journal article·2025-05Open access

A new non-equiatomic Ti40Zr25Nb25Ta5Al5 refractory high entropy alloy for potential biomedical applications

L. Mustafi, V.T. Nguyen, T. Song, X.-B. Chen, D.M. Fabijanic, M. Qian

Abstract

A non-equiatomic Ti40Zr25Nb25Ta5Al5 refractory high entropy alloy (RHEA) was designed for potential biomedical applications by replacing 5 at.% Ta with 5 at.% Al in a precursor Ti40Zr25Nb25Ta10 alloy. This simple and low-cost strategy reduced the alloy density from 7.2 to 6.5 g/cm 3 (estimated using the 'rule of mixtures') and increased the yield strength (σ ys ) from 875 to 960 MPa, while still allowing the RHEA to achieve a high tensile ductility of about 17 % in the as-cast condition. Few bio-applicable metallic alloys can achieve such tensile strength-ductility combinations in the as-cast condition. Compared to the mill-annealed medical-grade Ti-6Al-4V (wt.%) alloy, this as-cast RHEA offers significantly higher yield strength and ductility, along with a much lower cytotoxic aluminium content (1.8 wt.%). Furthermore, the as-cast RHEA has a much higher admissible strain (1.12 %) than Ti-6Al-4V (0.75 %) and also exhibits better corrosion resistance in Hank’s solution than Ti-6Al-4V. These evaluation results demonstrate the potential of this Ti40Zr25Nb25Ta5Al5 RHEA for biomedical applications. To elucidate the origin of these attractive properties, the solidification microstructure, tensile deformation mechanisms and surface oxide film of this RHEA were systematically investigated. A series of novel experimental observations were obtained and are discussed in detail. • Replacing 5 at.% Ta with 5 at.% Al in the Ti40Zr25Nb25Ta10 RHEA yields a new strong and ductile RHEA with lower density. • This new Ti40Zr25Nb25Ta5 RHEA exhibited superior yield strength and tensile ductility compared to medical-grade Ti-6Al-4V. • Plastic deformation in this RHEA involved primary and secondary shear bands, along with prominent dislocation loops. • This RHEA further exhibited superior elastic admissible strain and corrosion resistance compared to Ti-6Al-4V.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High Entropy Alloys Studies · Additive Manufacturing Materials and Processes · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (83)

