journal article·2024-12

Tensile properties and damage mechanisms of 3D printed Ti-24Nb-4Zr-8Sn alloy and polyurea interpenetrating phase composites

C.Q. Lu, S.J. Li, Z.Q. Liu, D.R. Liu, T. Zhao, D.L. Gong, W.T. Hou, R. Yang, Y.L. Hao

Publisher page

Abstract

By preparing interpenetrating phase composites (IPCs) using two-phase composites of metals and polymers, it is possible to preserve the inherent properties of the metal lattice while leveraging the exceptional characteristics of polymers. In this study, a Ti2448/polyurea composite with continuous interpenetrating phase was fabricated by infusing polyurea into a cross-laminated lattice prepared using electron beam melting (EBM) technology. The IPCs exhibit a tensile strength of 91 MPa, representing a 14 % increase over the theoretical strength. Moreover, the maximum hysteresis loss energy measures 349 J/m³, representing about ∼102 % increase over the maximum hysteresis loss energy of the lattice. The damage and failure modes of IPCs under tensile loading was revealed by finite element analysis. Our results would provide important data and valuable insights to advance the development of IPCs.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Additive Manufacturing and 3D Printing Technologies · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. Interpenetrating phase composites10.1111/j.1151-2916.1992.tb04138.x ↗
2. Deformation behavior of interpenetrating-phase composites10.1016/0266-3538(94)90037-X ↗
3. The mechanical behaviour of interpenetrating phase composites–I: modelling10.1016/S0020-7403(99)00025-9 ↗
4. Effective elastic and plastic properties of interpenetrating multiphase composites10.1023/B:ACMA.0000003972.32599.0c ↗
5. Particulate reinforced metal matrix composites—a review10.1007/BF00544448 ↗
6. Mechanical properties of Al2O3 and Al2O3/Al interpenetrated functional gradient structures by 3D printing and melt infiltration10.1016/j.jallcom.2023.169948 ↗
7. High damping capacity of AlSi10Mg-NiTi lattice structure interpenetrating phase composites prepared by additive manufacturing and pressureless infiltration10.1016/j.jallcom.2022.164075 ↗
8. Towards high-performance bioinspired composites10.1002/adma.201201471 ↗
9. Influence of cell shape on mechanical properties of Ti–6Al–4V meshes fabricated by electron beam melting method10.1016/j.actbio.2014.06.010 ↗
10. Compressive and fatigue behavior of functionally graded Ti-6Al-4V meshes fabricated by electron beam melting10.1016/j.actamat.2018.02.060 ↗
11. Bio-mimetic mechanisms of natural hierarchical materials: a review10.1016/j.jmbbm.2012.10.012 ↗
12. Evidence for a material gradient in the adhesive tarsal setae of the ladybird beetle Coccinella septempunctata10.1038/ncomms2576 ↗
13. The mechanics of cutting and the form of shark teeth (Chondrichthyes, Elasmobranchii)10.1007/BF00539785 ↗
14. Multiscale geometric design principles applied to 3D printed schwarzites10.1002/adma.201704820 ↗
15. Morphogenesis and mechanostabilization of complex natural and 3D printed shapes10.1126/sciadv.1400052 ↗
16. Unleashing enhanced compressive strength: 3D printed octopus-inspired suction cups using topological engineering10.1021/acsapm.3c01721 ↗
17. Topologically engineered 3D printed architectures with superior mechanical strength10.1016/j.mattod.2021.03.014 ↗
18. Manufacturing and low-velocity impact response of a new composite material: Metal porous polymer composite (MPPC)
19. Mechanical behavior of aluminum foam/polyurethane interpenetrating phase composites under monotonic and cyclic compression10.1016/j.compositesa.2018.10.026 ↗
20. Crush performance of multifunctional hybrid foams based on an aluminium alloy open-cell foam skeleton10.1016/j.polymertesting.2018.03.009 ↗
21. Interpenetrating phase composite foam based on porous aluminum skeleton for high energy absorption10.1016/j.polymertesting.2020.106917 ↗
22. Experimental measurements and numerical modeling of dynamic compression response of an interpenetrating phase composite foam10.1016/j.mechrescom.2012.03.002 ↗
23. Cyclic compression behavior and energy dissipation of aluminum foam–polyurethane interpenetrating phase composites10.1016/j.compositesa.2015.07.016 ↗
24. Radially graded porous structure design for laser powder bed fusion additive manufacturing of Ti-6Al-4V alloy10.1016/j.jmatprotec.2021.117186 ↗
25. Microstructure and fracture properties of open-cell porous Ti-6Al-4V with high porosity fabricated by electron beam melting10.1016/j.matchar.2018.02.016 ↗
26. Mechanical properties of 3D printed interpenetrating phase composites with novel architectured 3D solid-sheet reinforcements10.1016/j.compositesa.2016.02.009 ↗
