Comprehensive characterization of spark plasma sintered ZrB2-SiCp-SiCw composite and its corresponding orthogonal cutting simulation
Source abstract
Abstract
A composite consisting of 12.5 wt% SiC particles and 12.5 wt% SiC whiskers in a ZrB 2 matrix (ZrB 2-SiC p-SiC w) was produced using spark plasma sintering. The sintering process was carried out at a temperature of 1900 °C and a pressure of 40 MPa for a duration of 7 minutes. X-ray photoelectron spectroscopy analysis confirmed the presence of C-C, C-Si, O-B, O-Zr, O-Si, and Zr-B bonds. Scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy analyses revealed the presence of silicon and carbon in the ZrB 2 phase. The nano-indentation hardnesses and elastic moduli of ZrB 2 and SiC were measured as 2104.58 and 2268.97 Vickers and 397.58 and 394.27 GPa, respectively, under a load of 100 mN and a loading rate of 0.4 mN/sec. The orthogonal cutting process of an Al6061 workpiece with a ZrB 2-SiC p-SiC w cutting tool was simulated using DEFORM 2D software. The response surface method was used to develop a model to evaluate the relationship between cutting parameters (tool tip radius, cutting speed, and rake angle), cutting force, feeding force, and maximum temperature. It was found that cutting and feeding forces decrease with increasing cutting speed and rake angle, while increasing the tool tip radius increases these forces. The tool and workpiece endure a higher maximum temperature as the cutting speed and tool tip radius rise, but the maximum temperature drops as the rake angle increases.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Effect of nano and micro SiC particles on the microstructure and fracture toughness of ZrB2-SiC nanocomposite produced by SPS method10.1088/2053-1591/ab2e45 ↗
2. Pop-in characteristic induced by nanoindentation in ZrB2-SiC composites
3. Introduction to H2020 project C 3 HARME – next generation ceramic composites for combustion harsh environment and space10.1080/17436753.2018.1509822 ↗
4. Oxidation kinetics of ZrB2-and HfB2-powders and their SiC reinforced composites10.1016/j.corsci.2020.109024 ↗
5. A TEM study on the microstructure of spark plasma sintered ZrB2-based composite with nano-sized SiC dopant10.1016/j.pnsc.2020.11.010 ↗
6. F.M.A. Bellosi, Fabrication and properties of zirconium diboride-based ceramics for UHT applications, hot structures and thermal protection systems for space vehicles, in: Proceedings of the Fourth European Workshop Held 26-29 November, 2002 in Palermo, Italy. (2003) 65.
7. Preparation and characterization of ZrB2-SiC ultra-high temperature ceramics by microwave sintering10.1007/s11706-010-0091-3 ↗
8. Influence of SiAlON addition on the microstructure development of hot-pressed ZrB2–SiC composites10.1016/j.ceramint.2020.04.258 ↗
9. Role of TiCN addition on the characteristics of reactive spark plasma sintered ZrB2-based novel composites
10. Processing and mechanical properties of short carbon fibers toughened zirconium diboride-based ceramics10.1016/j.matdes.2008.03.011 ↗
11. Effect of carbon source on the synthesis of ZrB2–SiC composite powders10.1088/1757-899X/770/1/012095 ↗
12. Effect of graphite flake on the mechanical properties of hot pressed ZrB2–SiC ceramics10.1016/j.matlet.2008.07.027 ↗
13. Reactive hot pressing route for dense ZrB2-SiC and ZrB2-SiC-CNT ultra-high temperature ceramics10.1016/j.jeurceramsoc.2020.07.039 ↗
14. Enhanced fracture toughness of ZrB2–SiCw ceramics with graphene nano-platelets10.1016/j.ceramint.2020.06.275 ↗
15. Effect of SiC whiskers and graphene nanosheets on the mechanical properties of ZrB2-SiCw-Graphene ceramic composites10.1016/j.ceramint.2016.06.014 ↗
16. ZrB2-SiC Based Ultra High Temperature Ceramic Composites: Mechanical Performance and Measurement and Design of Thermal Residual Stresses for Hypersonic Vehicle Applications
17. Effects of HfB2 addition on pressureless sintering behavior and microstructure of ZrB2-SiC composites10.1016/j.ijrmhm.2020.105371 ↗
18. Study on ZrB2-based ceramics reinforced with SiC fibers or whiskers machined by micro-electrical discharge machining10.3390/mi11110959 ↗
19. Oxidation of ZrB2 ceramics containing SiC as particles, whiskers, or short fibers10.1111/j.1551-2916.2011.04726.x ↗
20. Reinforcing effects of SiC whiskers and carbon nanoparticles in spark plasma sintered ZrB2 matrix composites10.1016/j.ceramint.2018.07.258 ↗
21. Effect of silicon carbide and graphite additives on the pressureless sintering mechanism and microstructural characteristics of ultra-high temperature ZrB2 ceramics composites
