation to failure δ, Young`s modulus E), electrochemical behavior and functional corrosion-fatigue behavior in Hanks’ solution were studied. It was found that RSR leads to the formation of a statically recrystallized γ-austenite structure with an average grain size of 10±3 and 20±3 µm in the peripheral and central zones, respectively. The RSR+LR results in a mixture of dynamically recrystallized and dynamically polygonized structures with the average grain size of 5±1 µm. Moreover, RSR and RSR+LR lead to the formation of a single-phase FCC γ-austenite state compared to reference heat treatment (RHT), where microstructure is characterized by a two-phase state of FCC γ-austenite and HCP ε-martensite with an average grain size of 200–300 µm. Based on static mechanical tensile tests to failure, it was established that RSR and RSR+LR lead to a significant increase of UTS up to 770±21 and 935±55 MPa, σ 0.2 up to 300±38 and 490±43 MPa, and δ up to 28±2 and 19±10 %, while maintaining acceptable of E value about 165±29 and 150±8 GPa, respectively as compared to 460±41 MPa, 210±91 MPa, 11±3 %, and 140±14 GPa after RHT. The electrochemical studies showed that single-phase structure (FCC γ-austenite) formed after RSR and RSR+LR leads to the non-critical biodegradation rate lowering as compared to the two-phase state ( γ-austenite and ε-martensite) after RHT. Besides RSR and RSR+LR lead to significant improvement of functional corrosion-fatigue life in Hanks’ solution.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Corrosion Behavior and Inhibition · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. Degradable biomaterials based on magnesium corrosion10.1016/j.cossms.2009.04.001 ↗
2. Review of magnesium-based biomaterials and their applications10.1016/j.jma.2018.02.003 ↗
3. Alloying design of biodegradable zinc as promising bone implants for load-bearing applications
4. Novel Zn-based alloys for biodegradable stent applications: design, development and in vitro degradation10.1016/j.jmbbm.2016.03.018 ↗
5. Effect of silver additions on the microstructure, mechanical properties and corrosion behavior of biodegradable Fe-30Mn-6Si
6. Iron and iron-based alloys for temporary cardiovascular applications10.1007/s10856-015-5473-8 ↗
7. Biodegradable metals10.1016/j.mser.2014.01.001 ↗
8. Novel biodegradable Fe-Mn-C-S alloy with superior mechanical and corrosion properties10.1016/j.matlet.2016.10.037 ↗
9. Progress in manufacturing and processing of degradable Fe-based implants: a review10.1007/s40204-022-00189-4 ↗
10. Effect of grain size on the mechanical properties of Fe-30Mn-6Si biodegradable alloy10.1016/j.matchar.2022.112272 ↗
11. Biodegradable Fe-based alloys for use in osteosynthesis: outcome of an in vivo study after 52 weeks10.1016/j.actbio.2014.04.007 ↗
12. Improved biodegradability of Fe–Mn alloy after modification of surface chemistry and topography by a laser ablation10.1016/j.apsusc.2018.05.066 ↗
13. In vivo evaluation of biodegradability and biocompatibility of Fe30Mn alloy10.3415/VCOT-17-06-0080 ↗
14. Microstructural, mechanical, corrosion and cytotoxicity characterization of the hot forged FeMn30(wt%) alloy10.1016/j.msec.2015.09.049 ↗
15. Otsuka · 1998
16. H.C. Lin, K.M. Lin, An investigation of martensitic transformation in an Fe-30Mn-6Si shape memory alloy, 1996.10.1016/S0956-716X(95)00549-B ↗
17. Martensitic transformations and mechanical and corrosion properties of Fe-Mn-Si alloys for biodegradable medical implants10.1007/s11661-017-4458-2 ↗
18. Tunable corrosion behavior of calcium phosphate coated Fe-Mn-Si alloys for bone implant applications10.1007/s11661-018-4907-6 ↗
19. In vitro investigation of Fe30Mn6Si shape memory alloy as potential biodegradable metallic material10.1016/j.matlet.2010.10.068 ↗
20. Novel Fe-Mn-Si-Pd alloys: insights into mechanical, magnetic, corrosion resistance and biocompatibility performances10.1039/C6TB01951J ↗
21. Effect of THermomechanical Treatment on Functional Properties of Biodegradable Fe-30Mn-5Si shape memory alloy10.1007/s11661-021-06217-5 ↗
22. Effect of thermomechanical treatment on structure and functional fatigue characteristics of biodegradable fe-30mn-5si (wt%) shape memory alloy10.3390/ma14123327 ↗
23. Hot radial shear rolling and rotary forging of metastable beta Ti-18Zr-14Nb (at%) alloy for bone implants: microstructure, texture and functional properties10.1016/j.jallcom.2019.06.041 ↗
24. Influence of the radial-shear rolling (RSR) process on the microstructure, electrical conductivity and mechanical properties of a Cu–Ni–Cr–Si alloy10.1016/j.msea.2021.141676 ↗
25. S.P. Galkin, Theory and Technology of Stationary Helical Rolling of Billets and Bars of Low-Plasticity Steels and Alloys, 1998.
26. The effect of combined rolling on the structure and properties of vt1-0 titanium rods
27. A.A. Bogatov, D.A., Pavlov, D..Sh. Nukhov, Screw rolling of continuously cast blanks from structural steel grades, 2017.