27. Enhanced fracture toughness in architected interpenetrating phase composites by 3D printing10.1016/j.compscitech.2018.08.009 ↗
28. Ceramic microlattice and epoxy interpenetrating phase composites with simultaneous high specific strength and specific energy absorption10.1016/j.matdes.2022.111206 ↗
29. Ti-PEEK interpenetrating phase composites with minimal surface for property enhancement of orthopedic implants10.1016/j.compstruct.2023.117689 ↗
30. Enhanced mechanical and thermal properties in 3D printed Al2O3 lattice/ epoxy interpenetrating phase composites10.1016/j.mechmat.2024.104930 ↗
31. Engineering the Interface of Cu-hBN immiscible system using 3D printing to enhance mechanical and thermal properties10.1021/acsaenm.3c00722 ↗
32. Compressive properties of 3-D printed Mg–NiTi interpenetrating-phase composite: Effects of strain rate and temperature10.1016/j.compositesb.2021.108783 ↗
33. Interpenetrating phase composites with 3D printed triply periodic minimal surface (TPMS) lattice structures10.1016/j.compositesb.2022.110351 ↗
34. Compression fatigue behavior of Ti–6Al–4V mesh arrays fabricated by electron beam melting10.1016/j.actamat.2011.10.051 ↗
35. Electron beam melted beta-type Ti–24Nb–4Zr–8Sn porous structures with high strength-to-modulus ratio10.1016/j.jmst.2016.03.020 ↗
36. Compressive and fatigue behavior of beta-type titanium porous structures fabricated by electron beam melting10.1016/j.actamat.2016.12.052 ↗
37. Enhanced fatigue characteristics of a topology-optimized porous titanium structure produced by selective laser melting
38. Material characterisation and computational thermal modelling of electron beam powder bed fusion additive manufacturing of Ti2448 titanium alloy10.3390/ma14237359 ↗
39. Mechanical behavior of bio-inspired crossed-lamellar microstructures for achieving high-performance composites10.1016/j.engfracmech.2023.109397 ↗
40. Anisotropic mechanical behaviors and their structural dependences of crossed-lamellar structure in a bivalve shell10.1016/j.msec.2015.11.003 ↗
41. The relationship between mechanical properties and crossed-lamellar structure of mollusk shells10.1016/j.msea.2006.09.156 ↗
42. C. Eschey, S. Lutzmann, M. Zaeh, Examination of the powder spreading effect in electron beam melting (EBM), (2009).
43. M. Sigl, S. Lutzmann, M. Zaeh, Transient physical effects in electron beam sintering, (2006).
44. Powder bed charging during electron-beam additive manufacturing10.1016/j.actamat.2016.11.012 ↗
45. Spinodal decomposition coupled with a continuous crystal ordering in a titanium alloy10.1016/j.actamat.2022.117969 ↗
46. Assessment of the interfacial properties from fatigue hysteresis loss energy in ceramic-matrix composites with different fiber preforms at room and elevated temperatures10.1016/j.msea.2014.06.092 ↗
47. Mathematical modelling of frequency-dependent hysteresis and energy loss of FeBSiC amorphous alloy10.1016/j.jmmm.2016.08.061 ↗
48. Energy loss and hysteresis of reversible magnetization processes in iron-based soft magnetic composites10.1016/j.jmmm.2023.171291 ↗
49. A ZA22/Al interpenetrating phase composite with high compressive stress plateau and high damping capacity10.1016/j.matlet.2023.135799 ↗
50. Static and dynamic damping mechanical performance of architected metal-epoxy interpenetrating phase composites10.1016/j.compositesa.2024.108171 ↗
51. Mechanical surface treatment of EBM Ti6Al4V components: Effects of the resulting surface layer state on fatigue mechanisms and service life10.1016/j.msea.2022.143422 ↗
52. Improved quality and functional properties of Ti-6Al-4V ELI alloy for personalized orthopedic implants fabrication with EBM process10.1016/j.jmapro.2022.02.011 ↗
53. Influence of processing parameters on the evolution of melt pool, porosity, and microstructures in Ti-6Al-4V alloy parts fabricated by selective laser melting10.1007/s40964-017-0030-2 ↗
54. de Paz, Effect of process parameters settings and thickness on surface roughness of EBM produced Ti-6Al-4V10.1108/13552541211250391 ↗
55. Effect of energy density of incident beam on mechanical property of titanium alloy products fabricated by electron beam melting (EBM) method10.4028/www.scientific.net/MSF.706-709.488 ↗
56. Enhancing structural resilience by using 3D printed complex polymer reinforcement for high damage tolerant structures10.1016/j.conbuildmat.2024.136085 ↗
57. Low frequency damping capacities and mechanical properties of Mg-Si alloys
58. Microstructure, mechanical and damping properties of Mg–Er–Gd–Zn alloy reinforced with stacking faults10.1016/j.matdes.2015.04.037 ↗