22. Thermal shock behavior of SiC-whisker-reinforced diboride ultrahigh-temperature ceramics10.1016/j.scriptamat.2008.02.023 ↗
23. High temperature strength of hot pressed ZrB2–20 vol% SiC ceramics based on ZrB2 starting powders prepared by different carbo/boro-thermal reduction routes10.1016/j.jeurceramsoc.2013.03.001 ↗
24. Spark plasma sintering of Al-doped ZrB2–SiC composite10.1016/j.ceramint.2018.11.098 ↗
25. Fabrication and characterization of SiC whisker reinforced reaction bonded SiC composite10.1016/j.ceramint.2012.06.047 ↗
26. Effect of in-situ grown SiC nanowires on the mechanical properties of HfC-ZrB2-SiC modified C/C composites10.1016/j.jallcom.2017.08.060 ↗
27. Improved fracture toughness of laminated ZrB2-SiC-MoSi2 ceramics using SiC whisker10.1016/j.ceramint.2018.02.078 ↗
28. Development of advanced composite ceramic tool material10.1016/S0025-5408(96)00078-5 ↗
29. Toughened ZrB2-based ceramics through SiC whisker or SiC chopped fiber additions10.1016/j.jeurceramsoc.2009.11.012 ↗
30. A numerical approach to the heat transfer in monolithic and SiC reinforced HfB2, ZrB2 and TiB2 ceramic cutting tools10.1016/j.ceramint.2019.05.095 ↗
31. Study on in-situ synthesis of ZrB2 whiskers in ZrB2–ZrC matrix powder for ceramic cutting tools10.1016/j.ijrmhm.2012.11.001 ↗
32. 3D characterization of the SiC nanoparticle distribution in ZrB2–SiC ceramics with synchrotron X-ray nanoscale computed tomography10.1016/j.ceramint.2021.01.138 ↗
33. Response surface methodology10.1002/wics.73 ↗
34. Reminga Response Surface Methodology,CASOS Technical Report
35. Dean · Response Surface Methodology, Design and Analysis of Experiments · 2017 · 56510.1007/978-3-319-52250-0_16 ↗
36. Kleijnen · 2015 · 81
37. Barton · 2013 · 1307
38. Box-Behnken design: an alternative for the optimization of analytical methods10.1016/j.aca.2007.07.011 ↗
39. Predictive modelling of microstructure changes, micro-hardness and residual stress in machining of 304 austenitic stainless steel10.1016/j.ijmachtools.2018.03.008 ↗
40. Experimental analysis and optimisation of tool wear in dry machining of aluminium alloys10.1016/S0043-1648(03)00105-4 ↗
41. Cutting temperature effect on PCBN and CVD coated carbide tools in hard turning of D2 tool steel10.1016/j.ijrmhm.2014.11.001 ↗
42. Wear and tribological performance of different ceramic tools in dry high speed machining of Ni-Co-Cr precipitation hardenable aerospace superalloy10.1080/10402004.2018.1486494 ↗
43. Microstructure and properties of silicon carbide whisker reinforced zirconium diboride ultra-high temperature ceramics10.1016/j.solidstatesciences.2008.05.010 ↗
44. SFTC, DEFORM™ v10.2, Scientific Forming Technologies Corporation (SFTC) Material data base, (2013).
45. Predicting the effects of grain size on machining-induced residual stresses in steels
46. Effects of sequential cuts on residual stresses when orthogonal cutting steel AISI 104510.1016/j.procir.2015.03.032 ↗
47. Filice · 2007 · 263
48. A machining-based methodology to identify material constitutive law for finite element simulation10.1007/s00170-014-6583-z ↗
49. Prospects of direct growth boron nitride films as substrates for graphene electronics10.1557/jmr.2013.323 ↗
50. High-temperature chemistry and oxidation of ZrB 2 ceramics containing SiC, Si3N4, Ta5Si3, and TaSi210.1111/j.1551-2916.2008.02420.x ↗
51. Nano-diamond reinforced ZrB2–SiC composites10.1016/j.ceramint.2020.01.008 ↗
52. Sintering of 6H(α)-SiC and 3C(β)-SiC commercial powders with B4C and C additives10.1023/A:1014964701803 ↗
53. Influence of the α/β-SiC phase transformation on microstructural development and mechanical properties of liquid phase sintered silicon carbide10.1023/A:1004552704872 ↗
54. The conversion of cubic and hexagonal silicon carbide as a function of temperature and pressure
55. Optimization of effective parameters on thermal shock resistance of ZrB2-SiC-based composites prepared by SPS: Using Taguchi design10.1016/j.matchemphys.2017.04.062 ↗
56. New role of screw dislocation in twin lamella during deformation: an in situ TEM study at the atomic scale10.1016/j.msea.2018.05.053 ↗
57. Observations on nanoscale te precipitates in CdZnTe crystals grown by the traveling heater method using high resolution transmission electron microscopy10.3390/cryst8010026 ↗
58. Combined role of SiC particles and SiC whiskers on the characteristics of spark plasma sintered ZrB2 ceramics10.1016/j.ceramint.2019.11.027 ↗