Show source-provided references
1. Refractory high-entropy alloys10.1016/j.intermet.2010.05.014 ↗
2. Size-dependent plasticity in an Nb25Mo25Ta25W25 refractory high-entropy alloy10.1016/j.actamat.2013.11.049 ↗
3. Ultrastrong ductile and stable high-entropy alloys at small scales10.1038/ncomms8748 ↗
4. New ternary equi-atomic refractory medium-entropy alloys with tensile ductility: Hafnium versus titanium into NbTa-based solution10.1016/j.intermet.2019.01.004 ↗
5. Enhanced strength and ductility in a high-entropy alloy via ordered oxygen complexes10.1038/s41586-018-0685-y ↗
6. A critical review of high entropy alloys and related concepts10.1016/j.actamat.2016.08.081 ↗
7. Low-density, refractory multi-principal element alloys of the Cr–Nb–Ti–V–Zr system: microstructure and phase analysis10.1016/j.actamat.2012.11.032 ↗
8. Corrosion-resistant high-entropy alloys: a review10.3390/met7020043 ↗
9. Corrosion and serration behaviors of TiZr0. 5NbCr0. 5V x Mo y high entropy alloys in aqueous environments10.3390/met4040597 ↗
10. A strong and ductile biocompatible Ti40Zr25Nb25Ta5Mo5 high entropy alloy10.1016/j.jmrt.2024.05.118 ↗
11. Effect of oxygen on the microstructure, tensile properties and deformation behaviours of a biocompatible Ti40Zr25Nb25Ta10 high entropy alloy10.1016/j.jmst.2024.06.022 ↗
12. Investigation of hafnium for biomedical applications: corrosion and tribocorrosion in simulated body fluids
13. Impacts of trace carbon on the microstructure of as-sintered biomedical Ti–15Mo alloy and reassessment of the maximum carbon limit10.1016/j.actbio.2013.10.034 ↗
14. A review on biomedical implant materials and the effect of friction stir based techniques on their mechanical and tribological properties10.1016/j.jmrt.2022.01.050 ↗
15. Effect of alloying elements on mechanical properties of titanium alloys for medical implants10.2320/matertrans1989.34.1217 ↗
16. Cytocompatibility of various metal and development of new titanium alloys for medical implants10.1016/S0921-5093(97)00809-5 ↗
17. Microstructure and properties of aluminum-containing refractory high-entropy alloys10.1007/s11837-014-1066-0 ↗
18. Effect of aluminum on the microstructure and properties of two refractory high-entropy alloys10.1016/j.actamat.2014.01.029 ↗
19. Effect of Al addition on mechanical properties and microstructure of refractory AlxHfNbTaTiZr alloys10.1016/j.jallcom.2014.11.064 ↗
20. Characterization and modeling of NbNiTaTiW and NbNiTaTiW-Al refractory high-entropy alloys10.1007/s11661-019-05384-w ↗
21. Compositional variation effects on the microstructure and properties of a refractory high-entropy superalloy AlMo0. 5NbTa0. 5TiZr10.1016/j.matdes.2017.11.033 ↗
22. The AlMo0. 5NbTa0. 5TiZr refractory high entropy superalloy: experimental findings and comparison with calculations using the CALPHAD method
23. 1.104 - Shape Memory Alloys for Use in Medicine
24. Compositional design of strong and ductile (tensile) Ti-Zr-Nb-Ta medium entropy alloys (MEAs) using the atomic mismatch approach10.1016/j.msea.2018.11.054 ↗
25. A novel quaternary equiatomic Ti-Zr-Nb-Ta medium entropy alloy (MEA)10.1016/j.intermet.2018.07.008 ↗
26. Implications of metallic corrosion in total knee arthroplasty
27. Solid-solution phase formation rules for multi-component alloys10.1002/adem.200700240 ↗
28. Phase stability in high entropy alloys: formation of solid-solution phase or amorphous phase10.1016/S1002-0071(12)60080-X ↗
29. Phase selection rules for cast high entropy alloys: an overview10.1179/1743284715Y.0000000018 ↗
30. Structure and mechanical properties of a light-weight AlNbTiV high entropy alloy10.1016/j.matlet.2014.11.162 ↗
31. Powder metallurgy processing of a WxTaTiVCr high-entropy alloy and its derivative alloys for fusion material applications10.1038/s41598-017-02168-3 ↗
32. Comprehensive comparison of various techniques for the analysis of elemental distributions in thin films10.1017/S1431927611000523 ↗
33. Influence of bovine serum albumin in Hanks' solution on the corrosion and stress corrosion cracking of a magnesium alloy10.1016/j.msec.2017.06.002 ↗
34. Guidance on Good Cell Culture Practice (GCCP)
35. Freshney · 2015
36. Helgason · 2005
38. Microstructure, tensile properties and deformation behaviour of a promising bio-applicable new Ti35Zr15Nb25Ta25 medium entropy alloy (MEA)10.1016/j.msea.2021.141805 ↗
39. Last-stage solidification of alloys: theoretical model of dendrite-arm and grain coalescence10.1007/s11661-003-0083-3 ↗
40. Migration of solidification grain boundaries and prediction10.1038/s41467-022-33482-8 ↗
41. Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element10.2320/matertrans.46.2817 ↗
42. Deformation twinning in Ti48. 9Zr32. 0Nb12. 6Ta6. 5 medium entropy alloy10.1016/j.msea.2021.140931 ↗
43. Microstructure and room temperature mechanical properties of different 3 and 4 element medium entropy alloys from HfNbTaTiZr system10.3390/e21020114 ↗