28. Potapov · 1990
29. S.P. Galkin, B.A. Romantsev, E.A. Kharitonov, CIS Iron and Steel Review, (2014) 35–39.
30. Obtaining of Long-length Rods with Ultrafine-grained Structure by the Radial-shear Rolling
31. Radial-shear rolling of titanium alloy VT-8 Bars with controlled structure for small diameter ingots (≤200 mm)10.1007/s11015-018-0581-6 ↗
32. Nanotechnologies for the formation of medical implants based on titanium alloys with bioactive coatings10.1134/S1995078009110020 ↗
33. Warm cross rolling in conical shaped rolls as a method of severe plastic deformation
34. Structure and functional properties of metastable beta Ti-18Zr-14Nb (at%) alloy for biomedical applications subjected to radial shear rolling and thermomechanical treatment10.1016/j.jallcom.2017.12.119 ↗
35. Grain refinement, texture, and mechanical properties of a magnesium alloy after radial-shear rolling10.1016/j.jallcom.2018.09.065 ↗
36. Properties of the AZ31 magnesium alloy round bars obtained in different rolling processes10.1515/amm-2015-0479 ↗
37. T. Gryc, T. Bajor, H. Dyja, The Analysis of Influence the Parameters of Rolling Process in Three High Skew Rolling Mill of Az31 Magnesium Alloy Bars on Temperature Distribution, 2016.
38. Formation of the structure and properties of an Mg–Al–Zn–Mn alloy during plastic deformation by rolling10.1134/S0036029515030040 ↗
39. Theoretical and experimental analysis of aluminium bars rolling process in three-high skew rolling mill10.1515/amm-2015-0211 ↗
40. Effect of radial–shear rolling on the formation of structure and mechanical properties of Al–Ni and Al–Ca aluminum–matrix composite alloys of eutectic type10.1134/S0031918X18010039 ↗
41. Radial-shear rolling of high-strength aluminum alloys: finite element simulation and analysis of microstructure and mechanical properties10.1016/j.msea.2020.139424 ↗
42. Effect of cross rolling on the microstructure of the 40X steel
43. Effect of plastic deformation in various temperature-rate conditions on structure and mechanical properties of biodegradable Fe–30Mn–5Si alloy10.1007/s11661-023-07293-5 ↗
44. Dependence of electrochemical characteristics of a biodegradable Fe-30Mn-5Si wt% alloy on compressive deformation in a wide temperature range10.3390/met13111830 ↗
45. Relation of oxygen and temperature in the preservation of tissues by refrigeration10.3181/00379727-71-17131 ↗
46. S.M. Dubinskij, Y.S. Zhukova, A.A. Korobkova, M.S. Rulev, P.O. Kadirov, A.V. Korotitskij, Y.A. Pustov, S.D. Prokoshkin, Device for Studying Corrosion-Fatigue Destruction of Metals and Alloys During Mechanical Tests in Liquid Electrolyte, 2725108 C1, 2020.
47. Trajectory of deformed metal as basis for controlling the radial-shear and screw rolling
48. A promising technology for producing bars from a superelastic Ti-Zr-Nb alloy for medical purposes based on a combination of radial-shear rolling and rotational forging
49. Brailovski · 2003
50. Suppression of martensitic transformation in Fe50Mn23Ga27 by local symmetry breaking10.1063/1.4921928 ↗
51. Influence of thermal cycling in a Fe-Mn-Si-Cr shape memory alloy
52. Effect of therma cycling on the martensitic transformation in an Fe-24Mn-6Si shape memory alloy10.2320/matertrans1989.33.263 ↗
53. R. Perez-Saez, M. No, J. San Juan, Internal friction in Fe-Mn-Cr-Si-Ni shape memory alloys, 1994.10.1016/0925-8388(94)90485-5 ↗
54. B.C. Zolotarevskii, Mechanical Properties of Metals, n.d. [in Russian].
55. Uhlig`s corrosion handbook
56. Structure and corrosion-electrochemical behavior of bioresorbable alloys based on the Fe–Mn system10.1134/S2070205118030139 ↗
57. Corrosion behavior of fluorinated carbonyl iron-hydrophobic composites in neutral salt spray environment10.1016/j.corsci.2022.110823 ↗
58. Galvanic corrosion induced by heterogeneous bimodal grain structures in Fe-Mn implant10.1016/j.matchar.2021.111445 ↗
59. E.M. Gutman, Mechanochemistry of Solid Surfaces, World Scientific Publishing Co, Hackensack, NJ, USA, 1994.10.1142/2373 ↗
60. Mechanical and corrosion properties of hot-extruded Mg–Zn–Ga
61. Microstructure, mechanical, and corrosion properties of Mg-Zn-Ga alloy after hot rolling10.1007/s11665-024-09361-2 ↗
62. Drobyshev, High strength and ductility in a new Mg–Zn–Ga biocompatible alloy by drawing and rotary forging
63. Effect of ECAP on microstructure, mechanical properties, corrosion behavior, and biocompatibility of Mg-Ca alloy composite10.3390/jcs7070292 ↗
64. Effect of equal channel angular pressing on structure, texture, mechanical and in-service properties of a biodegradable magnesium alloy10.1016/j.matlet.2018.12.024 ↗
65. The effect of equal-channel angular pressing on microstructure, mechanical properties, and biodegradation behavior of magnesium alloyed with silver and gadolinium10.3390/cryst10100918 ↗
66. Effects of thermomechanical processing on microstructures, mechanical properties, and biodegradation behaviour of dilute Zn-Mg alloys10.1016/j.jmrt.2023.01.203 ↗
67. Bioactivity features of a Zn-1%Mg-0.1%Dy alloy strengthened by equal-channel angular pressing10.3390/biomimetics8050408 ↗