Enhancing the mechanical property and thermal stability through the combination effect of La and Y in ODS-Cu alloys prepared by powder metallurgy
Source abstract
Abstract
In this work, Cu-1.5 wt%Y (Cu-Y) and Cu-0.75 wt%Y-0.75 wt%La (Cu-Y-La) were prepared by mechanical alloying combined with spark plasm sintering and hot rolling, followed with annealing at different temperatures. The effects of the introduction of La and annealing temperatures on the microstructures, mechanical properties, electrical conductivity and thermal stability of Cu-Y alloys were investigated. Both Cu-Y and Cu-Y-La obtain the heterogeneous mixed grain structures composed of coarse grains and fine grains, and oxide nanoparticles are uniformly dispersed in Cu matrix. With the introduction of La, the grains and oxide nanoparticles are refined, and LaYO 3 nanoparticles with the coherent interfacial structure can be observed in Cu-Y-La. After annealing at 500 ℃, both Cu-Y and Cu-Y-La obtain the most excellent comprehensive tensile properties and highest electrical conductivity (63 %IACS for Cu-Y and 62 %IACS for Cu-Y-La). Benefited from effectively enhanced grain boundary strengthening and particle strengthening mechanisms induced by the combination effect of La and Y, Cu-Y-La shows higher strength than that of Cu-Y (after annealing at 500 ℃, 244 MPa of yield strength for Cu-Y and 300 MPa for Cu-Y-La). Meanwhile, benefited from improved dynamics stability of the Cu matrix induced by significantly refined precipitates and the formation of LaYO 3 nanoparticles with the coherent interfacial structure after introducing La, the better softening resistance is achieved by Cu-Y-La in comparsion with Cu-Y, and almost 100 ℃ improvement of the softening temperature is achieved (966 ℃ for Cu-Y-La and 870 ℃ for Cu-Y).
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · High-Temperature Coating Behaviors · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. New insights on the formation of supersaturated solid solutions in the Cu-Cr system deformed by high-pressure torsion10.1016/j.actamat.2014.02.003 ↗
2. Microstructure and properties of nanocrystalline copper–niobium alloy with high strength and high conductivity10.1016/j.msea.2013.08.035 ↗
3. Research of mechanical and electrical properties of Cu-Sc and Cu-Zr alloys10.1007/s43452-020-00035-z ↗
4. Anomalous recovery of work hardening rate in Cu-Mn alloys with high stacking fault energies under uniaxial compression10.1016/j.msea.2018.11.103 ↗
5. The precipitation behaviour of ITER-grade Cu-Cr-Zr alloy after simulating the thermal cycle of hot isostatic pressing10.1016/S0022-3115(99)00285-8 ↗
6. Property and thermal stability of in situ composite Cu-Cr alloy contact cable10.1016/j.jmatprotec.2004.08.013 ↗
7. Thermal stability and high-temperature mechanical performance of nanostructured W-Cu-Cr-ZrC composite10.1016/j.compositesb.2020.108600 ↗
8. Strength and fatigue of dispersion-strengthened copper10.1016/0022-3115(91)90076-J ↗
9. Fabrication and characterization of dispersion strengthened Cu-0.8%Y10.1016/j.fusengdes.2020.111548 ↗
10. Role of tantalum concentration, processing temperature, and strain-rate on the mechanical behavior of copper-tantalum alloys10.1016/j.actamat.2021.116706 ↗
11. Enhanced mechanical and electrical properties of in situ synthesized nano-tungsten dispersion-strengthened copper alloy10.1016/j.msea.2020.140161 ↗
12. Creep in copper dispersion strengthened with alumina particles (ODS copper)10.1016/S0921-5093(02)00631-7 ↗
13. A novel approach for strengthening Cu-Y2O3 composites by in situ reaction at liquidus temperature10.1016/j.msea.2013.07.007 ↗
14. Fabrication and characterization of Y2O3 dispersion strengthened copper alloys10.1016/j.jnucmat.2014.08.050 ↗
15. In-situ fabrication of yttria dispersed copper alloys through MA-HIP process10.1016/j.nme.2018.06.024 ↗
16. Principles of particle selection for dispersion-strengthened copper10.1016/0921-5093(93)90398-X ↗
17. Fabrication and characterization of Cu reinforced with Y-enriched particles following a novel powder metallurgy route
18. Microstructure and mechanical properties of mechanically alloyed ODS copper alloy for fusion material application10.1016/j.nme.2018.05.019 ↗
19. Microstructural and mechanical characterization of Cu-0.8 wt%Y10.1016/j.fusengdes.2015.06.113 ↗
20. Doping Ti to achieve microstructural refinement and strength enhancement in a high volume fraction Y2O3 dispersion strengthened Cu10.1016/j.jallcom.2018.04.224 ↗
21. Effects of zirconium addition on the material properties and microstructure of ODS-Cu alloys10.1016/j.jallcom.2021.163328 ↗
22. Influence of lanthanum on enhancement of mechanical and electrical properties of Cu-Al2O3 composites10.1016/j.jre.2018.08.016 ↗
23. Microstructural changes of oxide dispersion strengthened copper powders fabricated by mechanical alloying10.1016/j.fusengdes.2021.112804 ↗
24. Multiscale structural characterization of yttria dispersed copper alloys fabricated by hot isostatic processing of mechanically alloyed powders10.1016/j.mtla.2020.100892 ↗
25. Effects of size and oxidation treatment for SiC particles on the microstructures and mechanical properties of SiCp/Al composites prepared by powder metallurgy10.1016/j.msea.2022.143664 ↗
26. Microstructure and room temperature hardening of ultra-fine-grained oxide-dispersion strengthened copper prepared by cryomilling10.1016/j.msea.2004.05.049 ↗
27. Kelly · 1971
28. The strain and grain size dependence of the flow stress of copper10.1016/0001-6160(82)90221-8 ↗
29. Dispersion strengthened copper: properties and applications, high conduct
30. Nanocrystalline-grained tungsten prepared by surface mechanical attrition treatment: microstructure and mechanical properties10.1016/j.jnucmat.2016.08.032 ↗