44. Structures and properties of biocompatible Ti-Zr-Nb-Fe-Mo medium entropy alloys
45. Mechanical properties of cast Ti-6Al-4V-XCu alloys10.1111/j.1365-2842.2004.01347.x ↗
46. The use of titanium for medical applications in the USA10.1016/0921-5093(96)10243-4 ↗
47. New developments of Ti-based alloys for biomedical applications10.3390/ma7031709 ↗
48. Development of Ti–Nb–Zr alloys with high elastic admissible strain for temporary orthopedic devices10.1016/j.actbio.2015.03.023 ↗
49. Design and mechanical properties of new β type titanium alloys for implant materials10.1016/S0921-5093(97)00808-3 ↗
50. Microstructure and properties of a new beta titanium alloy, Ti-12Mo-6Zr-2Fe, developed for surgical implants
51. Standard Specification for Wrought Titanium-6Aluminum-4Vanadium ELI (Extra Low Interstitial) Alloy for Surgical Implant Applications (UNS R56401)
52. Ti-6Al-4V additively manufactured by selective laser melting with superior mechanical properties10.1007/s11837-015-1297-8 ↗
53. H.E. Boyer, ASM International, second ed., Materials Park, OH, 2002.
54. Mechanical properties of biomedical titanium alloys10.1016/S0921-5093(97)00806-X ↗
55. Comparison among mechanical properties of investment-cast cp Ti, Ti-6Al-7Nb and Ti-15Mo-1Bi alloys10.2320/matertrans.45.3028 ↗
56. Surface characteristics and castability of Zr-14Nb alloy dental castings10.4012/dmj.2014-117 ↗
57. 7 - Titanium Alloys
58. Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: a review10.1016/j.biomaterials.2016.01.012 ↗
59. Impact of scandium on mechanical properties, corrosion behavior, friction and wear performance, and cytotoxicity of a β-type Ti–24Nb–38Zr–2Mo alloy for orthopedic applications10.1016/j.actbio.2021.07.061 ↗
60. Effect of thermomechanical treatment on the mechanical and microstructural evolution of a β-type Ti-40.7Zr–24.8Nb alloy
61. Theoretical study of the effects of alloying elements on the strength and modulus of β-type bio-titanium alloys10.1016/S0921-5093(98)00886-7 ↗
62. Design of TiZrNbTa multi-principal element alloys with outstanding mechanical properties and wear resistance10.1016/j.msea.2022.143203 ↗
63. Ultralight, ductile metal mechanical metamaterials with super elastic admissible strain (0.1)10.1016/j.jmst.2023.03.043 ↗
64. Dual phase synergy enabled large elastic strains of nanoinclusions in a dislocation slip matrix composite10.1021/acs.nanolett.8b00427 ↗
65. Mechanical behavior and microstructure of Ti20Hf20Zr20Ta20Nb20 high-entropy alloy loaded under quasi-static and dynamic compression conditions10.1016/j.matchar.2015.11.018 ↗
66. Elastic deformation behavior of multi-functional Ti–Nb–Ta–Zr–O alloys10.2320/matertrans.46.3001 ↗
67. Kinking in a refractory TiZrHfNb0. 7 medium-entropy alloy10.1016/j.matlet.2020.127369 ↗
68. Local chemical fluctuation mediated ductility in body-centered-cubic high-entropy alloys10.1016/j.mattod.2021.02.022 ↗
69. Ductile Ti1. 5ZrNbAl0. 3 refractory high entropy alloy with high specific strength10.1016/j.matlet.2021.129428 ↗
70. Chemical ordering enhancing mechanical properties of Nb25Ti35V5Zr35Alx refractory high-entropy alloys10.1016/j.jallcom.2025.178990 ↗
71. Effect of oxygen on microstructure and mechanical properties of (TiZrNbTa) 100-xOx (x= 0∼ 6.0) high-entropy alloys10.1016/j.msea.2025.147800 ↗
72. The cleavage strength of polycrystals
73. Six decades of the Hall–Petch effect–a survey of grain-size strengthening studies on pure metals10.1080/09506608.2016.1191808 ↗
74. Mechanical, corrosion, and wear properties of biomedical Ti–Zr–Nb–Ta–Mo high entropy alloys10.1016/j.jallcom.2020.157997 ↗
75. Microstructural, mechanical and electrochemical characterization of TiZrTaHfNb and Ti1. 5ZrTa0. 5Hf0. 5Nb0. 5 refractory high-entropy alloys for biomedical applications10.1016/j.intermet.2019.106572 ↗
76. Electrochemical properties, chemical composition and thickness of passive film formed on novel Ti–20Nb–10Zr–5Ta alloy10.1016/j.electacta.2013.03.086 ↗
77. Long-term corrosion resistance of new Ti–Ta–Zr alloy in simulated physiological fluids by electrochemical and surface analysis methods10.1016/j.corsci.2015.01.038 ↗
78. Characteristics of oxide films on Ti-(10–75) Ta alloys and their corrosion performance in an aerated Hank’s balanced salt solution10.1016/j.apsusc.2019.145013 ↗
79. Corrosion behavior of Ti–Nb Ta–Zr–Fe alloy for biomedical applications in Ringer's solution10.1016/S1003-6326(15)63875-4 ↗
80. Validation of corrosion rates measured by the Tafel extrapolation method10.1016/j.corsci.2005.05.046 ↗
81. Testing validity of the Tafel extrapolation method for monitoring corrosion of cold rolled steel in HCl solutions–experimental and theoretical studies10.1016/j.corsci.2009.08.055 ↗
82. Investigating accuracy of the Tafel extrapolation method in HCl solutions10.1016/j.corsci.2009.03.001 ↗
83. Chemical oxidation of Ti–6Al–4V for improved wear and corrosion resistance10.1179/174329408X286097 ↗